Question about 1999 Pontiac Montana

1 Answer

I need to know how to remove the outside, door mirror.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 691 Answers

Very easy job....just pop off inside plastic mirror cover, be very easy due to the cover is held by plastic tab, once the cover is off you will see the bolt that hold it in, just remove it.

Posted on Oct 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How to replace side mirror


Outside Mirrors REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. NOTE: This procedure is for power mirrors. The procedure for a manual mirror is the same with the exception of the lack of electrical wiring.
  2. Remove the door trim panel, plastic fasteners from the sound insulator and water deflector, as required.
  3. Unfasten the retainer, then remove the mirror trim panel. Fig. 1: The outside mirror has a trim panel which is secured with a screw and a retaining clip 89630g19.jpg
    Fig. 2: Unfasten the retaining screw . . . 89630p19.jpg Fig. 3: . . . then remove the mirror finish panel. Note the panel retaining clip (see arrow) 89630p10.jpg
  4. Disconnect the wiring connector and remove the wiring from the door retaining tabs. Fig. 4: Exploded view of the outside mirror cable routing 89630g20.gif

  5. Remove the mirror retaining nuts/screws, then remove the mirror with insulator and wiring. Fig. 5: Pull the sound absorber filler pad out of the door 89630p11.jpg Fig. 6: Unfasten the side view mirror retaining nuts and bolts 89630p12.jpg Fig. 7: Exploded view of the outside mirror assembly mounting 89630g18.jpg
    To install:
  6. Refit the mirror with insulator and wiring into position.
  7. Install the mirror retaining nuts/screws.
  8. Route the wiring through the door retaining tabs and reconnect the electrical connector. Make certain the wiring harness does not interfere with the window glass operation.
  9. Install the water deflector, sound insulator and door trim panel, as required.
  10. Connect the negative battery cable. prev.gif next.gif

Nov 05, 2010 | 1997 Pontiac Bonneville

1 Answer

Replace passenger mirror


glass and motor availbable separately

Removal
NOTE: Do not remove the mirror assembly when repairing the individual mirror part. Individual mirror parts can be installed without removing the mirror assembly.
  1. Remove the front door trim panel; refer to Section 501-05.
  1. Remove the outside rear view mirror access water shield.
    gn1881a.gif
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect and remove the speaker.
    gn1882a.gif
  1. Disconnect the outside rear view mirror electrical connector.
    gn1883a.gif
  1. Remove the outside rear view mirror.
    1. Remove the nuts.
    1. Remove the outside rear view mirror.
      • Feed the outside rear view mirror wiring through the opening in the front door.
    gn1884a.gif

Oct 26, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




  1. Remove the wire clip.
  1. Disconnect the power outside rear view mirror electrical connector.




  1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal
  1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws.


    Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure. Mirror Control
Removal
  1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


May 13, 2010 | 1995 Mercury Villager

1 Answer

I need to know how to replace the side mirror on my 2003 Chevy Tahoe. It is a heated mirror and I need to replace the whole unit. I especially need to know how to take off the door panel to unhook the old...


Well, technically you dont have to remove the door panel to remove the outside door mirror. At the top of the door panel, at the front of the door, there is a triangle shaped plastic cover. It's held in place with push clips, so pull that cover off and remove the foam insulation and you'll be able to access the 3 nuts that hold the mirror to the door. The only potential problem could be in unplugging the wiring harness. I use a hooked pick to pull up the harness to unplug it.

Dec 30, 2009 | 2003 Chevrolet Tahoe

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

1 Answer

I need to know the distance that the drivers side mirror protrudes from the curvature of the door? and also if the outside drivers mirror is molded plastic into the frame of the car?


The outside mirrors attach to the door frame using 3 nuts that attach to studs that are part of the mirror. You can access the attachments by opening the door and removing the triangular shaped plastic trim piece, removing a piece of foam insulation and then you can see the three nuts to remove.

Oct 28, 2009 | 2002 Chevrolet Cavalier Coupe

1 Answer

Need instructions to replace drivers side rear view mirror glass.


Outside Mirrors REMOVAL & INSTALLATION The mirrors on these models can be removed from the door without disassembling the door liner or other components. Both left and right outside mirrors may be either manual, manual remote (small lever on the inside to adjust the mirror) or electric remote. If the mirror glass is damaged, replacements may be available through your dealer or a reputable glass shop in your area. If the plastic housing is damaged or cracked, the entire unit will need to be replaced. Manual
  1. Remove the set screw and the adjustment knob, if equipped.
  2. Remove the delta cover; that's the triangular black inner cover. It can be removed with a blunt plastic or wooden tool. Don't use a metal prytool; the plastic will be marred.
  3. Fig. 1: Use a tapped ended tool to pry the trim from the mirror 89550g29.gif

  4. Depending on the style of mirror, there may be concealment plugs or other minor parts under the delta cover — remove them.
  5. Support the mirror housing from the outside and remove the three bolts or nuts holding the mirror to the door.
  6. Remove the mirror assembly.
  7. Installation is the reverse of removal.
  8. Power
    1. Turn the ignition key to the OFF position. Disconnect the negative battery cable. Wait at least 90 seconds from the time the negative battery was disconnected to start work. CAUTION
      Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in Section 6.
    2. Remove the delta cover; that's the triangular black inner cover. It can be removed with a blunt plastic or wooden tool. Don't use a metal prytool; the plastic will be marred.
  9. Depending on the style of mirror, there may be concealment plugs or other minor parts under the delta cover — remove them.
  10. Depending on the type of door trim, you may need to remove the door inner panel to access the electrical wiring harness for the mirror.
  11. Support the mirror housing from the outside and remove the three bolts or nuts holding the mirror to the door.
  12. If the wiring to the electric mirror was not disconnected previously, detach it now. Some connectors can only be reached after the mirror is free of the door. Remove the mirror assembly.
  13. Installation is the reverse of removal. Cycle the mirror several times to make sure that it works properly.

Jul 23, 2009 | 1996 Toyota Camry

1 Answer

How do I remove the left side mirrer on my 2000 ford explorer?


Mirror — Outside Rear View Removal
NOTE: Do not remove the exterior mirror assembly when repairing an individual part. Individual components can be installed without removing the exterior mirror.
  1. Disconnect the battery ground cable (14301).
  1. Remove the front door trim panel; refer to Section 501-05.
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect the electrical connector.
    1. Remove the speaker.
    gk6980a.gif
  1. Remove the outside rear view mirror (17682).
    1. Disconnect the power mirror wiring clips.
    1. Remove the outside rear view mirror nuts.
    1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).
    gn0316a.gif
Installation
  1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    To install, reverse the removal procedure.
    gn0317a.gif

May 29, 2009 | 2000 Ford Explorer

1 Answer

How to change door mirror


remove the triangle shaped trim pannel on the inside of the door, above the door trim pannel, this will reveal a couple 3-4 nuts that need to be taken off, support the mirror from the outside, once those nuts have been removed, the mirror will be free to be removed, NOTE: if the vehicle is equipped with power mirrors you will need to free the power clip before you remove the mirror

MIKE

May 18, 2009 | 2004 Ford Taurus

Not finding what you are looking for?
1999 Pontiac Montana Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...