Question about 1991 Chrysler LeBaron

1 Answer

Transmission for 1991 chrysler lebaron

My transmission shifts out great until it warms up then I think it may shift out to 2nd but no further, I can go about 45miles an hour so whatever gear that is any simple suggestions? I have already changed the filter and fluid. There were shavings on the magnet in the pan. I am a 115lb female keep that in mind when advising me

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,187 Answers

The problem may be connected with the shaving on the pan. It may or may not be related to the issue that you have. You mention that the issue only occurs when the car has warmed up. This may indicate a problem has something to do with the lubricant. Check for leaks underneath by placing news paper underneath the car then check if there is fluid in the morning. There could be an issue with some of the oil seals in the transmission. Double check the fluid levels if it changes or drops from the factory specified levels. The leaks may not necessarily mean that you would see oil dripping from the car but the oil may stay on the outer housing of the transmission. Pay close attention to how many times you are able to shift to identify where the shifting ends. The shifting can be controlled by either a cable or electronically. If it is a cable, then check if it is worn out. For an electrical transmission you should see wiring towards the transmission. Check the condition. An electronically controlled transmission would get signal from a speed sensor for its shifting. Have have velocity sensor checked. This is normally a cheaper fix than having the transmission repaired. Observe also if there is a burnt smell. If there is you may have to have the transmission serviced as the transmission may be giving off to much heat damaging internal parts. The longer that you run the car without having it fixed would cause more damages.

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 chrysler lebaron shift is sliping what could it be


If not low on flouid may need new bands in your transmission. good luck.

Mar 27, 2011 | 1991 Chrysler LeBaron

1 Answer

Not shifting


Need more info, describe the problem, what you were doing when it happened & if there is a history of the problem progressing.

right now I'd say the transmission is bad, but... I need more info

Feb 16, 2011 | 1991 Chrysler LeBaron

1 Answer

I have a 1991 accord lx. Was only functioning in


No, those sensors are seperate from transmission, should be a solenoid that is electrically controlled inside the transmission that controls the shifting.

Apr 05, 2010 | 1991 Honda Accord

1 Answer

92 lebaron wont shift


when you shut off the enging will it shift ? if it does the clutch would be the first thing I would check

Aug 04, 2009 | 1991 Chrysler LeBaron

1 Answer

Cant get my Lebaron too shift into 3rd gear, it will shift into 1st and 2nd but just wont go into 3rd not even if you shut it off and restart it, or unplug the battery and rehuck it up.


Vehicle Speed Sensor or Variable Speed Sensor (located on the transaxle - closest to the drivers side front tire. it has a two pin connector)

Jun 13, 2009 | 1992 Chrysler Lebaron

1 Answer

Transmission automatically shifts to low at idle


after my 2003 chrysler concorde is warm I slow down from the hwy and right before I stop my car shifts to LOW gear and stays there until I turn my car off and start it.

May 05, 2009 | 2003 Chrysler Concorde

1 Answer

91 lebarron wont shift grears when its in drive,


Does it act like it is stuck in 2nd? (Limp in mode) Have the TCM scanned it has trouble codes stored in it.

Apr 14, 2009 | 1991 Chrysler LeBaron

1 Answer

1992 chrysler lebaron


First and foremost, check the fluid! Second, check ALL the vacuum lines in the vehicle. Now as for the fuse... referencing the shop manual, I can not find a transmission related fuse. Did you try checking the trouble codes, if any?

Aug 17, 2008 | 1992 Chrysler Lebaron

1 Answer

Rough shifting


try puting some lucas trany fluid in it and see if it helps

Aug 12, 2008 | 1991 Chrysler LeBaron

3 Answers

The A-604 ultradrive transmission goes into 2nd gear or neutral at ANY speeds


I have a 90 lebaron when i first take off and it shifts good till i hit 3rd it wants to jump until i get about 35 then it will drop ito low even if im going 45 or 55 mph what would cause this.

May 17, 2008 | 1991 Chrysler LeBaron

Not finding what you are looking for?
1991 Chrysler LeBaron Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...