Question about 2000 Volkswagen GTI

1 Answer

What holds the cv joint on to the driveshaft on a 2000 model golf gti

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Volkswagen Master
  • 76,846 Answers

There is a snap ring down inside the end of the axle, clean all the grease out to see it.

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove axle from front of 1998 windstar


  1. Raise and support the vehicle safely.
  2. Remove the front wheels.
  3. Insert a steel rod into the brake rotor to prevent the rotor from turning and loosen the axle wheel hub nut. Discard the nut.
  4. Remove the ball joint-to-front wheel knuckle retaining nut. Drive the bolt out of the front wheel knuckle using a punch and hammer.
  5. Remove the front brake anti-lock sensor and position it out of the way.
  6. Separate the ball joint from the front wheel knuckle using a prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing.
Use care to prevent damage to the front wheel driveshaft joint boot.
  1. Remove the stabilizer bar link at the front stabilizer bar.
Make sure the CV-joint puller does not contact the transaxle shaft speed sensor. Damage to the sensor will result.
  1. Install a CV-Joint Puller (T86P-3514-A1) or equivalent between the inboard CV-joint and the transaxle case.
  2. Install a CV-Joint Extension (T86P-3514-A2) or equivalent into the puller and hand-tighten.
  3. Using an impact slide hammer, remove the driveshaft from the transaxle.
Do not allow the front wheel driveshaft and joint to hang unsupported. Damage to the front wheel driveshaft joint may result. Do not wrap wire around the front wheel driveshaft joint boot. Damage to the boot may result.
  1. Support the end of the driveshaft and joint assembly by suspending it from the chassis using a length of wire.
Never use a hammer to separate the outboard front wheel driveshaft joint from the wheel hub. Damage to the outboard front wheel driveshaft joint threads and internal components may result.
  1. Separate the outboard front wheel driveshaft joint from the wheel hub using a Front Hub Remover/Replacer (T81P-1104-C) or equivalent. Make sure the hub remover adapter is fully threaded onto the hub stud.
Do not move the vehicle without the outboard CV-joint properly installed, as damage to the bearing may occur.
  1. Remove the front wheel driveshaft and joint assembly from the vehicle.
To install:
Do not reuse the retainer circlip. A new circlip must be installed each time the inboard CV-joint stub shaft is installed into the transaxle differential.
  1. Install a new retainer circlip on the inboard CV-joint stub shaft by starting one end in the groove and working the retainer circlip over the inboard shaft housing end and into the groove. This will avoid overexpanding the circlip.
A non-metallic mallet may be used to aid in seating the retainer circlip into the differential side gear groove. If a mallet is necessary, tap only on the outboard CV-joint stub shaft.
  1. Carefully align the splines of the inboard CV-joint stub shaft housing with the splines in the differential. Exerting some force, push the inboard CV-joint stub shaft housing into the differential until the retainer circlip is felt to seat in the differential side gear. Use care to prevent damage to the inboard CV-joint stub shaft and transaxle seal.
  2. Carefully align the splines of the outboard front wheel driveshaft joint with the splines in the wheel hub, and push the shaft into the wheel hub as far as possible.
  3. Temporarily fasten the front disc brake rotor to the wheel hub with washers and two lug nuts. Insert a steel rod into the front disc brake rotor and rotate clockwise to contact the front wheel knuckle, to prevent the front disc brake rotor from turning during front wheel driveshaft and joint installation.
A new front axle wheel hub retaining nut must be installed.
  1. Manually thread the front axle wheel hub retaining nut onto the outboard CV-joint stub shaft housing as far as possible.
A new bolt and nut must be used to connect the front suspension arm to the knuckle.
  1. Connect the front suspension lower arm to the front wheel knuckle. Tighten the nut and bolt to 40-55 ft. lbs. (54-74 Nm).
  2. Install the front brake anti-lock sensor.
  3. Connect the front stabilizer bar link and tighten to 35-45 ft. lbs. (47-65 Nm).
Do not use power or impact tools to tighten the hub nut.
  1. Tighten the front axle wheel hub retaining nut to 157-212 ft. lbs. (213-287 Nm).
  2. Install the front wheels and lower the vehicle.
  3. Using the recommended type of fluid, fill the transaxle to the proper level.

Jul 07, 2014 | 1998 Ford Windstar

1 Answer

I have a golf gti automatic. It makes a grinding when comming to stop and when frewheeling at low speed. i've checked brake pads and there fine


cv joint going bad, grease and boot may fix, probably caused by a cracked cv boot, and now the grease is gone, first thing to check is the boot on the cv joint (that's the shaft/joint that turns the wheels)attatches by a single nut in center of your front wheel (outer joint) if not the outer, then ck the inner (attatches to the transmission) (inner joint). most likely is the outer joint though

Sep 04, 2012 | Volkswagen GTI Cars & Trucks

1 Answer

How do i remove driveshafts


We'll do one side of the car and you can repeat the steps on the other side, before you remove the wheels you have to remove the large centre nut that holds on the cv joint. the nut is in the centre between the wheel nuts, its normal a 34'' or 36'' you'll have to us a power bar as they can be tight. once the nut is removed, jack the car up and remove the wheel, next you have to remove the nut holding the (bottom) ball joint, when the nut is off the ball joint will be hard to seperate hit the ball joint on all sides with a hammer if it still wont move you will have you use a ball joint seperater (fork shape) to brake the connection. once the ball joint is removed you can (tap) the the cv joint out of its housing in the centre of the wheel( where the big nut was ) be careful not to damage the treads. with the cv joint free the driveshaft will hand free some off them just pull out when you remove the clips on the rubber booth attached to the driveshaft and gearbox, others booths are bolted in with small 13mm bolts, repeat the process on the other side. good look I hope this helps (Rate me answer please)

Aug 30, 2010 | 2000 Volkswagen Golf

1 Answer

Unable to remove strut with lower arm in place and driveshaft connected to hub.Ifollowed Haynes Golf manual procedure but found space too tight to remove strut even with spring compressed.Eventually...


The swaybar is still giving you tension. The link has to be disconnected to the control arm. You need to disconnect the balljoint for the tie rod. Before removing the lower ball joint from the hub assembly, mark with a punch for reference when putting it back. There is no need to remove the center nut for CV joint unless it is the original strut which is longer when in static position. Note; DO NOT roll vehicle on the ground without a CV joint connected to the hub, wheel bearing will be crushed from vehicle weight.

You can use a 1/4" extension end placed on the slot to spread the strut carrier wide enough to release the strut from the carrier.

May 04, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

I used a Haynes VW Golf manual to renew a front suspension coil spring on my 2003 Seat Leon but found removal of the strut almost impossible with the lower arm in position.I have now managed to damage the...


Disconnect the front sway bar linkage from the control arm. Disconnect the steering ball joint and lower control arm ball joint then and only then you will have elbow room work around once you have removed the axle nut from the CV joint. Sorry no short cut for this procedure, some even disconnect the control arm from the car to persuade the removal.

May 04, 2010 | 2003 Volkswagen Golf

2 Answers

Need to change cv outer boot on mazda ba 94 model.


it just pulls out. it hasa circlip that holds it in on driver side. which side?

here's an escort, should be similar. note step 17

Removal
  1. Raise and support the vehicle.
  1. Remove the lug nuts (1012) and the front wheel and tire assembly.
  1. Remove the front fender splash shield bolts and the front fender splash shields (16103) .
  1. Use a small cape chisel to carefully raise the staked portion of the front axle wheel hub retainer (3B477).




  1. Remove the front axle wheel hub retainer and discard it.
  1. Remove the cotter pin and the tie rod end nut from the tie rod end (3A130). Discard the cotter pin.




  1. Use an appropriate tie rod end remover to separate the tie rod end from the front wheel knuckle (3K186).




  1. Remove the ball joint bolt and the ball joint bolt nut.




  1. Carefully pry down on the front suspension lower arm (3078) to separate the front suspension lower arm ball joint (3050) from the front wheel knuckle.




  1. Pull outward on the front wheel knuckle (3K185). Carefully pull the front wheel driveshaft and joint from the front wheel knuckle and position it aside.




  1. NOTE: Removal of the LH front wheel driveshaft and joint (3B437) requires removal of the transmission support crossmember (6A023) to allow access with a pry bar. If the LH front wheel driveshaft and joint is being removed, continue with step 11. If the RH front wheel driveshaft and joint is being removed, continue with step 15.

    Support the transaxle with a transaxle jack or equivalent.
  1. Remove the four transaxle mount-to-rear engine support nuts.




  1. Remove the two rear engine support nuts at the rear of the transmission support crossmember.
  1. While supporting the rear of the transmission support crossmember remove the two rear engine support bolts. Remove the transmission support crossmember.




  1. Position a drain pan under the transaxle.
  1. Insert a pry bar between the front wheel driveshaft and joint and the transaxle case.
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Extreme care must be taken to ensure that the pry bar does not damage the transaxle case, the transaxle oil seal, the front wheel driveshaft and joint, or the front wheel driveshaft joint boot (3A331).
    Gently pry outward to release the front wheel driveshaft and joint from the differential side gears (4236).




  1. Remove the front wheel driveshaft and joint.




  1. stf~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When the LH and RH front wheel driveshaft and joint assemblies are removed, Transaxle Plugs T88C-7025-AH must be inserted to prevent the differential side gears from becoming mispositioned. If the gears become misaligned, the differential will have to be removed from the transaxle to align the gears.
    If both front wheel driveshaft and joints were removed, install Transaxle Plugs T88C-7025-AH in the differential side gears.
  1. Remove and discard the driveshaft bearing retainer circlip (3Z498).

Oct 03, 2009 | 1994 Mazda 323

1 Answer

How do I change the CV joints on a 1.8TD Ford Escort P reg


Hi mate

With the driveshaft removed from the vehicle.

Undo the the retaining straps on the CV boot.

Pull the CV boot up the driveshaft a little way, enough so you can clean all the old grease away.

Now look into the CV joint an locate the circlip that locks the CV to the driveshaft.

Now put the driveshaft into a vice with the CV joint facing downwards.

Now open the circlip and at the same time strike the CV joint. You can do this with a ballpin hammer if you are scrapping the CV joint. You can get a helper to stike the CV joint with a hammer while you keep the circlip open.

This will release the CV joint form the drive shaft.

Now clean the driveshaft of any old grease and fit a new CV boot if needed.

Now reverse the driveshift in the vice and fit the new CV joint. It will tap on with no trouble but do not damage it. Test it is on by trying to pull it off with your hands.

Now fill it with new grease.

Fit the CV boot to the CV joint and secure it to the CV joint.

Now it is ready to refit to your vehicle.

I trust this solves the problem for you.

Ray


Sep 08, 2009 | 1998 Ford Escort

1 Answer

Noise


IF THE NOISE IS IN THE FRONT AND ONLY WHEN WHEELS ARE TURNING AND THE GRINDING NOISE CHANGES WHEN TURNING LFT. OR RGHT. COULD BE FRONT WHEEL BEARING..OR CV JOINT..

Mar 12, 2009 | 1996 Volkswagen Golf

Not finding what you are looking for?
2000 Volkswagen GTI Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...