Question about 1990 Nissan Stanza
I have a 1990 Nissan Stanza with a 2.4 engine front wheel drive. The problem is with the transmission. On the side facing the radiator towards the back on top of the side is a round something like 3" cover or seal or something that is gushing fluid from around this part. Does anybody know what this is and how to fix or replace this part? Thanks
THAT sounds like the foward pump housing cover and the only thing to do is to take it to the auto trans people as it has to be remover and replaced from inside
I could be wrong but i dont think so
LET ME KNOW HOW YOU GO Ron
Posted on Oct 03, 2009
Testimonial: "I think your right about what that cover or plate is. But I need to do the work myself can a do it your selfer not handle this job?"
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Oct 27, 2016 | Nissan Cars & Trucks
Aug 31, 2012 | 1990 Nissan Stanza
Sep 07, 2011 | 1990 Nissan Stanza
Jan 20, 2011 | 1988 Nissan Stanza
NISSAN STANZA WAGON - Manual Transmission
Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?
Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.
1. Cold vehicle.
Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).
Remove top starter motor bolt 14 mm with universal & long extensions.
Raise vehicle on hoist.
Remove front splash pans 10 mm.
Automatic transmission: Drain 2 qts out.
Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.
Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).
Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).
Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).
Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).
Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.
CAUTION: Transaxle side seals are cut by spline teeth.
Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.
Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.
Remove nut that attaches crossmember to engine mount.
Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.
Remove following brackets to allow starter assembly to pass through bottom:
tubular support bracket - engine to transaxle
angled support bracket - driveshaft bracket to engine mount
manifold collector stay - (bottom bolts)
Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.
NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.
Remove bottom starter motor mounting bolt.
Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.
When installing starter, connect cable, install/torque starter bolts.
Nov 03, 2010 | 1986 Nissan Stanza
May 27, 2010 | 1990 Nissan Maxima
Apr 14, 2010 | 1991 Nissan Stanza
Apr 03, 2010 | 1991 Nissan Stanza
Jan 25, 2009 | 1999 Subaru Legacy
Nov 20, 2008 | 1992 Nissan Stanza
178 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: