Question about 2005 Pontiac Grand Prix

1 Answer

Programmed key will not open 2005 Pontiac GP door

Had a replacement key programmed at GM dealership. It will start the car but won't open the locked door. When the key goes in the door lock it will turn and you can hear a buzz sound like it is unlocking but it won't unlock the door.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Does the old key open the door? if so, the new key is cut wrong. if not, theres a problem with the lock.

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car with lock light on dash


GM factory security sytem light, flashes when you lock or unlock the doors. If a key is inserted into the ignition, and that key is not programmed into the computer, the computer shuts the engine down and car will not crank, and if I remember correcty, when that happens you have to have the car towed into the GM dealership, and they have to hook your car up to GMs tech three diagnostic system.

Feb 26, 2014 | 2006 Pontiac G6

1 Answer

Programming 2006 pontiac pursuit fob


Gm and Chevy fob can be programmed at home. I have done it my self for a 01 chevy a 03 sunfire.
The steps on
 Step 1 of 5
Get in your Pontiac G6 and make sure all the doors and the trunk are closed.

 Step 2 of 5
Put your key in the ignition and hold the "Lock" button on the driver's car door.

 Step 3 of 5
Turn the G6 key in your ignition from "On" to "Off" while holding the "Lock" button, and do two more cycles of "On" and "Off" in quick succession.

 Step 4 of 5
Release the "Lock" switch on your door and press and hold the "Lock" button on your keyless remote for 10 to 15 seconds.

 Step 5 of 5
Remove the key from the ignition of your G6, and test the programming.

Or

Or

 Step 1 of 9
Enter your vehicle and close all of the doors behind you besides the driver's door. Be sure to have your keyless remote and ignition key in hand.

 Step 2 of 9
Insert and remove the key from the ignition twice in a row and then close and open the door twice in a row.

 Step 3 of 9
Insert and remove the key from the ignition again and close and open the driver's door two more times.

 Step 4 of 9
Insert the key into the ignition and close the driver's door.

 Step 5 of 9
Cycle the key in the ignition "On" and then "Off" and then remove the key from the ignition.

 Step 6 of 9
Wait for the locks to cycle to indicate the beginning of the programming sequence.

 Step 7 of 9
Press and hold the unlock and lock buttons on your remote for two seconds and then release.

 Step 8 of 9
Press and hold just the
lock button on the remote for three seconds and wait for the locks to cycle to indicate successful programming.

 Step 9 of 9
Repeat steps seven and eight to program any additional remotes and open the driver's door to end the programming sequence once you are finished.
Hope this helps

Feb 04, 2012 | Cars & Trucks

1 Answer

How do i program a keyless entry remote on an 05 pontiac montana


Hello, this can only be done with a GM tech 2 scan tool.


  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool.
  4. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  5. Repeat the previous step in order to program up to 4 transmitters.
  6. Remove the scan tool.
  7. Operate the transmitter functions in order to verify correct system operation.

Nov 07, 2010 | 2005 Pontiac Montana SV6

2 Answers

2003 remote control for 2005 van?


Transmitter Programming
If you lose a transmitter, program the old and new transmitter(s) into the remote control door lock receiver's memory. Up to 4 transmitters may be programmed.


Important
Once the remote control door lock receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information, requiring the programming of all transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If more than 1 receiver is being programmed at the same time, it is possible that the same transmitter could be programmed to more than 1 remote control door lock receiver.


Perform the following steps in order to program the transmitter:

Remove the ignition key from the ignition lock cylinder.
Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.
Close all of the doors.
Close the liftgate.
Turn the ignition lock cylinder to ACC.
Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
Open and close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.

Important
After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat the previous step on each additional transmitter to be programmed.
Remove the ignition key from the ignition lock cylinder.
Install the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Wiring Systems. IF THIS WAS HELPFUL,PLEASE RATE,THANK YOU

Jul 15, 2010 | 2005 Pontiac Montana

1 Answer

I have a problem with opening car doors with remote for 1997 pontiac sunfire. I noticed that when you are in the car and you activate the open and close switch from drivers side the locks at the rear open...


Try this procedure...

KEY FOB PROGRAMMING INSTRUCTIONS
Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old & the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If u program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver is seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle is doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body & Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open & then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If u do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press & hold the transmitter LOCK & UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body & Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Hope this help (remember comment and rated this).

Apr 16, 2010 | 1997 Pontiac Sunfire

1 Answer

Remote start function on remote doesn't work for a 2005 Pontiac G6.


Replace battery first and see if that help, if not then follow steps below, if you cant figure it out or it still doesn't work, or take it to the dealer, it could be remote module is faulty. Keep the windows open as a safety measure, then,

Remove the ignition key from the ignition lock cylinder.

Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.

Close all of the doors.

Close the liftgate.

Turn the ignition lock cylinder to ACC.

Turn the ignition lock cylinder to OFF, & then back to ACC within 1 second.

Open & close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.

Important
After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.


Press & hold the transmitter LOCK & UNLOCK buttons simultaneously for 14 seconds.

Repeat the previous step on each additional transmitter to be programmed.

Remove the ignition key from the ignition lock cylinder.

Install the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Wiring Systems.

Oct 07, 2009 | 2005 Pontiac G6

2 Answers

Replacement valet key


you HAVE to get it from a nissan dealer.the valet key has a tooth cut that is different,so that is does open the trunk or glovebox and there is a lockout switch in the glovebox.
but there is a chip in the key and the car will not start without it.
if you try to start the car a few times without the chip,the car will have to be towed to get the body control module re programmed .

May 28, 2009 | 2005 Nissan Altima

2 Answers

1999 pontiac montana keyless entry


If this is a Factory installed System You will have to get it from the Dealer. If not, You need to find out Who the Manufacturer is of the System and Contact them for a Replacement.

Jan 09, 2009 | 1999 Pontiac Montana

1 Answer

Key Fob Programming


key fobs have to be the same gm id number on back of fob and need to be programmed for your car by the dealer. its expensive . i had to have it done on my car. other fob i had could not be programmed to work, wrong gm id number

Nov 25, 2008 | 2005 Pontiac G6

Not finding what you are looking for?
2005 Pontiac Grand Prix Logo

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...