Question about 1994 Chevrolet Camaro

3 Answers

HOW DO I GET TO THE CRANKSHATF SENSOR ON MY '94 CAMARO 3.4? . I'M PRETTY SURE IT NEEDS REPLACING, BUT I CANT FIND IT .hAVE I GOT TO REMOVE THE CRANK PULLEY?

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The crankshaft sensor is located at the begging of the intake.To disconnect it there should be 2 screws to take out then twist and pull.For a 3.4 engine follow the air intake up to the manifold it sits right on top.

Posted on Oct 05, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 811 Answers

Check on side of front of motor, behind or next to crank pulley, will have wires connected to it. one bolt, easy

Posted on Oct 03, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 74 Answers

The best way is to buy one to see what it looks like, it will be easeir to find, it usally on the lower part of the motor

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

94 Camero manual trans shifts but when i give it gas to go the engine jus revs car moves at 3 mph or so in all gears even reverse. Any suggestions.??


The clutch driven plate is slipping on the pressure plate. I am afraid the heat caused by this will have damaged the fly wheel ,clutch and pressure plate all will have to be inspected repaired or replaced. If this has just happened you could check out the free play at the clutch slave cylinder rod to the clutch engagement leaver ,the free play should be around 3 mm.

Nov 26, 2014 | 1994 Chevrolet Camaro

1 Answer

94 camaro has a 350 engine and has no spark


need more info does coil have voltage going to it if not sounds like it could be a bad crank sensor

Mar 27, 2014 | Chevrolet Camaro Cars & Trucks

2 Answers

I have a 94 dodge 1500 i have replaced the crank shaft sensor 3 times why do they keep failing?


Make sure its a quality MOPAR part and check harness connector and wiring are in good shape.

Jan 05, 2014 | Cars & Trucks

1 Answer

Ive got a 94 jeep grand cherokee 4.0 liter i put a 93 4.0 liter and caint get it to fire but it has different distributor


i think you pretty much answered your own question there. Use the '94 distributor in the other engine and make sure that all the sensors are in place, connected and all for a 94. Also check the crank position sensor. If left in place during install, they can get damaged if the flywheel hits it. (hope you matched the flywheels too...if different, it will not run.

Nov 30, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Help my camaro wont crank ive tried everything from fuel pump to crankshaft sensor and coils pcm/icm i think it could be the timing how do u know its that and how do u reset it


You cant reset it. So it cranks but wont start? V8? 6Cyl? You cant just guess and throw parts on it hoping you fix it. Have it towed to a shop and diagnosed.

May 12, 2010 | 1998 Chevrolet Camaro

2 Answers

'94 chevy camaro z28 losing power while driving,


check the mas air flow meter could be starting to go and not yet throwing a code.

Jan 17, 2010 | 1994 Chevrolet Camaro

1 Answer

Horn does not work 1996 camaro fuses ok


I have a 94 z28, check under the hood on the actual horns, make sure the plug has not been dislodged, there is also a relay for the horns try replacing that too, there are 4 screws behind the horn/airbag pad to remove the cover if needed. Hope this helps, Good luck

Nov 20, 2009 | 1996 Chevrolet Camaro

1 Answer

How many o2 sensors does the 94 camaro have.


There is two(2) up top.Left-side of top engine.Right under the windshield level.The other one(1) should be on your right side of the engine,on the top.The other two (2) is in the rear,under the vehicle.One on both sides.

Jun 24, 2009 | 1994 Chevrolet Camaro

Not finding what you are looking for?
1994 Chevrolet Camaro Logo

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...