Question about 2004 Chrysler Concorde

1 Answer

How to replace high-mount stop lights - 2004 Chrysler Concorde

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 2,984 Answers

To Remove:

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect the battery negative cable.
  3. Release trunk latch and open trunk
  4. Remove the following:
    • Lamp socket from the CHMSL housing.
    • Bulb from the socket.
To Install:
  1. Install the following:
    • Bulb into the socket.
    • Socket into CHMSL housing.
    • Battery negative cable
NOTE: after completion verify lamp operation


How to replace high-mount stop lights - 5bac824.gif

Posted on Oct 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chevy impala brake light isses switch has been replaced and so have fuses and bulbs still no lights


Do you know how to test using a DVOM - digital volt ohm meter ? Is there B+ voltage going into the brake light switch ? An coming out when the brake pedal is pressed ? What fuse's ? There is only one fuse for the brake lights !
The BRAKE SW fuse in the RH I/P fuse block supplies battery positive voltage to the normally-open stop lamp switch. When you press the brake pedal the switch contacts close and battery positive voltage is supplied to the left and right stop lamp assemblies and to the center high mounted stop lamp (CHMSL). The left and right stop lamp along with the CHMSL are grounded at G302.
Do you know about the right insturment panel fuse box ?
Stop Lamps Inoperative
Step
Action
Yes
No
Schematic Reference: Exterior Lights Schematics
1
Did you perform the Lighting System Diagnostic System Check?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Lighting Systems
2
Press the brake pedal.
Do all of the stop lamps illuminate?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Are all the stop lamps inoperative?
YES - Go to Step 4
NO - Go to Step 7
4
Inspect the BRK SW fuse.
Is the fuse open?
YES - Go to Step 14
NO - Go to Step 5
5
Disconnect the stop lamp switch.
Using a test lamp connected to ground, probe the battery supply voltage circuit of the stop lamp switch connector.
Does the test lamp illuminate?
YES - Go to Step 6
NO - Go to Step 13
6
Install a fused jumper between the battery supply voltage circuit and the stop lamp switch signal circuit of the stop lamp switch connector.
Do the stop lamps illuminate?
YES - Go to Step 12
NO - Go to Step 17
7
Determine if the center high mounted stop lamp is inoperative or the stop/turn lamps are inoperative.
Are the stop/turn lamps inoperative?
YES - Go to Step 8
NO - Go to Step 9
8
Do the turn lamps operate normally?
YES - Go to Step 17
NO - Go to Turn Signal Lamps and/or Indicators Inoperative
9
Disconnect the center high mounted stop lamp.
Using a test lamp connected to ground, probe the stop lamp switch signal circuit of the center high mounted stop lamp at the harness connector.
Press the brake pedal.
Does the test lamp illuminate?
YES - Go to Step 10
NO - Go to Step 15
10
Using a test lamp, probe between the stop lamp switch signal circuit and the ground circuit of the center high mounted stop lamp with a test lamp.
Press the brake pedal.
Does the test lamp illuminate?
Go to Step 11
Go to Step 16
11
Inspect for poor connections at the harness connector of the center high mounted stop lamp. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 20
Go to Step 19
12
Inspect for poor connections at the harness connector of the stop lamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 20
Go to Step 18
13
Repair a open or high resistance in the battery supply voltage circuit of the stop lamp switch. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
14
Repair a short to ground in one of the following circuits:
• The battery supply voltage circuit of the stop lamp switch
• The stop lamp switch signal circuit of the stop lamp switch
Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
15
Repair a open or high resistance in the stop lamp switch signal circuit of the center high mounted stop lamp. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
16
Repair an open or high resistance in the ground circuit of the center high mounted stop lamp. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
17
Repair an open or high resistance in the stop lamp switch signal circuit of the stop lamp switch. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 20
--
18
Verify the stop lamp switch adjustment. Refer to Stop Lamp Switch Adjustment . If OK, replace the stop lamp switch. Refer to Stop Lamp Switch Replacement .
Did you complete the repair?
Go to Step 20
--
19
Replace the center high mounted stop lamps. Refer to High Mount Stop Lamp Replacement .
Did you complete the repair?
Go to Step 20
--
20
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jun 23, 2017 | Cars & Trucks

1 Answer

Why is the high mount stop light not working?


The same 15amp fuse for the regular brake lights powers the high mount light. If the regular brake lights work but the high mount does not, it could be the lamp monitor or a wiring problem.

Aug 02, 2014 | 2003 Toyota Corolla

1 Answer

Removing tail light housing on a 1998 chevrolet c1500 van


1 Remove the upper quarter panel appliue
2Remove the nuts(2)that retain the tailam to the upper quarter panel
3Remove the center high mounted stop;am(2)from the center high mounted aplique

Feb 27, 2013 | Cars & Trucks

1 Answer

How do you replace a bulb for the high mount stop light


every car i ever had always had light bulb replacement explained in the owners manual, even the high stop lights. buy a used manual on eBay and read it.

Jan 21, 2011 | 2004 Nissan Quest

1 Answer

HOW DO I CHANGE THE BULB FOR THE HIGH MOUNT STOP LIGHT?


From the Owners Manual

Here's what the Owners Manual has to say about the high-mount brake light replacement:


  1. Pry the light assembly away from its housing and push rearward to disengage it from the retaining clips.
  2. Lift the front of the light assembly from the parcel shelf
  3. Disconnect the light assembly wiring and replace the light assembly.

Oct 25, 2010 | 2005 Ford Taurus

1 Answer

Need to replace stop light


Tail Lamp Assembly Removal & Installation To Remove:
Tail lamp assembly removal and installation gm-06-00-1645.gif

  1. Remove the tail lamp assembly retaining screws from the body.
  2. Release the locking pins by pulling the assembly directly rearward.
  3. Disconnect the tail lamp assembly connector.
  4. Remove the tail lamp circuit board from the assembly.
To Install:
  1. Install the tail lamp circuit board into the assembly.
  2. Connect the tail lamp assembly connector.
  3. Push the assembly directly forward into the opening to engage the locking pins.
  4. Install the tail lamp assembly retaining screws into the body. Torque the screws to 17 in-lb (1.9 Nm).
High Mount Stop Lamp Removal & Installation To Remove:
CAUTION
Raising the liftgate with the liftgate window open can damage the high mount stop lamp, liftgate hinges, and the liftgate window.
  1. Raise the liftgate.
  2. Lower the rear of the headliner by removing the rear headliner pins.
  3. Disconnect the high mount stop lamp connector.
  4. Remove the high mount stop lamp grommet from the body.
  5. Lower the liftgate.
  6. Open the liftgate window.
  7. Remove the high mount stop lamp retaining screws from the liftgate window molding.
  8. Remove the high mount stop lamp from the vehicle.
To Install:
  1. Place the high mount stop lamp onto the vehicle.
  2. Install the high mount stop lamp retaining screws into the liftgate window molding. Torque the screws to 22 in-lb (2.5 Nm).
  3. Close the liftgate window.
  4. Lift the liftgate.
  5. Install the high mount stop lamp grommet into the body.
  6. Connect the high mount stop lamp connector.
  7. Install the rear of the headliner by inserting the retaining pins.
prev.gif next.gif

Oct 18, 2010 | 2004 GMC Envoy

2 Answers

Wondering how to change the third brake light (one located in back window) on a 2006 hyundai sonata


High Mounted Stop Lamp Removal & Installation To Remove:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Disconnect battery negative cable.
  2. Disconnect high mounted stop lamp electrical connector from inside trunk.
  3. Remove package tray.
  4. Replace bulb from package tray.
To Install:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Install package tray.
  2. Connect high mounted stop lamp electrical connector from inside trunk.
  3. Connect battery negative cable.
prev.gif next.gif

Oct 12, 2010 | 2006 Hyundai Sonata

1 Answer

Changing high mounted stop light bulb


HMS Lamp will be mounted in roof or in rear parcel tray.

You have to locate the screws which will be closed/covered by a dummy cap. Remove the cap and unscrew the assembly, you will be able to replace the bulbs

Jun 05, 2010 | 2006 Hyundai Sonata

1 Answer

2002 Chevy Tahoe: Replacing Bulbs in Rear High Mount Stop Light?


Yes you can do this your self. When you open the back hatch their should be a way to take out the whole back light system, which then you can replace each individual light.

Jul 01, 2009 | 2002 Chevrolet Tahoe

1 Answer

How do I replace the bulb in the high mount stop light?


Please look at the bottom of your tail lights there is 1 flat head screw there. Take it out and you can slide tail light out. You will find the back of the bulb there. Be care when returning the assembly back in place as it slide up and then you just replace the screw.

Mar 15, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
2004 Chrysler Concorde Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...