Question about 1991 Mitsubishi Eclipse

1 Answer

Clutch wont work

I replaced my clutch which made it work for a little while than it went out again. the pedal goes to the floor and the shifter wont go into any gear.

Posted by on

  • nuke_taz Oct 02, 2009

    fluid was full. tried bleeding it but it didnt help.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 855 Answers

Check and make sure you have fluid in the clutch master cylinder. If it is low fill and check for leaks. Repair leaks as needed and bleed system. If fluid was full check adjustment and bleed system, if there is air in the system pedal will go to the floor.

Posted on Oct 02, 2009

  • Ronald Park
    Ronald Park Oct 02, 2009

    Then in that case the slave or master cylinder is bad. Check and make sure you are getting pressure at the slave. Also another possible answer is the pressure plate.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car wont start


is there a cable that hooks to the clutch,it may be broken.it will need to be re attached or replaced if this is the problem

Dec 30, 2013 | 2006 Peugeot 405

1 Answer

Clutch wont return


Does the clutch pedal not return?

Oct 07, 2013 | Cars & Trucks

1 Answer

I have a 1996 honda civic clutch goes all the way to the floor and wont shift when running only when it is off. got ran off he road the other day went up a pretty high curb and thats when i niticed the...


Your master and slave cylinder can cause this, try replacing the kit for them and if that does not work then u might need to bu a new clutch.

Aug 19, 2012 | 1996 Honda Civic

1 Answer

Workingpedal on floor


clutch pedal? if so sounds like the slave cyl on the transmission needs replacing

Aug 11, 2012 | 2004 Chevrolet Cavalier

1 Answer

I have a 98 vw passat. about a week ago the clutch went to the floor. i reached down and pulled it back up but again it went to the floor and stayed there. i tried this several times before i took off...


hi,
The problem would be the master clutch cylinder that needed to be replace or the replacement cup kit that must be replace!

Go to ur nearest garage to have the replace it or check on it!

Apr 11, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

When i turn the key the engine wont turn over but i have power to everything but the motor


is the car a manual transmission or an automatic? if manual there is a switch on the clutch pedal that wont let engine turn over unless clutch is pushed to floor.automatic it is mounted on transmission at the linkage.for auto trans you can move shifter back an forth while trying to crank engine. if manual you can push clutch pedal to floor hard an try to crank.

Mar 21, 2011 | 1988 Ford Mustang

1 Answer

Clutch wont work pedal goes to floor and hear ratcheting sound


cluth plate and pressure plate bad,,,noise is more than likely loose clutch material scraping some part,,,how long since new parts installed?? not real expensieve,,but moderate amount of money., if you do it yourself. some have inspection plate you can see a little around flywheel housing,,to possibley survey damage. wipe finger in there and see how much material you get,,a lot,,,replace clutch and pressure plate

Jan 21, 2011 | 1983 Chevrolet S-10

1 Answer

Replacing a master and slave clutch cylinders on a


remove the battery and the battery tray,the fluid line and the two bolts that hold on the clutch master and remove.you may need to bleed the new one at the slave cylinder by having someone depress the pedal and letting the air out and tighten the line again before they release the pedal,but i think by pushing the pedal up and down a few times it will be ok. if the shifter wont go into gear or the car starts to move when only slightly moving the pedal of the floor then bleed it.

Feb 20, 2010 | 1993 Ford Escort 4 Door

1 Answer

Clutch pedal goes to the floor, then after pulling it up there is pressure...


There is either air in the system or a leak in the clutch slave cylinder. Check your fluid make sure it is full and the cap is tight.

Sep 18, 2008 | 1996 Pontiac Sunfire

Not finding what you are looking for?
1991 Mitsubishi Eclipse Logo

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...