Question about 1983 Ford Fairmont

1 Answer

Frozen cylinder head bolt

How to undo frozen cylinder head bolt

Posted by on

  • Kimbo too May 11, 2010

    did you try a good wack with a hammer?, get a good solid bit of hardwood and give it a thump, won't matter much if you twist it off, you can always get to it once the heads off.Head to the wreckers for another bolt.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 881 Answers

Depends were its frozen in the block or in the head
but yes get a good solid round bit of either steel or brass and put it on the head bolt and hit it hard a few times and it should start to move ,,,
When it starts to move undo 1/2 turn then 1/2 do it up and keep doing it a bit more each time till it comes a lot easyer when about 3 turns out spray with 10per cent oil and 90 percent petrol mix and waite for 10 minutes and out it comes

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remove heads


Depends on what kind of heads you talk about.

Apr 03, 2016 | 2005 Kia Sedona LX

1 Answer

Parts diagram for clutch slave cylinder nissan D40


It's easy put new master cylinder in place but don't connect rod to clutch pedal or bolt it to bulk head and leave metal solace feed pipe undone , connect fluid feed pipe to cylinder then tilt cylinder so slsve out let faces more down wards then top up fluid pot when fluid runs out slave outlet reconnect slave pipe , bolts master cylinder back in place and connect pedal to it , then undo nipple on slave cylinder let fluid run out freely titghten niplle then pump clutch pedal until it becomes firm job done .
15 minute job .

Nov 07, 2015 | 2007 Nissan Navara 2.5

1 Answer

How to get to the piston


Big job and if you need to ask that question, I would doubt you have the tools and knowhow to accomplish, UNLESS you want a big learning experience with Clymer manual in hand.

If you want to look at the top of the piston for some reason, remove the air filter, plug leads and anything attached to the cylinder head. Undo the rocker cover bolts and remove. Remove the Timing Belt. Undo the cylinder head bolts and lift the head off.

If you need to replace a piston, it is much more work and starts with 'remove the engine'.

Why do you need to 'get to the piston'?

Oct 22, 2015 | Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Want to know the amount of torque pressure do i use when tightening the head bolts, and whats the sequence?


To install:

0996b43f80208f65.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head bolt torque sequence-3.8L engine

  1. Install the new cylinder head gasket with the arrow pointing to the front of the engine.
  2. Install the cylinder head.
  3. Install NEW cylinder head bolts. Torque the bolts in sequence, as follows:
    1. Step 1: 37 ft. lbs. (50 Nm).
    2. Step 2: Plus 120 degree turn.
To install:

0996b43f802316ea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines

  1. Install the cylinder head with a new gasket.
  2. Apply thread sealer to the head bolts.
  3. Tighten the cylinder head bolts to 37 ft. lbs. (50 Nm) plus an additional 90 degree turn.

Dec 16, 2010 | 2002 Pontiac Grand Prix

1 Answer

Whats the bolt pattern for my 1995 ford escort head?


1.8 liter..NOTE: Lubricate the cylinder head bolts using the specified engine oil.

Install the cylinder head bolts. Tighten the cylinder head bolts in 2 or 3 steps in the sequence shown to 76-81 Nm (56-60 lb-ft).

b064be7.gif
1.9 liter
Apply a light coating of engine oil to the threads of the new cylinder head bolts. Install the new cylinder head bolts to the cylinder head. Following the sequence shown below, tighten the cylinder head bolts to 40-60 Nm (30-44 lb-ft). Loosen all cylinder head bolts approximately two turns, then retighten the cylinder head bolts to 60 Nm (44 lb-ft) following the sequence shown. After tightening, turn all bolts 90 degrees, in the same sequence. Complete bolt tightening by turning them an additional 90 degrees, in the same sequence. 398246b.gif

Aug 21, 2010 | 1995 Ford Escort

1 Answer

Cylinder head bolt torque chevrolet 3.4


here is the troque spec for the cylinder heads.

Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees


Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
first pass 44 ftlbs
second pass 95 degrees

Jan 30, 2010 | 2003 Chevrolet Impala

1 Answer

What tool would i need to remove cylinder head bolts on a 93 ford escort gt


Hi
A cylinder head removal tool is provided for removing the cylinder head from the engine block of an engine.The tool comprises an elongated bar made of tool steel with means for bolting the bar to the cylinder head and for mounting pusher bolts which can be tightened down onto exposed threaded ends of frozen studs holding the cylinder head. As the bolts are tightened down onto the studs the cylinder head is gradually lifted upward free from the studs.
Thanks for contacting fixya.com

Nov 05, 2009 | 1993 Ford Escort 4 Door

1 Answer

Head bolt rounded off on magene 2lts edi its 2001


if you can access the bolt with a dremel tool, you can grind new flats in the sides and try a slightly smaller six pointed socket. If you have an arc welder, you can weld another good bolt to the top of the rounded off bolt head and use the head of the good bolt to undo it.

Jan 07, 2009 | 1986 Renault Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...