Question about 1988 Suzuki Samurai

1 Answer

Steering knuckle for 1988 suzuki samurai need diagram to show me step by step and want to change front barrinngs inner and outter.this is a jeep and sounds like a front wheel drive car with bad back axelsand when turning makes noise.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 102 Answers

No noise should come from the front when you are driving on asphalt as you are in 2WD, right? If you have been using 4WD with the hubs locked on asphalt, then there's every chance that your CVs are shot. You are, of course, unlocking the hubs when you are only in 2WD aren't you? When the hubs are unlocked and the car is in 2WD, the CVs do absolutely nothing. With the hubs unlocked, and the front jacked up, spin the wheel and listen for noises, and grab the top and bottom of the wheel and wiggle it in and out and check for movement. If there's no noise and very little movement, then your bearings are unlikely to be the problem. These are taper roller bearings and can be adjusted.

Posted on Oct 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have brought a second hand lockset for my suzuki sj samurai (Ignition lock, both door locks and the tailgate lock and matching key) and i need to replace all of them as i have lost my key and cant get a...


The fastest thing to do is to take one of the locks to a locksmith and have them make a key from it.This will save a lot of time and disassembly.If you still want to change all the locks,you will have to figure out how to remove the door trim panels,disassemble the steering colum,etc.(every vehicle is a little different,never worked on a Samurai myself)

Sep 06, 2012 | 1991 Suzuki Samurai

1 Answer

What causes violent front wheel shake in a Suzuki samurai


i had a simular problem with my samuria i changed the tie rod and steering stabilizer and it does not shake anymore

Oct 09, 2011 | 1988 Suzuki Samurai

1 Answer

I have a 1990 gmc truck not 4x4 it is a 2 wheel drive. when i turn left the steering will lock up and i can't get it to turn right. i have put on new inner and outter tie rod's. and a new idler arm. what...


with the front wheels of the ground remove the outer tie rods from the knuckles. Turn the knuckles by hand. Do they move freely? if not than the upper or lower ball joint are binding.

With the tie rod end still disconnected turn the steering wheel to the left. Does it still bind up? If so you probably have a bad steering gear box.

Oct 16, 2010 | 1990 GMC C1500

2 Answers

Hard to steer


HARD STEERING PROBLEM. POSSIBLE CAUSE LACK OF LUBRICATION AT BALLJOINTS AND THE TIE ROD ENDS,FRONT WHEEL NEED ALIGNMENT,CHECK FOR LOW TIRE PRESSURE.

Aug 15, 2010 | 1988 Suzuki Samurai

2 Answers

Power steering "pop"


On these vehicles, rack & pinion mount bushings and inner tie rod bushings basically wear away to a point sometimes they fall apart completely, dangerous to drive if thats the case. Easy fix for a trained technician.

Feb 24, 2010 | 1994 Chrysler LHS

1 Answer

Need help replacing front hub


Here's the steps....getting some pics for you....hang on a minute or two.

Front Hub Removal & Installation To Remove:
  1. Remove steering knuckle.
  2. Using a suitable slap hammer, remove wheel hub assembly.
  3. Using a suitable bearing press, remove outer bearing, oil seal, outer bearing race and preload spacer.
  4. Remove inner oil seal, inner wheel bearing and inner bearing race.
NOTE: It is not necessary to remove dust cover (back plate).
To Install:
  1. Using a suitable bearing press, install bearing races in steering knuckle.
  2. Pack the bearings and hub area with lithium grease.
  3. Install inner bearing in steering knuckle.
  4. Lubricate lip of NEW inner seal and press seal into knuckle.
  5. Install preload spacer into bore.
  6. Install outer bearing into bore.
  7. Lubricate lip of NEW outer seal and press seal into knuckle.
  8. Using an appropriate tool, support inner wheel bearing and press wheel hub into knuckle with a force of 2500kg.
  9. Install NEW inner seal.
  10. Install knuckle assembly.

May 13, 2009 | 2004 Kia Rio

2 Answers

Steering on 92 suzuki samurai


hi check that the power steering system has not got a leak and drained the fluid if not check the filler bottle see if theres any fliud if there is then check the power steering belt is tight enough to turn the pump if this is the case you are going to need to change the power steering pump yates210456

Sep 02, 2008 | 1988 Suzuki Samurai

1 Answer

Front axle how to remove half shaft


Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Aug 18, 2008 | 1999 Suzuki Vitara

1 Answer

Suzuki Samurai 4x4 Jeep Front Wheel Bearings


hi have a look here
Suzuki Workshop Manuals

please rate my answer if useful

Oct 31, 2017 | 2005 Suzuki Samurai

Not finding what you are looking for?
Cars & Trucks Logo

642 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...