Question about Ford E-350

1 Answer

Need to remove the alternator on a 96 E-350 - E-350 Ford Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

FIRST TURN OFF RADIO.SO YOU WONT LOSE CODE.DISCONNECT NEGATIVE BATTERY CABLE.DISCONNECT THE ELECTRICAL CONNECTORS FROM THE ALTERNATOR.REMOVE THE ALTERNATOR DRIVE BELT.THEN REMOVE THE PIVOT BOLT AND ADJUSTING BOLT OR THE MOUNTING BOLTS.THEN REMOVE THE ALTERNATOR FROM THE ENGINE.REMOVE THE ALTERNATOR FAN SHIELD IF EQUIPPED.

Posted on Oct 03, 2009

  • Jonah Oneal Oct 03, 2009

    TORQUE MOUNTING BOLTS TO 30 - 41 FT LBS.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2012 genesis 8 cylinder alternator removal


you need a garage as you have to recover and disconnect the a/c refrigerant.

2010 alternator removal

then I found this

It's a little tricky.
I recently had to replace mine, it was still under warranty.

You don't have to removed any of the motor mounts.
A quick review of the process.

Release the pressure on the belt tensioner and remove
The belt around the alternator.
On the top left corner of the alternator you'll see a 10mm
Bolt bracket holding the alternator wires. Remove that 10mm bolt.
Then the alternator connector and power wire. A 12mm nut.
Then to remove the alternator you must remove the bracket which holds the alternator,
Which is the tricky part. The alternator has 2 14mm bolts holding it to the bracket, the bracket has 4 14mm bolts and
A 12mm bolt on the front. Two of the 14mm bolts are located behind the alternator.
Which means you would have to move the alternator toward the front of the car to reach the two bolts.
Then remove the bracket and alternator together. Then you would have to follow in reverse order to properly reach
Those 2 14mm behind the alternator.

It's going to seem like impossible especially your first time.
The Hyundai instruction just shows to remove the belt, under covers and the alternator. Literally.
I don't know where your located but I'm in Miami. If that's any help, we can do it together no issues.

Thread Need Help Does anyone have write up to replace alternator 2014...

remove alternator for 2012 4 6 genesis Google Search

Jul 25, 2017 | Cars & Trucks

1 Answer

How to remove the alternator from a 2002 chrysler sebring without discharging the ac


alternator in tight spot,you need to loosen remove brace bolts you need brace with alternator.remove alternator pivot bolt and spacer and adjustment nut and bolt,when you remove alternator you have to angle it out through bracket by the AC COMPRESSOR. YOU DONT HAVE TO DISCONNECT ANY AC LINES OR COMPRESSOR TO REPLACE ALTERNATOR.

Nov 27, 2012 | Cars & Trucks

1 Answer

Need to chage the alternator on 2005 ford escape, 2wd, v6, xlt. what do i need to remove, and how, in order to get the alternator out? axle? exhaust?


THE 3.0L ENGINE YOU NEED TO TURN OFF RADIO FIRST TO KEEP LOCKING IT OUT.REMOVE NEGATIVE BATTERY CABLE.REMOVE THE RIGHT SIDE INTERMEDIATE AXLE SHAFT. REMOVE RIGHT SPLASH SHIELD AND RETAINERS REMOVE DRIVE BELT THEN REMOVE THE ALTERNATOR.WHEN INSTALLING NEW ALTERNATOR TORQUE ALTERNATOR BOLTS TO 35 FT LBS.

Sep 07, 2011 | Ford Escape Cars & Trucks

2 Answers

Is fixing the ultinator yourself an easy job


  1. Disconnect the negative battery cable.
  2. Remove the drive belt.
  3. If necessary, remove any splash shielding for easier access to the alternator.
91072p19.gif

For easiest access to the alternator assembly, first remove the splash shield mounting fasteners ...
Click to Enlarge 91072p18.gif

... then swing it out of the way for access to the alternator assembly
Click to Enlarge 91072p17.gif

View of the alternator electrical connections-(A) battery positive, (B) field terminals, (C) wire harness hold down, (D) ground terminal

  1. Tag and disengage the alternator wiring.

It may be necessary to remove the alternator and mounting bracket from the vehicle as an assembly.

  1. If equipped, remove the front alternator assembly mounting plate.
91072p09.gif

Remove the six nuts and bolts that secure the front mounting plate to the alternator assembly
Click to Enlarge 91072p10.gif

Remove the front alternator assembly mounting plate from below the vehicle
Click to Enlarge

  1. Unfasten the alternator mounting and pivot bolts and remove the alternator.
  2. If installing the original alternator assembly, push out the pivot bushing as illustrated.
91072p11.gif

After removing the alternator assembly front mounting plate, remove the front engine-to-alternator bracket mounting stud
Click to Enlarge 91072p08.gif

Remove the two alternator bracket-to-engine mounting bolts
91072p12.gif

Remove the alternator and mounting bracket assembly from the vehicle
Click to Enlarge 91072p14.gif

If re-installing, the alternator has a pivot bushing on the pivot arm that should be pushed out before installation
91072p15.gif

Mount a C-clamp and 18mm socket on the alternator pivot bushing ...
91072p13.gif

... then compress the C-clamp until it pushes the alternator pivot bushing out

To install:

  1. Mount the alternator to the brackets with the nuts and bolts. Tighten the two mounting bolts and nuts to 40 ft. lbs. (54 Nm).
  2. If the alternator and mounting bracket were removed as an assembly, install the assembly into the vehicle.
  3. If removed, install the front mounting plate.
  4. Engage the alternator electrical connections.
  5. If removed, install the splash shield.
  6. install the drive belt and attach the negative battery cable.
  7. shinehutt_58.gifshinehutt_57.gifshinehutt_56.gifshinehutt_55.gifshinehutt_54.gifshinehutt_53.gifshinehutt_52.gifshinehutt_51.gif
the job is akward ive incl as much info you need to repair yourself

plz comment reply if need more info

Jan 20, 2011 | 1995 Jeep Grand Cherokee

2 Answers

How to change the Alternator on 2003 Ford Escape


Hi, the first thing you will need to do is disconnect the battery cable. then take a wrench and release the tension on the serpentine belt by using the wrench to turn the tensioner to release the tension. From expirience i would draw a diagram of the belt routing before removing it. after the belt is removed you will need to remove the power wire from the back of the alternator by removing the nut that holds it on, then remove the connector from the side or back. there are three bolts holding the alternator to the engine. they should be a 15 mm or a 13 mm. assembly is reverse of removal. good luck

May 19, 2010 | 2003 Ford Escape

1 Answer

I have a 2003 dodge neon sxt and i can locate the alternator but i dont see how to take if off please help


To remove the alternator you will need to raise the front of the car and block the rear wheels. Disconnect the negetive wire from the battery. Loosen the upper alternator adjustment boltnut. Remove the right front tire and the accessory drivebelt splash shield. Loosen the alternator lower mounting bolt. Remove the alternator drive belt and disconnect the electrical connectors from the alternator. Remove the upper and lower adjustment bolts and remove alternator. You will have to remove the alternator bracket when you lower the alternator down. Installation is the reverse of removal. Hope this will help you.

May 16, 2010 | 2003 Dodge Neon

1 Answer

How to remove the alternator


Before the step-by-step instructions I want to make sure this is the Alternator that needs to be replaced and not something else. This will save you money for an Alternator you don't need and save you time for replacing a good alternator.
Start the vehicle. With the engine running - disconnect the Negative Cable from the Battery. If the Engine dies - it is the Alternator. If it doesn't die - it is not the Alternator. I have had plenty of people who have replaced perfectly good Alternators only to find out it was something else.
Step-by-step:
1. Disconnect the Negative Cable from the Battery.
2. Using a 15mm closed end wrench/bar - Rotate the Belt Tensioner towards the front of the vehicle and remove the Surpentine Belt off the Alternator. You do not have to take it completely off the vehicle.
3. Remove the bolt holding the top of the Alternator Mounting Bracket to the Engine Intake.
4. Remove the bolts (plural) holding the outside of the Alternator Mounting Bracket to the Alternator Mounting Plate.
5. Remove the bolt holding the top of the Alternator to Alternator Mounting Bracket.
6. Remove the Alternator Mounting Plate.
7. Remove the the Altenator Mouting Bracket.
8. Rotate the Alternator towards the rear.
9. Discoonect the electrical connections (plural), including the nut holding the wire on.
10. Remove the lower Pivot bolt located at the bottom of the alternator.
11. Remove the alternator.
12. Installation is reverse of above.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Dec 15, 2009 | 1999 Plymouth Voyager

2 Answers

Alternator removal on 87 acura integra


you need to loosen and remove the alternator mounting bolts and remove the V - belt and alternator assembly.

Dec 05, 2009 | 1987 Acura Integra

1 Answer

Need to change the alternator


REMOVAL & INSTALLATION

3.3L Engine:
  1. Disconnect the battery negative - cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the mounting bolt.
  9. Remove the spacer & washer
  10. Remove alternator.
To install:
  1. Attachthe alternator to the support bracket. Tighten all bracket andalternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Connect the negative - battery cable.
-------------------------------------------------------------------------------------------------
3.5L Engine:
  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
  4. Loosen the belt adjusting bolt.
  5. Remove the alternator drive belt.
  6. Remove the bracket.
  7. Remove the lower mounting bolt and pivot bolt.
  8. Remove the alternator.
  9. Disconnect the alternator field circuit plug.
  10. Remove the B+ terminal nut and wire.
To Install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
If you need photos to follow then try this link...
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006a83e

Jan 20, 2009 | 1999 Dodge Intrepid

1 Answer

How do i replace the alternator on mazda mpv 2000?


Remove negative (-) battery terminal from battery. Remove drive belt from alternator pulley. Remove wiring harness (electrical connections) from alternator. Remove attaching bolts for alternator. Pry out alternator. Reverse steps to reinstall. 

Dec 23, 2008 | 2000 Mazda MPV

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...