Question about 1986 Oldsmobile Toronado

1 Answer

I cant get the broken wheel studs out - 1986 Oldsmobile Toronado

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

As all or most wheel studs are pressed into hub,if you are taking them out with hub still on car,usually a good wack with hammer on stud works (with a second hammer behind hub to take up the shock,works great,as long as ure not re-using studs,if hubs are off of the car use a vise and hammer to remove and flip hub over to re-install new studs

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front lug stud nut on a 2006


jack up car ,remove front wheel ,brake caliper, and rotor, so now you have just studs and backing plate ,with a hammer and punch , drive out broken stud and go to your local parts store with broken part an and lug nut for that wheel, this is the hard part put new stud in hole that you punched the broken one out of and drive it in with a hammer or if you have a stud driver ,as far as it will go ,don't worry if you cant seat it all the way ,when you reassemble everything back on when you tighten lug nuts it will seat it the remander of the way ,BE SURE TO RETORQUE IT AFTER A SHORT DRIVR 20-30 MILES AND RE CHECK IT AT DIFFERNT INTERVlLES to make sure it's seated and tight. ok that's it in a nut shell ,hope this gets it done for you .good luck .
Woody ,

Aug 30, 2014 | Cars & Trucks

1 Answer

2006 dodge caravan with rear draum brakes. Broken wheel stud on right rear wheel. Got the drum off, got the broken stud off. but i cant get the new stud in. not enough space to get the new stud in. Is...


Make sure all tires are chalked,put vehicle in neutral,turn drum till it has a clear spot to knock stud out,use hammer and wooden block,don't use metal punch,can cause burr on end of stud and not want to come out of hole.Both tires on back may need lifted in air to turn.

Jul 05, 2017 | 2006 Dodge Grand Caravan

1 Answer

Broken wheel stud right rear wheel with drum brakes on 2006 dodge caravan. Cant get the new stud to go in. I dont have enough room for the stud to go in. Do i need to remove the wheel bearing? What will be...


To remove the broken stud use a punch and drive it out with a hammer back towards the backing plate. BY turning the axle around you will find a position or you may have to remove a brake shoe to help with the installation of the new stud. When you have it in place use larger nuts and pull it into place with the stud nut.. You may not be able to simply put the stud straight in but may have to start a bit of an angle and turn the axle to allow the stud to feed in.

Sep 01, 2013 | 2006 Dodge Grand Caravan

1 Answer

How to change broken wheel stud on 2007 ford escape


Some just pound out of the rotor. Take wheel off and then see if you cant drive out broken stud with a hammer. Usually this is how it's done and then you can drive a new one in the back side.

Dec 31, 2011 | 2006 Ford Escape

1 Answer

How to replace broken stud of honda crv 2001 front wheel


remove wheel, brake assembly & rotor. rotate to where the broken stud is in the opening where the brake assembly was. drive the broken stud out of the hub flange. then install the new stud by stacking washers on the new stud and tighten the lug till it pulls the new studs flange tight against the back side of the hub. remove lug and washers , reassemble .

May 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

Right side front broaken wheel lug


YOU CAN PRESS OUT BROKEN LUG STUD WITH STUD REMOVAL TOOL AND INSTALL A NEW STUD.THE TIRE SHOP WILL FIX IT.WONT COST THAT MUCH.IF YOU DONT HAVE RIGHT TOOL YOU CAN DAMAGE WHEEL BEARING IF YOU HAMMER ON BROKEN STUD.

Oct 11, 2010 | 1998 Acura RL

2 Answers

2000 Dodge Caravan....broken wheel studs...


Yeah , it's a fairly simple repair, All the wheel studs must be replaced and lug nuts also.Closely examine the wheel or get competent tyre replacement company to double check for damage ! Remove the brake disc caliper and brake disc itself (usually 2 cross head screws) , tap off (gently) it may be stuck thru corrosion / rust etc , Broken studs can be knocked out(towards drive shaft ) of the hub assy with a suitable drift and hammer (splined into hub) . The studs are a servicable replacement part. Check all other wheel nuts as this is usually a result from poor fixing or wheel replacement recently .. Good luck

Apr 05, 2010 | 2000 Dodge Caravan

1 Answer

Broken wheel studs


Hello there:
Normally these studs are pressed in by a machine
If you get a sledge hammer and a solid iron bar you can use this to get them off it takes a lot of doing but they will come off you may cioncider soaking the studs in penetrating oil for about 15 to 20 min before you attempt to get them off due to rust and build up.
If this does not work i would take the wheel to a shop that has a press ands have them get them off and have the new ones pressed in
Also You can heat the area around the stud with a torch and then use the sledge hammer ok ?
If you have the new studs and they are the right ones great, if not a local wheel or place that does rims should have them they cost around $2.00 a piece Ok?
Hope this is very helpful for you
Best regards Michael

Mar 14, 2010 | 2001 Nissan Xterra

3 Answers

Broken stud on wheel


The studs press out and in. Perhaps a hammer would work. Replacements studs can be purchased. Need to remove hub, of course.

Aug 13, 2009 | Hyundai Motor 2003 Elantra

2 Answers

Broken wheel studs on 1996 grand am se- passenger front


usually they are an assembly but when i get crazy and damage studs i raise and support both front wheels so i can turn them and slowly move the hub where you can fit teh stud in and use an open lugnut to tighten down it will pull the stud in (i use an air compressor for this)

Apr 28, 2009 | 1996 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...