Question about 1994 Volkswagen Golf

1 Answer

What tools do you need for changing a front wheel bearing on a mk3 golf

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

I used a hammer, adjustable spanner and a screwdriver and remeber the copper grease, make sure its lubricated properly while you've got the chance. its quite an easy job on the golf, but just take your time as i've heard people rushing it and not tightening something properly.

Posted on Apr 23, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What tools are needed to change the hub an wheel bearing on front of a 1993 vw golf


you will need a hub puller , these are readily available and are for many vehicles , not one for the exact vehicle ,you will then need to take the hub to a garage to "press" out the old bearing and press the new one in , you couldn't afford to buy the press just for diy use

Nov 23, 2014 | Cars & Trucks

1 Answer

Do you need to have a special tool to change a front wheel bearing on a Kia Sportage 4x4


Any front drive car will be more complex to change a front wheel bearing than the old read-drive cars. It may indeed need a special tool.

Oct 20, 2014 | Cars & Trucks

1 Answer

I need to change front wheel bearing on y reg golf ,


I have found a link that gives step by step instructions for this problem. Link: http://www.ehow.com/how_2248505_replace-front-wheel-bearings-car.html Hope this helps! Please give 4 thumbs up!

Apr 18, 2011 | Volkswagen GTI Cars & Trucks

1 Answer

How do I change the springs on front of my vw polo mk3


on the mk3 vw you just loosen the 7mm allen bolt on top (might need to shock it loose with air tools) and then when that bolt is loose you can jack the car up without needing spring compressors. the rest of the mounting bolts at the bottom you can loosen afterwards. fitting is reversal.

Sep 10, 2010 | 1994 Volkswagen Golf

1 Answer

How to change Shocks on 2001 Golf


My procedure removing front shocks:

  • Before I raise the car and place on jack stands, I loosen the top nut on the strut bearing. If you don't have an air gun to remove the nut there are tools available from online tool shops. A 1/2" drive breaker bar is attached on top of the tool while an allen wrench seen in the middle counter acts the by holding the strut in place.

0fd0977.jpg

Tool without the allen to use as a counter act, used with a regular L allen wrench.
4a1937f.jpg

  • Remove bolts that secure the swaybar to the control arm.
  • Use this tool to remove the tie rod ball joint with this tool.f1c8d52.jpg
  • With a automatic center punch tool, mark three reference points on the lower control arm ball joint flange (not on control arm. This will help line up the ball joint to the control arm without messing alignment putting back together.
  • Remove the 3 bolts that secure the ball joint to the control arm and wiggle out the ball joint and the wheel bearing housing away from the control arm.
  • Remove the large bolts that secure the strut to the wheel bearing assembly, this will somewhat loosen the hold on the strut.
  • With a long pry bar or a long pipe wedged on the control arm, position it when the time comes you need to counter act downwards.
  • On the wheel bearing assembly where the strut is buried, there will be a slot which you need a 1/4" drive extension attached to a 1/4" ratchet wedged into the slot.
  • Crank the ratchet slowly until it spreads the slot securely and wide enough to release the strut assembly.
  • With the strut separated from bearing assy. secure the strut from dropping and loosen the top nut above the strut bearing, remove strut from vehicle.
I don't know how far you want assistance but if need further info just let me know.

May 27, 2010 | 2001 Volkswagen Golf

1 Answer

Front wheel bearing 1986 Golf


Mount the tool on the wishbone and extract wheel bearing. Application example: ...... KL-0215-410 Press Tool Kit VW Golf III without Hydraulic Cylinder

Jun 28, 2009 | 1986 Volkswagen Golf

1 Answer

VwCabrio humming noise


Did you replace one front bearing or both? It could be the other front wheel bearing.

May 17, 2009 | 1996 Volkswagen Golf

1 Answer

Golf mk3 pulls to the left


First check your tyre pressures.If they check out ok, try wheel alignment.The fact that your steering wheel does not centre may mean its had new track rod ends or steering rack and hasn,t been aligned properly.

Apr 01, 2009 | 1996 Volkswagen Golf

1 Answer

Noise


IF THE NOISE IS IN THE FRONT AND ONLY WHEN WHEELS ARE TURNING AND THE GRINDING NOISE CHANGES WHEN TURNING LFT. OR RGHT. COULD BE FRONT WHEEL BEARING..OR CV JOINT..

Mar 12, 2009 | 1996 Volkswagen Golf

Not finding what you are looking for?
1994 Volkswagen Golf Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...