Question about 1997 Dodge Intrepid

1 Answer

I can't get the right drive axle to come off of my 1997 dodge intrepid. do I need any special tool?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

It will come out with a pry bar.some are really hard.there is a small c-ring on the end that has to squeeze in.

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove and replace a transmission on a 2001 Intrepid Dodge?


They pop out. Pry bar does it. Start with a screwdriver if needed. Doing it on the ground is a pain. You may want to remove the axle bracket. And the axle from the wheel bearing.

Dec 31, 2016 | Dodge Intrepid Cars & Trucks

1 Answer

I was driving when my 1997 dodge intrepid 3.5 shut off and wouldn't restart and still won't restart , i looked it over and determine i wasn't getting no spark so i changed the plugs , plu


It could be the computer. It could be a relay or something in the wiring harness too.
You would need a shop manual to get the wiring diagrams and test procedures to find the problem.
You need to know if the coil assembly and injectors are getting power from the ASD relay, and if the computer is getting signals from the cam and crank sensors.

Jan 23, 2013 | 1997 Dodge Intrepid

1 Answer

Mi 1997 dodge intrepid jerks at 65 to 70 milles ,what can that be?


Hello
The engine and transmission in this cars drivetrain are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s)

Jul 04, 2012 | 1997 Dodge Intrepid

1 Answer

Removing right cv axel


The axle is held into the transmission by an internal round "circlip" snapring, to release this the first time is difficult. What you must do is pull straight out on the axle in a fast snapping motion, however you create this snapping motion is up to you and what you have on had to put over the axle shaft, it most be very fast and very hard and straight out motion, if not it will not release from the tranmssion.

Jan 23, 2012 | 1997 Dodge Intrepid

1 Answer

Axcle shaft 2003 dodge intrepid


remove tire/wheel and remove axle nut!! i thinks its a 32 mm socket and then take the upper strut bolts out of the knuckle theres 2 bolts 18mm if not there 15 mm bolt heads and tilt the knuckle outwards then drive the axle back with a hammer til it clears then take a flat tip bar and pry the axle out of the tranny

Jan 21, 2010 | 2003 Dodge Intrepid

1 Answer

Do i need any special tools too replace the gears


it does require some special equipment. most likely have the 9.25 axle in the truck which has adjusters on both sides of the differential that are threaded in the housing. these require a special tool to adjust and set proper backlash. also helpful to have a press with bearing pullers/installers. need a dail indicator to set backlash also

Nov 15, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Yes i have a 1997 dodge intrepid 3.5L and the right side axle is poping how can i fix it


replace the c v joint you can buy one at your local auto parts store

Sep 25, 2009 | 1997 Dodge Intrepid

3 Answers

1997 Dodge Intrepid 3.5L How to replace water pump and timing belt.


This a dificult and time consuming project. Suggest you purchase you a repair manual which gives you diagrams and detailed instructions for this type of repair. Difficult to explain procudure in writing.

Sep 10, 2009 | 1997 Dodge Intrepid

1 Answer

Lower radiator hose romoval on 1997 Dodge Intrepid


if it is the "pinch" style clamp you will need a pair of hose clamp pliers that are made for that type of clamp. they make some that use bicycle brake cables for better reach. you can get it at a auto parts store like pep boys or kragen. those clamps are a pain in the a$$ but with the right tools you can get to it without removing any components

May 05, 2009 | 1997 Dodge Intrepid

1 Answer

Changing fuel filter


its easier and less trouble some if you have the right tools but it can be done with a screw driver and a pair of Needle nose pliers. Use fineness.

Feb 09, 2009 | 1995 Dodge Intrepid

Not finding what you are looking for?
1997 Dodge Intrepid Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...