Question about 2004 Ford Taurus

1 Answer

How do i bleed the brakes on a 2005 taurus - 2004 Ford Taurus

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 881 Answers

2 Ways 1 pressure bleed ,,thats with a pressure pump full of brake fluid and undo bleeding nipples one at a time OR the other way 1 person in car 1person filling tank with b/fluid while you get under car a open bleeding nipples 1 at a time starting at the L/H/F then when only fluid cones out lock it up and to R/H/F and then to rear ,,but when open pedal down ,put your finger over nipple so no air goes when pedal is let up and so on..

Posted on Oct 03, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Iv got a '96 ford taurus gl. When bleeding the brakes is there a certain order they should be done in?

Passenger rear, driver rear, passenger front, driver front, hope this helps

May 07, 2016 | Ford Cars & Trucks

1 Answer

How to bleed brakes

Dec 18, 2014 | 2005 Dodge Durango

1 Answer

2002 ford taurus changed master an front an rear brakes did the bench bleed on the master an bleed the lines 3 time still songy pedal please help

You must bleed the antilock brake unit, that takes a special tool, so off to the brake shop or local Ford dealer.

Jan 10, 2014 | Ford Cars & Trucks

1 Answer

Bleed brakes for 2005 prius

release? explain what that means.
what parts were disconnected? MC, tell what you did.
brakes good, bleed, no bad
brakes bad, parts pulled, now bad bleed,???? just a
if you open a fitting north of the ABS main unit, you will be in trouble.

did you read the FSM on PRIUS< if not why not>?
got ABS,? sure...
some cars with ABS, have very specail rules and steps for
bleeding ABS. , including factory scan tools that must modulate
the ABS solenoids to clear air !
i bounce in and read now for you.
it says.
Bleeding the brakes requires the use of the Toyota Hand-Held tester, or other appropriate scan tool. Follow the operating procedures of the Toyota Hand-Held tester, or other appropriate scan tool when bleeding the hydraulic brake system.

Before fiddling any car with ABS, google your car
see what others did wrong.... save lots of grief.
and a tow to a shop.

Dec 22, 2013 | 2005 Toyota Prius

1 Answer

I replaced my brake pads & rotors but now i have no brakes

Assuming you put everything together correctly, you may have let air in the system. Follow the brake bleeding procedure for your car. Becareful with ABS systems the fluid can be under very high pressure. Get pro help if you don't know how.

Sep 14, 2010 | 2005 Ford Taurus

1 Answer

Air in the brake line ,bleed brakes ,replace pads

Please Check Fluid flow Divider Valve & Servo Unit.

Dec 22, 2009 | 1999 Ford Taurus

2 Answers

1999 Ford Taurus, replaced leaking master cylinder, installed new brake pads, bled brake lines, pedal still soft. What else can I check?

There is a special tool required to bleed the brakes, it plugs into the ABS hydraulic control under the hood and holds the ABS valves open to remove the trapped air during bleeding, u will need to have the dealer bleed the brakes, they are most likely the only ones that will have this special too, but u can try an outside shop, I am sure Snap on tools makes this tool in the aftermarket tool catagory..

Dec 18, 2009 | 1999 Ford Taurus

1 Answer

How do u get the spring from the back brake on a 1997 for taurus back on after u have drained the brake fluid??

WHAT the hell are you talking about as you dont do any thing like taking off springs to bleed brakes as the bleeder is on the back of the cylinder and bleeding takes 2 minutes only

Ask for info befor you start playing it will save you days of work

Sep 23, 2009 | 1997 Ford Taurus

1 Answer

When i began to break it feels like I am not going to stop. It shakes so bad it thrusts you all over. I have had 4 wheel alignment, new tires, replaced ball joints and the breaks.

replace front rotors and pads with new napa parts only that should fix the brake issue and make sure you bleed the brakes.

Aug 09, 2009 | 2005 Ford Taurus

Not finding what you are looking for?
2004 Ford Taurus Logo

577 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides