Question about 1994 Jeep Wrangler

1 Answer

1994 jeep wrangler 4 banger. Have replaced seal to oil pan. Still leaks on the pass side. What else can i do befor I break it down again?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

Make sure to clean the surface real well, and at the corners of the pan where the crank journals are located you will need to dab some rtv in the crevices on each side of the bearing caps

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Jeep engine problems


Check for intake leaks, intake hose leaks, check mass air flow sensor.
02 sensors will keep setting off a lean code until the air problem is fixed.

Jul 20, 2014 | 1997 Jeep Wrangler

2 Answers

Oil Is Leaking Out Under The Harminc Balancer On my 92 Jeep Wrangler,4.0 6cyl. I Replaced The Main Seal & Put A New Balancer On & It Still Leaks From The Bottom Of The Balancer


  1. timing cover is leaking oil betwwen cover and block
  2. Disconnect the negative battery cable.
  3. Remove the drive belt(s), fan and fan shroud. If equipped, remove the accessory drive belt pulley.
  4. Remove the vibration damper retaining bolt and washer. Remove the vibration damper using a suitable puller.
  5. Remove the accessory drive brackets attached to the timing cover.
  6. Remove the A/C compressor, if equipped, and alternator bracket from the cylinder head and move to one side.
  7. Remove the oil pan-to-timing case cover bolts and the cover-to-cylinder block bolts.
  8. Remove the timing case cover front seal and gasket from the engine.
  9. Cut off the oil pan side gasket end tabs and oil pan front seal tabs flush with the front face of the cylinder block. Remove the gasket tabs.
  10. Clean the timing case cover, oil pan and cylinder block gasket surfaces.
  11. Remove the crankshaft seal oil seal from the cover by prying it out with a suitable tool.

To install:

  1. Install a new seal in the timing cover using a suitable seal installation tool.
  2. Apply sealer to both sides of the replacement cover gasket and position the gasket on the cylinder block. Cut the end tabs off the replacement oil pan gasket corresponding to those cut off the original gasket. Attach the end tabs to the oil pan with sealer.
  3. Coat the front cover seal end tab recesses generously with sealer and position the seal on the timing cover.
  4. Apply engine oil to the seal-oil pan contact surface, then position the cover on the cylinder block.
  5. Insert timing case cover alignment tool J22248 or equivalent, in the crankshaft opening. Install the cover-to-cylinder block bolts and tighten them to 62 inch lbs. (7 Nm). Install and tighten the oil pan-to-cover bolts to 11 ft. lbs. (13 Nm).
  6. Remove the cover alignment tool and position a replacement oil seal on the tool with the seal lip facing outward. Apply a light coat of sealer to the seal and a light coat of oil to the crankshaft. Install the seal on the timing cover.
  7. Apply a light film of oil to the vibration damper hub seal contact surface. Install the vibration damper using a suitable installation tool.

Do not hammer the damper into place as damage may result to the damper or engine.

  1. Install and tighten the crankshaft vibration damper bolt to 80 ft. lbs. (108 Nm).
  2. If equipped, install the crankshaft pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  3. Install the accessory brackets.
  4. Install the fan and fan shroud.
  5. Install the drive belt(s) and adjust to the proper tension.
  6. Connect the negative battery cable.
  7. Start the engine and check for leaks
  8. .

Jan 18, 2011 | 1992 Jeep Wrangler

1 Answer

I have an oil leak and was just lookin around under neath and found a seal that is square and has been torn and no longer seals it is just behind the oil pan what is that seal


If it is an automatic, and by your description, Behind oil pan, you mean toward the back of the vehicle, and the fluid is red,sounds like your Transmission Pan Gasket. They are flat and sometimes they squish out the side of the gasket area. Easy to replace that and filter, BUT very Messy as the pan will hold 3~4 quarts of oil and You will spill it everywhere If you are not ready for it. A trans shop can offer Filter flush and fluid for about $79.. in about an hour. Good luck, Bill

Aug 05, 2010 | 1987 Jeep Wrangler

3 Answers

My 2000 jeep wrangler sport is leaking fluid just under my front differential. whats wrong?


change the front pinion seal and check the axle seals for leakeage

Jan 13, 2010 | 2003 Jeep Wrangler

1 Answer

2002 Jeep Wrangler appears the rear of the oil pan gasket is leaking. How hard is it to change out and any tips/ 2001 jeep wrangler something leaking inside back wheel is it the rear seal


not hard to change out that oil pan gasket tip- just think of it as a simple job nothing can go wrong you can do this i promis-----its not the rear seal its the shocks and struts common tell tell signs-get new ones before its tooo late

Apr 05, 2009 | 2001 Jeep Wrangler

1 Answer

How do i change a oil pan geskrt in a 94 jeep wrangler/


On most, you need to remove all bolts around the perimeter of the pan, (You may want to remove starter to get to fasteners there) then slide a paint scraper between the pan and block to break the seal. Generally there is enough room to get the pan out. If you need a bit more room, support the transmission with a jack (use a piece of plywood on top to avoid bending anything) remove both engine mount through bolts and raise engine slightly (not too much or you will break something)

Mar 21, 2009 | 1994 Jeep Wrangler

1 Answer

Fill the oil level on a 1994 Jeep Grand Cherokee,


yes you should remove the access. This will cause the engine to drown in a sense and have to fight. It is always safe to put in not enough to too much. You onlt have a certain amount of oil that can be placed in the pan before it runs up into your cylinder heads and can break the seal on the gasket. Then you would have to pay to get the cylinder head gasket replaced.

Feb 23, 2009 | 1994 Jeep Grand Cherokee

2 Answers

Jeep Wrangler oil pan leak


You need to Put Blue ATV Silicone on Both sides of the Gasket to get it to Seal Properly. This is a High Temp Sealant and Once Set it will fix the Problem.

Jan 26, 2009 | 1997 Jeep Wrangler

1 Answer

2002 Jeep Wrangler appears the rear of the oil pan gasket is leaking. How hard is it to change out and any tips/


It is the oil pan gasket all you have to do is drop the oil pan clean the bottom of the engine block and the surface of the oil pan and install the oil pan again. a very simple process. Make sure that it is not the rear main crank seal that is leaking. If it is the rear main then you will have to remove the tranny to replace the rear main seal.

Jul 27, 2008 | Jeep Wrangler Cars & Trucks

Not finding what you are looking for?
1994 Jeep Wrangler Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...