Question about 1996 Ford Ranger SuperCab

2 Answers

How do i remove c clips in 7.5 ford ranger rear axle

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 21 Answers

Remove the inspection plate. turn the axles until you can remove the center pin in the carrier. remove pin,rotate axles, remove spider gears, and push axle in towards center of truck, booya, pins should fall right out

Posted on Dec 20, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,489 Answers

Best method is to buy a pair of c-clip pliers which are designed for that purpose. Maybe Pep Boys or similar?

Charlie

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove rear axle from 1995 ford ranger 2 wheel drive need to replace oil seal


Raise the vehicle and properly support it. Remove the wheel and drum. Remove the rear diff cover, have a drain pan underneath to catch the gear oil. Place the trans in nuetral, chalk the front wheels to keep vehicle from moving if you forget to put it back into park befor you lower the vehicle. Rotat the differential until you see the bolt that holds the diff pin in place. Remove the bolt, 5/16 or 8 mm I believe. You can then remove the diff pin, do not rotate the diff with the diff pin removed! Push the axle in, you can then remove the C-clip that holds the axle to the side gear, it will usuall drop or just fall out. Pull the axle out of the rear diff and replace the seal. Put everything back together. Use black or grey RTV to reseal the diff cover making sure o clean up both surfaces as best you can. Put trans in park. Lower the vehicle. Remove the fill plug from the side of the differential and fill with gear lube until lube comes out the hole. Reinstall the plug and your good to go. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Mar 15, 2012 | 1995 Ford Ranger Supercab

1 Answer

Replacing rear axle bearings on a95 f150 not sure if i how to remove axle clips


Once you remove the pin from the spider gears you can push the axles in, remove the clips and pull the axles out.

May 11, 2011 | Ford F-150 Cars & Trucks

1 Answer

How do you remove an axle on the right rear of a 1999 explorer? it has a leaking wheel seal.


1. Drain diff if it has a plug.
2. Remove rear cover
3. Undo cross pin bolt and slide the cross pin out of the carrier
4. Push axle shaft in so you can remove the C clip
axle retainers
5. Slide axle out of housing.
6. Remove axle seal and then replace axle seal
7. Reverse steps

May 25, 2010 | 1999 Ford Explorer

1 Answer

How too remove rear axel horsehoe clips too remove axel?


In order to remove the axle, you need to go in through the rear pumpkin. Take the back plate off the rear pumpkin, then you will see where your axle comes in through the sides. Go back to the outer end of the axle, (where the tire goes) and push inward on the axle. It shouls move in about 1/2" or so, just enough to remove the clip. The clip should fall out easily if it is turned in the 'down' position. Then you will need to remove the pins that run through the axles themselvs, and the axles should pull right out to the sides.

Apr 06, 2010 | 2004 Ford F150

1 Answer

How do i change the rear wheel bearing in 1988 ford ranger


you need to remove the rear axle so you need to open the differential, You should go buy a book so you install the brake system correctly. At home plan on a 5 hour job at least.

Feb 25, 2010 | 1988 Ford Ranger

1 Answer

Rear axle seal is leaking on 04 heritage model,does this rear end have same c-clip to remove axle as older models?


Should be same, just don't forget differential bolt and pin removal first to allow you to push axle in to remove "C" clip.

Oct 25, 2009 | 2004 Ford F150

1 Answer

How to remove S-shaped clip holding both axles together and c-clip in the rear differential of a 2000 ford crown victoria.


remove rear cover ! make sure car is in neutral! ok spin the ring gear and locate the 8 mm bolt remove this bolt then slide the pin out ! now go to which ever side ur removeing and push the axl in! the c clip will fall out

Oct 18, 2009 | 2000 Ford Crown Victoria

1 Answer

How do you remove c-clips on axle of 95 ford rear end?


If you have already removed the outer axle bearing cover in the rear hub, try popping the axle out as some of them have a compression clip holding it in place in the differential. If it doesn't pop loose, you wil have to remove the differential cover and push the axle inward enough to access the retaining clip to remove it. It should slide out fairly easile once the axle is pushed in far enough to clear the retainer clip lock collar.

Aug 17, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

How to change coil spring on 1994 ford ranger


RAISE AND SAFELY SUPPORT VECHICLE.PLACE A SUPPORT UNDER THE REAR AXLE.REMOVE NUTS AND BOLTS ATTACHING THE SHOCK ABSORBER TO THE RADIUS ARM.REMOVE THE NUT SECURING THE SPRING TO THE AXLE AND REMOVE THE RETAINER.SLOWLY LOWER THE AXLE TO RELIEVE THE SPRING TENSION.REMOVE THE SPRING BY ROTATING THE UPPER COIL OUT OF THE TABS IN THE UPPER SPRING SEAT - TO INSTALL.INSTALL. THE TOP OF THE SPRING IN THE UPPER SEAT.ROTATING INTO POSITION.RAISE THE AXLE UNTIL SPRING IS SEATED IN THE LOWER SPRING SEAT.INSTALL THE LOWER RETAINER AND TIGHTEN THE NUT TO 70 - 100 FT LBS .THEN CONNECT THE SHOCK ABSORBER TO THE RADIUS ARM AND LOWER THE VECHICLE.

Aug 01, 2009 | 1994 Ford Ranger Supercab

Not finding what you are looking for?
1996 Ford Ranger SuperCab Logo

Related Topics:

343 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...