Question about 1997 Chevrolet Blazer

1 Answer

Cannot get to the wiring to remove a starter - 1997 Chevrolet Blazer

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 141 Answers

Diconnect battery.remove both starter bolts pull back a few inches and then twist it so you can get at the solenoid and battery wires with a long extension....good luck ...Lee

Posted on Oct 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starter removal


remove battery terminals to prevent unexpected grounding of wires at starter. Remove wires at starter, taking note of how they are placed on the starter/selonoid... remove starter mounting bolts, remove starter. Get new starter and install same as reverse. Sometimes the starter has exhaust or other things in the way, so you may have to turn the starter just a certain way to remove it. Might have to come out the top, but out the bottom is the most common way to remove the starter. replace battery wires and vroooom.. off you go.

Dec 17, 2013 | 2002 Hyundai Santa Fe

1 Answer

Change out starter


Starter - 4 Cylinder 112139431
  1. Release hood latch and open hood.
  2. Disconnect and isolate the battery negative cable.
  3. Remove the air cleaner box.
  4. Remove the lower bolt.
  5. Remove the upper bolt and ground wire
Starter Removal - 4 Cylinder 112139432
  1. Remove starter.
  2. Disconnect solenoid wire connector from terminal
  3. Remove nut holding B+ wire to terminal.
  4. Disconnect solenoid and B+ wires from starter terminals.

Jan 01, 2011 | 2004 Dodge Stratus

1 Answer

Starter diagram for a 1994 dodge intrepid


3.3L Engine
  1. Disconnect the negative (-) battery cable. Raise and safely support the front of the vehicle on jackstands. Fig. 1: Disconnect the negative battery cable 88172g31.gif

  2. Remove the three bolts attaching the starter to the engine/transaxle. Fig. 2: Remove the three starter mounting bolts 88172g32.gif
    CAUTION
    Be careful when removing the starter motor mounting bolts, the motor can be quite heavy. Personal injury could result if the starter motor falls from its mounting position.
  3. Remove the starter from the the transmission housing. Position the starter to gain access to the wiring connectors.
  4. Remove the battery positive cable nut from the starter and remove the cable. Fig. 3: Remove the battery positive cable nut from the starter and remove the cable 88172g33.gif

  5. Disconnect the push on solenoid connector.
  6. Remove the starter from the vehicle. To install:
  7. Clean all wire terminals of dirt, grease or corrosion.
  8. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  9. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  10. Lower the vehicle.
  11. Connect the negative (-) battery cable.
3.5L Engine
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. For easier servicing, do not remove the wiring from the starter motor at this time.
  4. Remove the three bolts attaching the starter to the engine. Fig. 4: Remove the three bolts attaching the starter to the engine 88172g34.gif

  5. Remove the starter solenoid assembly from the transfer housing. Position the starter to gain access to the wiring connectors.
  6. Remove the battery positive cable nut from starter and remove the cable.
  7. Disconnect the push on solenoid connector.
  8. Remove the starter from the vehicle. To install:
  9. Clean all wire terminals of dirt, grease or corrosion.
  10. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  11. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  12. Lower the vehicle.
  13. Connect the negative battery cable.
prev.gif next.gif

Oct 15, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

How do you remove the wires from the solenoid of a 1995 S-10 chey with a 4.3L w engine? How is the starter removed really.


remove batter cable from batter. follow postive wire down to starter. Should be some "clips" holding wire into place on the waay down to starter. Loosen those clips and take the wire out. Remove wires from stater. Remove two starter bolts. Job is done. By removing the wires out of those clips you give yourself enough slack to easily do this job. If there still isn't enough room for you, it's not suggested but occsaionaly done, once those wires are removed from the clips, remove starter bolts, the starter will hang by the wires while you remove the wires. This can damage the wires and maybe the solenoid on the new starter. That's why it's NOT SUGGESTED.

Jul 21, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

How do you remove a 1999 Nissan Altima starter?


Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation
  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Apr 05, 2010 | 1999 Nissan Altima

1 Answer

I need to fix a starter on my car


3.1L Engine
Besides regular hand tools, a special oil pressure sensor socket will be necessary to complete this operation.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the A/C compressor brace (if equipped).
  4. Extract the wiring harness from the retainer and position it out of the way.
  5. Remove the cover from the starter wiring.
  6. Remove the outer nut and disengage the wiring from the starter solenoid.
  7. Disconnect the electrical connector from the oil pressure gauge sensor.
  8. Using the special socket, remove the oil pressure gauge sensor.
  9. Unbolt the starter from the engine. Retain any shims.
To install:
  1. Install the starter to the engine, reuse any shims that were removed. Tighten to 32 ft. lbs. (43 Nm).
  2. Connect the wiring to the solenoid and install the outer nut.
  3. Place the cover over the starter wiring.
  4. Replace the oil pressure gauge sensor using the special socket.
  5. Plug the electrical connector onto the sensor.
  6. Mount the harness to the retainer.
  7. Install the A/C compressor brace (if equipped).
  8. Lower the vehicle.
  9. Connect the negative battery cable.

3.4L Engine
This starter is serviced only as a complete unit.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Disconnect the electrical connectors at the starter.
  4. Remove the converter cover.
  5. Remove the starter motor mounting bolts, and remove the starter.

To install:
  1. Install the starter motor to the engine using the mounting bolts. Torque the bolts to 35 ft. lbs. (47 Nm).
  2. Install the converter cover.
  3. Reconnect the electrical connections to the starter.
  4. Lower the vehicle.
  5. Connect the negative battery cable.

3.8L Engine
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Remove the cover from the starter wiring.
  4. Remove the outer nut and wiring from the starter solenoid.
  5. Remove the screws retaining the wiring harness clips and position the harness out of the way.
  6. Take out the screw that retains the plastic flywheel cover and remove the cover from the vehicle.
  7. Remove the bolts retaining the starter to the engine block, and remove the starter from the vehicle.

To install
  1. Install the starter and tighten the bolts to 32 ft. lbs. (43 Nm).
  2. Install the plastic flywheel cover and screw
  3. Reposition the wiring harness, and screw in the retaining harness clips.
  1. Reconnect the wiring to the solenoid and install the outer nut.
  2. Replace the cover over the starter wiring.
  3. Lower the vehicle.
  4. Connect the negative battery cable.

Jan 19, 2010 | 1994 Pontiac Trans Sport

1 Answer

Starter replacement on 1997 dodge intrepid


Disconnect battery negative cable Remove and Install Battery Cable
Raise vehicle.
For easier servicing, do not remove the wiring from starter at this time.
Remove three starter attaching bolts from engine/transaxle Starter -
Remove starter assembly from transmission housing. Position the starter to gain access to the wiring connectors.
Remove the battery positive cable nut from starter and remove the cable Wire Terminal Connections .
Remove the starter from vehicle.
INSTALLATION
For installation, reverse the above procedures. Clean corrosion/dirt from the cable and wire terminals before installing wiring to the solenoid.Thank you for using FixYa,Lee Davidian

Jan 11, 2010 | 1997 Dodge Intrepid

1 Answer

Where is starter located and how to remove it , for a dodge caravan 1998,3.3l


Starter - Removal & installing
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Disengage the solenoid wiring connector from the terminal. This connection may be held in place by a retaining nut, or it could be a push-in connector.
  4. Remove the B+ nut and wire from the starter motor terminal.
  5. Remove the starter motor-to-transaxle bellhousing mounting bolts.
  6. Remove the starter from the vehicle. If equipped, remove the starter motor spacer.
To install:
  1. If equipped, hold the starter motor spacer in position.
  2. Install the starter motor into position on the vehicle.
  3. Install the starter motor-to-transaxle bellhousing mounting bolts. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  4. Engage the solenoid wiring connector onto the starter terminal.
  5. Connect the B+ wire and tighten the retaining nut to 90 inch lbs. (10 Nm).
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Verify starter motor operation.
020fef8.jpg

Disengage the solenoid wiring connector, then the battery positive (B+) nut and wire from the starter motor

98933b2.jpg

Remove the 3 starter motor-to-transaxle bellhousing mounting bolts

e2afde4.jpg

Remove the starter motor from the vehicle


The starter relay is located in the Power Distribution Center (PDC) in the engine compartment. Refer to the underside of the PDC cover for starter relay location.

Hope helped with this (remember rated this help) Good luck.

Nov 18, 2009 | 1998 Dodge Grand Caravan

2 Answers

What procedures do I take when removing and installing a new starter? 1991 lexus ls 400


Let engine cool down, remove battery terminals (negative first, then positve), remove starter. Install starter, install battery terminals (positive first, then negative), start and check for proper operation (no grinding noise or squeling).

Apr 03, 2009 | 1991 Lexus LS 400

1 Answer

Starter


hi clarence,

first of all you need to know what is the starter in order to remove it. if you can trace the big wire that comes from the positive wire of your battery to a big round thing at the bottom part of the engine. that round thing is the starter. before you start removing bolts, remove first that big wire from the positive terminal of the battery. it is normally bolted to the engine by three or two bolts. there are two wires that you need to remove first before removing the starter. a big wire from the battery and a small wire that controls the solenoid of the starter. after you remove the wire, remove the bolts that is holding the starter in place and the starter would drop down. the you can repalce it or repair it.

i hope i was able to solve your problem. please rate me.. tnx.

drcool299

Jul 09, 2008 | 1987 Nissan Stanza

Not finding what you are looking for?
1997 Chevrolet Blazer Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...