Question about Chevrolet Silverado 1500

1 Answer

How to align timing marks on gears of 1992 chevy truck with a 350 5.7 engine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,982 Answers

Mark on cam gear points straight down, one on crank gear points straight up directly at the one on cam gear.

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1998 chevy metro timing marks


alldata d o t c om , its all there for $15

same at Mitchell.but more bread.

Aug 05, 2013 | 1992 Geo Metro

1 Answer

How to fix the trailblazer 2004 4.2l engine timing chain


Its the same as a chevy v8 pull radeator fan water pump lower crank pully loosen oil pan bolts align timing marks crank mark at 12 oclock cam cshaft mark at 6 oclock replace with new gears and chain timing cover gasket crank seal and water pump gaskets

Jun 26, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

Timing chain gear marks 92 f150 300c.i


Removal
  1. Drain the cooling system and crankcase.
  1. Remove the engine front cover (6019). Refer to Engine Front Cover in the In-Vehicle Service portion of this section.
  1. Check the camshaft end play, the timing gear backlash and the timing gear runout. Refer to Section 03-00 .
  1. Crank the engine until the timing marks are aligned as shown.


9d1eda0.gif

Aug 19, 2010 | 1992 Ford F150 SuperCab

1 Answer

How to replace timing belt on a 1992 pontiac sunbird


1989–92 VEHICLES
  1. Disconnect the negative battery cable.
  2. Remove the serpentine belt and timing belt cover.
  3. Loosen the water pump bolts and release tension with tool J–33039 or equivalent.
  4. Raise and support the vehicle safely.
  5. Remove the crankshaft pulley.
  6. Carefully lower the vehicle, then remove the timing belt. Fig. 11: Exploded view of the timing belt assembly — 1989–92 OHC engines 87953118.gif
    To install:
  7. Turn the crankshaft and the camshaft gears clockwise to align the timing marks on the gears with the timing marks on the rear cover.
  8. Install the timing belt, making sure the portion between the camshaft gear and crankcase gear is in tension.
  9. Using tool J–33039 or equivalent, turn the water pump eccentric clockwise until the tensioner contacts the high torque stop. Tighten the water pump screws slightly.
  10. Turn the engine by the crankshaft gear bolt 720°to fully seat the belt into the gear teeth.
  11. Turn the water pump eccentric counterclockwise until the hole in the tensioner arm is aligned with the hole in the base.
  12. Tighten the water pump screws to 18 ft. lbs. (24 Nm), while checking that the tensioner holes remain as adjusted in the prior step.
  13. Install the crankshaft pulley, timing belt cover and the serpentine drive belt.
1993–94 VEHICLES
  1. Disconnect the negative battery cable, then partially drain and recover the cooling system.
  2. Remove the coolant recovery reservoir.
  3. If equipped, remove the A/C belt.
  4. Remove the serpentine belt.
  5. Disconnect the evaporative emission pipe assembly.
  6. Remove the crankshaft pulley assembly.
  7. As outlined earlier, remove the timing belt front cover.
  8. Align the marks on the crankshaft sprocket with the marks on the rear timing belt cover by rotating the crankshaft.
  9. Loosen the water pump retaining bolts, and release the tension with tool J 33039-A or equivalent.
  10. Carefully lower the vehicle, then remove the timing belt. Fig. 12: Timing belt installation and tightening specifications — 1993–94 2.0L OHC engines 87953119.gif
    To install:
  11. Turn the crankshaft and camshaft gears clockwise to align the timing marks on the gears with the timing marks on the rear cover.
  12. Install the timing belt, making sure that the portion between the camshaft gear and crankshaft gear is in tension.
  13. Using tool J 33039-A, or equivalent adjustment tool, turn the coolant pump eccentric clockwise until the tensioner arm contacts the high torque stop. Tighten the water pump screws slightly.
  14. Turn the engine by the crankshaft gear bolt 720°clockwise to fully seat the belt into the gear teeth.
  15. Turn the coolant pump eccentric counter clockwise until the hole in the tensioner arm is aligned with the hole in the base. This must be done with the engine at room temperature, approximately 68°F (20°C).
  16. Tighten the water pump screws while checking that the tensioner holes remain as adjusted as in step 15.
  17. As outlined earlier, install the timing belt cover.
  18. Install the crankshaft pulley.
  19. Connect the evaporative emission pipe assembly.
  20. Install the serpentine drive belt and the A/C belt (if equipped).
  21. Install the coolant recovery reservoir.
  22. Properly fill the cooling system, then connect the negative battery cable.
prev.gif next.gif

Aug 11, 2010 | 1992 Pontiac Sunbird

1 Answer

Timing chain marks


Timing chain marks are marks made by the factory on the gears. These marks should be aligned in the proper array in order to achieve proper timing. Often times there are coinciding marks on the block behind the gear to which to align.

Aug 01, 2010 | 1992 Saturn SL2

1 Answer

Need timing marks for 350 94 chevy


if you mean on gears? they align pointing at each other directly, meaning top dot is down and bottom dot is straight up

May 21, 2010 | 2000 GMC New Sierra 1500

1 Answer

Need firing order and timing marks for a 95 chevy v6


1995 Chevrolet S10/T10 P/U 2WD 4.3 liter V-6 VIN "W"

Fig. 1 Firing Order
65f2f9e.gif


Fig. 2: Timing mark alignment-4.3L engine
d0e0833.gif

I hope helps with this. Good luck.

Dec 29, 2009 | 1992 Chevrolet S-10

4 Answers

1992 Volvo 960 Broken timing belt - need to locate alignment marks for crankshaft and camshaft and associated reference marks for TDC or other position. Car was cranked AFTER belt broke - Crankshaft Is...


IF U BROKE THIS BELT WHILE DRIVING U HAVE BENT THE VALVES IN THE ENGINE, THIS IS WHAT IS CALLED AN INTERFERENCE DESIGN ENGINE, THAT MEANS WHEN THE TIMING BELT BREAKS THE PISTONS HIT THE ENGINES VALVES

Nov 11, 2009 | 1992 Volvo 960

1 Answer

What are the timing gear specifications for 1992 Honda Accord 2.2L. am replacing the timing belt and gear & need to align timing marks. thanks


manualy turn the engine over to the first cylinder. (place screwdriver in cylinder through spark plug hole) when the pistion is all the way up that is top of cylinder #1 . at this point ther should be marks on the gears and on the block that align. if not than mark them your self with a paint marker. now loosen the tensioner to remove belt, and install new belt. be careful that all marks are still aligned that is a zero clerance engine. meaning that being one tooth off will colaps a valve.

Aug 15, 2009 | 1991 Honda Accord

1 Answer

Setting the timing in a 1993 subaru justy


If you are talking of the rubber timing belt setting then rotate the cam gear till the timing mark (small hole) on the camshaft gear aligns with the mark on the plastic cover behind it. Mark is on top of plastic cover (12 'o' clock).
Rotate the crank till the timing mark (groove, not the one for the crankshaft woodruff key) on crankshaft gear is aligned with the mark on the bottom of the plastic cover behind it. (6 'o' clock).
Tighten tensioner against timing belt rotate engine a few times make sure alignment of timing marks remain.

Dec 14, 2008 | 1992 Subaru Justy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...