Question about 2007 Hyundai Sonata Limited Sedan

1 Answer

How can I replace the front wheel studs on a Hyundai sonata 2003?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 566 Answers

Hi if you look at the new stids you are going to fit? you will see they are splined on the inner side so with wheel off you tap the old stud/s backwards from the hub then fit new stud/s from the rear ensuring located on splines then you can draw fully home into hub using w/nut or another nut same thread ? if your cars nuts are not open ended ?

Posted on Oct 03, 2009

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 22 Answers

SOURCE: 2003 hyundai elantra gls front wheel stud broke

grab a large punch and hammer and knock out the old broken one. Push the new one in and re tighten. This will pull it into place and because it has splines it should not spin while doing so.

Posted on Jun 10, 2009

Testimonial: "excellent advice"

keemo68
  • 1263 Answers

SOURCE: 2003 hyundia sonata made before 2/2003

you should be able to get replacement parts at Napa or Oreillys they a fairly in expensive. but only if the are the drive in kind, meaning you need to take a hammer to knock them out of the rotor assembly then you just take a drift pin/punch and hammer them back in. hope this is helpful. please rate this solution. thanks

Posted on Aug 30, 2008

  • 850 Answers

SOURCE: need to replace wheel stud on hyundai sonata, how?

remove the wheel & disc brake!
jst hit the stud very SMARTLY! with a good weighted hammer & it shoul fly straight out!
replace with new one by pushing it in the hole & use washers & the nut to pull it through !
then rplace every thing else!
Cheers Rob

Posted on Aug 15, 2009

Testimonial: "Thanks!! I am just a girl that doesnt know anything and that was my first thought!!"

cris_p
  • 62 Answers

SOURCE: wheel stud removal, (front)

usally u bang it firt with a hammer then u have to get a special tool from your aouto part store (u can rent it) and then just take them off

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove front wheel studs on sonata 2006


You can't remove the wheel studs totally out of the disc. It depends on how it is fitted.

Remove the wheel and check the brake disc. you can find the studs may be press fitted or welded to the brake to hold it in position & not to rotate when we tighten the bolts. Better approach nearest dealer to check it out and fix it

Jun 05, 2010 | 2006 Hyundai Sonata

1 Answer

Wheel stud removal, (front)


usally u bang it firt with a hammer then u have to get a special tool from your aouto part store (u can rent it) and then just take them off

Feb 08, 2010 | 2006 Hyundai Sonata

1 Answer

Front wheel stud replacement for a 2006 Hyundai Sonata GL.


grind a flat spot on the round head of the new stud this should give enough clearance to install it. don't pull the hub this will damage the bearing.

Oct 24, 2009 | 2006 Hyundai Sonata

1 Answer

How to replace front wheel bearing 2009 Sonata


No way ,its a strip the the whole hub unit off and there is a circlip coming in from the back ,which is the way the bearing is pushed out ,NO HAMMERS

Oct 23, 2009 | 2006 Hyundai Sonata

2 Answers

Need to replace wheel stud on hyundai sonata, how?


have a 2005 hyudai tucson can't remove the front studs even though we pulled off the brakes and caliper but still not enough room to put in new studs and i can't dissasemble it any further

Aug 15, 2009 | 2002 Hyundai XG350

1 Answer

I need to remove front r/side studs on 2005 hyundai elentra 4 dsd?


dear friend-replacing the stud is a fairly intensive job,the hub must be removed,so you might have to replace the wheel bearing,you will need special tools to attemp this job.

Jul 12, 2009 | 2007 Hyundai Sonata Limited Sedan

2 Answers

2003 hyundai elantra gls front wheel stud broke


grab a large punch and hammer and knock out the old broken one. Push the new one in and re tighten. This will pull it into place and because it has splines it should not spin while doing so.

Apr 05, 2009 | Hyundai Motor 2003 Elantra

2 Answers

NEED TO REMOVE REAR ROTOR


Take off the wheel, remove the brake caliper (2 bolts on the back), then the rotor just slides off, the wheel studs are part of the hub assembly not the rotor.

Nov 21, 2008 | Hyundai Motor 2002 Sonata

1 Answer

2003 hyundia sonata made before 2/2003


you should be able to get replacement parts at Napa or Oreillys they a fairly in expensive. but only if the are the drive in kind, meaning you need to take a hammer to knock them out of the rotor assembly then you just take a drift pin/punch and hammer them back in. hope this is helpful. please rate this solution. thanks

Aug 30, 2008 | Hyundai Motor 2003 Sonata

1 Answer

Replacing rear wheel bearings on 1999 hyundai sonata


  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Jul 19, 2008 | 1999 Hyundai Sonata

Not finding what you are looking for?
2007 Hyundai Sonata Limited Sedan Logo

531 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...