Question about Ford F-350

2 Answers

I have a 1996 Ford F350, diesel,5- speed manual trans.The ring and pinion gear are bad in the differential.It has 410 stamped on the ring gear and the tag says 10.25.What are the procedures,torque settings,and adjustments on replacing the ring and pinion

Posted by on

  • jeffmiller90 Oct 03, 2009

    IS THERE NOT A PROCEDURE YOU CAN E-MAIL ME ON HOW TO DO THIS PROJECT BESIDES TELLING ME IT SHOULD GO SOME WHERE ELSE FOR REPAIRS?

  • jeffmiller90 Oct 03, 2009

    thank you. that was the info I was looking for.This will help alot

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 986 Answers

Here is a website that can help you... this is a pretty big job, make sure you have all the tools that you will need. Id also go and buy a Chilton Or Haynes manual for help. Best of luck

http://www.differentials.com/install.html

Posted on Oct 03, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 986 Answers

There is alot going on here,you have poinion to ring pattern that just comes from experence and you have a preload for your penion, and side load for your bearing I recamend that this is not a back yard job and not one for a first timer because parts are so high.you want everthing to be right.I hope this help you?

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Setting up the differential on my ford 8000 tractor


what build year
ford 8000 as a model covered a lot of years

Ford 8000 8600 9000 9600 Tractor Service Manual Manual Vault


TractorData com Ford 8000 tractor information

does the diff information setup have a shim chart ?

Differential lock:hydraulic



maxresdefault-vdftmprayiwrzc40uomd3tff-1-0.jpg

Apr 07, 2017 | Ford Cars & Trucks

1 Answer

Diagram on front drive shaft cv joint for 2000 for superduty


The Dana model 50 and model 60 front drive axles feature the following:
  • a hypoid gear design with the centerline of the pinion set below the centerline of the ring gear
  • a conventional differential case
  • full-floating axle shafts
  • a cast center section with two steel tubes
  • a stamped differential housing cover

0a7b4cbc-d39a-4f16-af80-f07177eb8ef0.gif
fba40cd0-7898-4953-b06e-43b49c5b6e1a.gif

Sep 25, 2014 | Ford Cars & Trucks

2 Answers

Why is the rear end making a whining noise


The whining noise could be for many reasons. Narrowing the possibilities depends on when the noise occurs. If it happens only while decelerating at any or all speeds is most likely caused by bad pinion bearings or loose pinion bearing preload. If it happens during acceleration over a small or large speed range is usually caused by worn ring and pinion gears.

One cheap thing to check is the fluid level in the differential. If low, topping off the lube may help for a while.

Jun 12, 2014 | 2000 Ford Mustang

1 Answer

Rear differential leaking on ford f-350 super duty


if you have never done one its best to take to dealer because you have to remove drive shaft and then rear pinion nut and remove seal the tricky part is you have to buy new crush sleeve and thats what sets your pinon depth so that pinion rides in middle of ring gear its called setting your pinion depth if over tighten will hurt bearings and or ring gear and if under tighten will be verry noisey and cause ring and pinion failure best to let someone with special tools and knows what thier doing i use to do all chevy diff at my old dealer your use inch torque wrench to measure the drag on pinion nut and then use 1/2 inch impack to tighten the nut people freak because impack is rated at 600 ft pds but your using inch torque wrench to check drag not how tight nut is good luck

Aug 23, 2012 | 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

I have a 2009 Mustang V8 with 5 speed manual transmission. In every gear except 4th, I have a high-pitched whine. Audible only on positive throttle. It's not real loud, just very annoying. The noise...


Hello, Also check the rear differential level as a Pinion gear can whine too! If you have a limited slip differential, there is an additive to use for the differential plates. You need to check your trans oil, but if it is at the top, makes noise, it is probably a mechanical problem.

I want to say a product called Lube Guard has a line of oils which help reduce noise. There are different formulas for steering, trans, differential and so forth.

I see you have a 2009 car. A Warranty can vary in age and mileage. Check with your Dealer about what you have for your car. It may all be a covered repair.

Jun 21, 2011 | Ford Mustang Cars & Trucks

2 Answers

Why is it when i turn the rear wheels lock up like a positive traction?


i would remove rear cover plate to axle ( pig ) and check for ring and pinion gear or spider gears for broken teeth. Or are you sure it's not a posi gone bad ? i would think that you have a problem with the pinion gear and or ring gear.

Apr 14, 2011 | 1996 Chevrolet C/K 3500

1 Answer

How do you know what ratio a subaru wrx gearbox is if it doesn't have a trans code sticker on it?


This information is from my genuine service manual. I hope it is of help.
Non-turbo
Turbo
Sedan Wagon
Type 5-forward speeds with synchromesh and 1-reverse
Transmission gear ratio
1st 3.454 3.454
2nd 2.062 1.947
3rd 1.448 1.366
4th 1.088 0.972
5th 0.780 0.738
Reverse 3.333
Front reduction gear Final
Type of gear Hypoid
Gear ratio 4.111 3.900
Rear reduction gear
Transfer
Type of gear Helical
Gear ratio 1.000 1.100
Final
Type of gear Hypoid
Gear ratio 4.111 3.900 3.545
Front differential Type and number of gear Straight bevel gear (Bevel pinion: 2, Bevel gear: 2)
Center differential Type and number of gear
Straight bevel gear
(Bevel pinion: 2, Bevel gear: 2 and viscous coupling)
Transmission gear oil GL-5
Transmission gear oil capacity 3.5 2 (3.7 US qt, 3.1 Imp qt)

Mar 21, 2010 | 2007 Subaru Impreza WRX Sport Wagon

1 Answer

Torque specs 7.5 inch rear axle 96 ford ranger


Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Jan 30, 2009 | 1996 Ford Ranger SuperCab

4 Answers

1996 Audi A4 Quattro has a noisy rear differential


It's the wheel bearing. Guaranteed. Just replaced mine. Go to Audiworld tech articles for step by step instructions on how to test the wheel bearings. They must have been put in wrong last time or they just went out again.

Oct 13, 2008 | 1996 Audi A4

1 Answer

Rear gear ratio for 93 toyota 4x4 pickup 5 speed.


The C/Tr: C refers to the colour of the vehicle Tr refers to the interior colour A/TM is your transmission type. None of those numbers identify the rear end ratio.

What you need to do: Since you have to replace the rear end, yank it out. Examine the ring & pinion gears on the differential carrier. Mark on each a starting point, and count the teeth on both the ring & pinion gears. Now, after you have both totals of teeth, divide the # of teeth on the pinion by the number of teeth on the ring gear. Example: 12 teeth on the pinion, 46 teeth on the ring
12/46 = 3.83 ratio

Aug 22, 2008 | 1993 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...