Question about Chevrolet Camaro

1 Answer

I have a lunarti cam with the following stamped at the end either PIKD108,or P1KD108 are unable to find the specs for it.It came off a small block 400,off my 1970 camaro.Would appreciate any help you can give cheers Maria.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

Nothing under that number comes up on their web site. You should give them a call on thier tech line 662-892-1500. They are open Mon. thru Fri. 7 AM to 6 PM CST. Hope you get the information you are looking for.

Posted on Oct 02, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


It is not a serial number it is the casting number for the block they started producing in 1996 and still going
it being a two bolt it was mostly used in trucks
To find the partial vin and assembly stamp and decoding look at the following site

Feb 06, 2017 | Cars & Trucks

1 Answer

Stamped number on front of engine what is it?

If it is an early model small block that is the EIN # which stands for ENGINE IDENTIFICATION NUMBER. I can tell you everything about the engine with that number. Including where it was built , specs and other goodies.

Nov 19, 2015 | Chevrolet Cars & Trucks

1 Answer

I have 351 cleveland pulled the cam 930554 stamped on it whats the specs

Sep 30, 2014 | Cars & Trucks

1 Answer

I have a 86 302 with a roller cam but I need the specs on it all that is stamped on it is a F5. Any clues

Call the cam manufacturer

You can use your degree wheel & dial
indicator, to measure the lift & duration

Sep 30, 2014 | Cars & Trucks

1 Answer

Camshaft specs

There is no info on a site like this

This is a free chat room


Aug 11, 2014 | Cars & Trucks

1 Answer

What are the camshaft specs? Can anyone help me please?

contact a cam shaft shop that does grinds or a speed shop that sells cam shafts and recite the numbers and they should be able to tell you what cam it is . If the cam has a makers name that will be a big help as well

May 26, 2014 | 1989 Ford Mustang

1 Answer

Daewoo lanos 1.5l timing belt marks


If this is a single overhead cam, possibly A15SMS (engine type):

If you have everything stripped down and can see the crank shaft gear, you will notice an arrow stamped into one of the gear teeth.
this arrow must point towards the bottom, you will notice a mark (notch) cut into the housing, line the arrow on the gear with this notch.

remove the four 10mm bolts that secure the top cover of the timing belt, gently open the cover (not removing it) to see the Cam Gear. You will not be able to remove the cover because of the design.

The Cam Gear should have a line stamped into one of its teeth, this should be pointing up and towards the top. On the inner cover you will notice a notch in the casing, line both up together if it is not already.

You can check the following if unsure:
Remove # 1 spark plug (nearest the Cam Belt) and place a long screwdriver in the hole carefully to feel the piston is at the top, #2 and 3 will be down and the last one #4 at the distributor end will also be up.

Remove the rocker cover and you should see the Cam loabes on #1 piston free, (no pressure on the cam shaft) meaning the valves are closed.


Dec 06, 2010 | 2001 Daewoo Lanos

2 Answers

Im changing the timing belt on my 2000 kia sportage what are the measurments where do i line up the belt and camm

their is timing marks where they suppose to line up stamped into the engine block cam gears and on the head. twin cams u points marks on cam gears straight toward mark on other cam gear

May 30, 2010 | 2000 Kia Sportage

1 Answer

I need the timing marks

you will find on the crankshaft and cam gear a small white arrow. just above the crankshaft will be another arrow stamped on engine block. and just above the cam gear you will see another arrow stamped on the head. both marks will be faceing you when you look at the front of the gears.

Apr 19, 2010 | Dodge Neon Cars & Trucks

1 Answer

Timing belt

Well basicaly there is no adjustment it has timing marks and the belt goes on with the marks on the pulley has a stamped mark up with line marks that go evenly one on each side has to be even with top of the head.crank pulley the woodruff key goes straight up facing the cam pulley.The balance pulley has a v mark on the pulley and a mark on the block and those go together, dont worry about the water pump there is not timing mark on that.Good Luck

May 23, 2009 | 1994 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides