Question about 1991 Honda CRX

2 Answers

How do you install adjustable lowering coilover springs on a 1991 Honda CRX SI?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

You will want to remove your stock struts and depending on whether it is a partially threaded kit or fully threaded kit, you will need to remove the stock upper strut mounts and replace them on the coilovers. If they are adjustable, I would recommend placing the adjustment perches mid-range which just makes it easier for further adjustment when you get it on the ground. From there they should bolt up the same as stock. Be careful with spring compressors if you are taking the upper strut mounts off of your existing struts!

Posted on Aug 28, 2012

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Honda Expert
  • 268 Answers

NOT NECESSARILY IN ORDER: Remove the 2 nuts from the top of your shock tower under the hood - remove the pivot bolt at the bottom of your shock fork - remove the upper control arm ball joint nut - remove the lower control arm ball joint nut - bang on the thick metal near the ball joints with a hammer (not hitting the rubber or the ball joint's bolts - remove the tie rod ball joint nut and do the same with the hammer - pull the shock and spring assembly out - You might need a spring compressor to take out the stock spring safely - remove the nut on top of the shock - It's recommended that you replace your shocks now - install the new springs according to the directions with the package - get a camber correction kit for your car - put it back together and immediately go pay for an alignment. Good luck.

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the firing order for a 1991 crx si


the firing order for your 91 crx should be 1, 3, 4 and 2. You need to identify where the rotor points to when cylinder 1 is at top dead center.
Cylinder number 1 is the one closest to the accessory belts (alternator, power steering , etc, hope this helps.

Aug 10, 2014 | 1991 Honda CRX

1 Answer

What is the firing order for a 1991 crx si


All Honda 4 cylinder engines that I have worked on have a firing order of 1342. That is the firing order on your CRX. #1 is the cylinder closest to the timing belt.

Aug 10, 2014 | 1991 Honda CRX

1 Answer

Valve lash 91 honda crx si 1.6 sohc


For this engine the valve lash if; Intake .007-.009 and the exhaust valves are .009-.011. Be sure to adjust these when the engine is cold, as a warm exgine will affect the measurements. The locknuts should be torqued to 10 ft/lbs. REMEMBER..."loose is good"..in other words when adjusting the valves DO NOT make them "tight feeling" with the feeler gauge. If you do, you run the very real danger of burning the valves. Honda, I believe, recommends that you should check these every 15k to 24k miles. Happy motoring !

Jun 29, 2010 | 1991 Honda CRX

3 Answers

1991 Honda CRX Blower Motor


most likely it is on the passenger side under the dash

Mar 11, 2010 | 1991 Honda CRX

1 Answer

HOW DO I INSTALL GLOW GUAGES ON MY 1991 HONDA CRX SI


you'll need to take the gauge cluster out and disassemble it. then take off the pointers making sure to note where they're pointing to. then apply the new face. and wire power and ground. put the pointers back on and reassemble.

Feb 12, 2010 | 1991 Honda CRX

1 Answer

1991 honda crx si m/t almost impossible to shift after it warms u


Have you adjusted the clutch cable enough to allow it to disengage the clutch ? try that first. Is this the original clutch?

Jun 11, 2009 | 1990 Honda CRX

1 Answer

1991 CRX rear disc conversion


you would have to check the axle is the same

Feb 18, 2009 | 1991 Honda CRX

2 Answers

Idles good but,above 1300 rpm serges evenly at about 3800 no more serge 1990 crx 16 valve 1.6 very strong serge


Have you replaced the fuel filter? if not, it could very well be the problem

Oct 14, 2008 | 1991 Honda CRX

Not finding what you are looking for?
1991 Honda CRX Logo

735 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...