Question about 1998 Acura SLX
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
A) Remove the screws in the following locations:
When I examined the problem that I had with my Odyssey, I found the following:
Posted on Nov 27, 2008
You have totake the door panel off to get to the wiring harness. door panel should be held by plastic clips so all you have to do is grab a corner and give a nice tug. First check to make sure there are no screws in it that I may have missed. Remove the clips from the door with a fork and put them in the panel and replace the panel by using a small tap.
Posted on Jan 08, 2009
SOURCE: window off track
Looking at the opened door from the inside remove the philips screw near the upper hinge. Pry the speaker grill off with a thin blade putty knife, starting at the bottom left and work to the right. Remove speaker screws and the three screws in the recessed plastic spaces behind. Remove the square covers behind the handle and in the arm rest. Remove the 2 philips screws exposed. Start to pry from the top hinge side between the plastic door panel and the metal door. Work your way around the door until plastic clips release. Once the bottom of the panel and sides are free, lift the panel up and off the door being careful not to pull wiring and door handle mechanism loose. Unplug the as much of the wiring as you can and support the panel so as to not stretch the wiring. Pop the plastic retaining clip on the door handle connecting rod and lift the rod out of the handle. Slowly peel back the vinyl/rubber door cover stuck to the metal door. The window is held in the lower track with two clips that are bolted to the track. Unbolt by raising or lowering the window and using a 10MM socket on the nuts to loosen. Remove the window seal along trhe bottom of the window opening by prying straight up. You can then remove the window and re-epoxy in the lower clips and reassemble window in reverse order.
Posted on Mar 24, 2009
On vehicles without power windows, place a soft cloth under the window regulator handle and pull upwards on the cloth to release the snapring. Remove the regulator handle and plate.
Fig. 2: Using a taped prytool, carefully remove the bezel portion of the handle
Fig. 3: Remove the bezel by pulling towards the tip of the handle
Fig. 4: Remove any screw covers . . .
Posted on Mar 31, 2009
SOURCE: driver side window off track
2 sets (total 4) T30 Torx screws need to be removed.
The 2 holding the interior door handle grip / cup.
And then behind where the cup is, there are 2 more, that secure the door panel to the door.
FWIW, there are also 2 philips screws. One at the top, near the mirror. The second at the moveable door handle latch.
Lastly, of course, the standard "pop" sort of fasteners, around the perimeter on the 2 sides and bottom of the door panel. Also, there are 2 light blue plastic alignment posts (that do *not* fasten).
When re-assembling, make *sure* to properly catch / engage the door panel's top black plastic lip into the 3 hidden metal "U" holders, at the very top of the door panel.
Posted on Jul 26, 2009
Tips for a great answer:
Jul 29, 2016 | 2003 Honda CR-V
Sep 14, 2014 | 2003 Nissan Altima
Dec 31, 2010 | 1996 Acura SLX
Jul 07, 2010 | Honda Odyssey Cars & Trucks
Apr 01, 2010 | 2003 Mazda MPV
Jan 15, 2010 | 1996 Pontiac Grand Am
Oct 13, 2009 | 1993 Acura Integra Hatchback
Mar 30, 2009 | 1992 Acura Legend
Jan 08, 2009 | 2001 Acura Integra
87 people viewed this question
Usually answered in minutes!