Question about 1994 Honda Passport

1 Answer

How do you remove rotors - 1994 Honda Passport

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 92 Answers

Pull the wheels.

disassemble the pads/calipers.

pull the rotors.

reinstall calipers/pads.

reinstall wheels.

Posted on Oct 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2005 gmc yukon denali rotor removel


Brake rotor and front or rear?

Okay, remove the wheel then remove the brake caliper and move to side do not allow to hang on the brake hose, use a hook to hang off spring or set aside. next remove the caliper bracket, two bolts at rear of bracket to remove it.
next you will use a hammer to remove the rotor.

NOTE: the way the brake rotor was designed was a bad one the hub in which the rotor slides over and the wheel studs slide into holes on the rotor is bad the hub diameter is almost the same size as the diameter of the seat of the rotor that slide over the hub and what happens is sometimes the rust build up on the rotor seat locks the brake rotor on the hub. i do not know if you are reusing the rotors or replacing them, no sure what job you are doing . the rotors to take off you will need to tap on the rear of them with a little force and turn, hit and turn. you will need to see if they break free or if hard beating and spraying into the rear of them is needed with wd40.
Alot of these rotors also have two threaded hole on the face of the rotor near the studs so that you can screw two bolts into holes to help pull them. use wire to tie caliper up and also use a c-clamp to push piston into calipe to remove caliper if needed, Do not remove brake hose, there is no need to open system, here is a picture of the rotor coming of the hub, also there may be clips on the stud holding rotor on remove them use cutters or pry off do not need to reuse , they are to help in holding the rotor on during asm, if you want you can buy them and reinstall them but never reuse them.12_25_2012_5_41_09_pm.png

Dec 25, 2012 | 2003 GMC Yukon XL

1 Answer

How to remove front brake rotor


Is this 4wd or 2wd? The 4wd will just require the removal of the caliper it has a full floating rotor.If you are replacing the rotor and the rotor is stuck on you can use a ball peen hammer and hit the face of the rotor but only do this if replacing it and be sure to wear eye protection.


The 2wd will require you to remove the caliper then the centercap in the middle of the rotor.There you will see a cotterpin that needs removed.Once cotterpin is removed there will be a nut that needs to be unthreaded.Once the nut is removed the rotor will slide right off.

Jan 03, 2011 | 1998 GMC Sierra

1 Answer

How do I remove the rotor on my 1995 dodge 2500 4x4? My problem in the center cap holding it.


Brake Disc (Rotor) REMOVAL & INSTALLATION
  1. Raise and safely support the front of the truck with jackstands. Remove the front wheel.
  2. Remove the caliper assembly and support it to the frame with a piece of wire without disconnecting the brake fluid hose.
  3. Remove the hub and rotor assembly.
  4. Install the rotor in the reverse order of removal, and adjust the wheel bearing as outlined in Section 1.
INSPECTION If the rotor is deeply scarred or has shallow cracks, it may be refinished on a disc brake rotor lathe. Also, if the lateral run-out exceeds 0.010 in. (0.25mm) within a 6 in. (152mm) radius when measured with a dial indicator, with the stylus 1 in. (25mm) in from the edge of the rotor, the rotor should be refinished or replaced. A maximum of 0.020 in. (0.5mm) of material may be removed equally from each friction surface of the rotor. If the damage cannot be corrected when the rotor has been machined to the minimum thickness shown on the rotor, it should be replaced. The finished braking surfaces of the rotor must be parallel within 0.007 in. (0.178mm) and lateral run-out must not be more than 0.003 in. (0.076mm) on the inboard surface in a 5 in. (127mm) radius. Fig. 1: Use a dial indicator and micrometer to check the rotor for run-out and thickness 88479g83.gif
Fig. 2: A correct final rotor finish 88479g84.gif
Fig. 3: Location of the rotor minimum thickness marking 88479g91.gif
Fig. 4: Exploded view of a rotor mounting to the hub — 4WD Dakota models shown 88479g90.gif
prev.gif next.gifprev.gif next.gif

Sep 03, 2010 | 1995 Dodge Ram 2500

1 Answer

Cant get the rotor off of a 99 , any suggestions


Remove the brake caliper, and caliper holder if it goes over the rotor. If it's 2 wheel drive, remove the center cap, take out the cotter pin. Remove the nut holding on the rotor. If it's 4 wheel drive, once you remove the associated brake parts, spray some WD-40 around the studs and the center of the rotor, try striking the rotor with a rubber hammer. Often the rotor will rust to the hub, on the 4 wheel drives. The 2 wheel drives, have the rotor with the hub for the bearings together, the 4 wheel drive has a "top hat" type rotor.

Mar 10, 2010 | 1999 Dodge Ram

1 Answer

How to replace 99 gmc 3/4 tom brake rotors


Removal & Installation
  1. Remove 2/3of the brake fluid from the master cylinder.
  2. Raise and support the vehicle.
  3. Remove the tire and wheel assembly.
  4. Remove the front wheel hub extension (dual wheel vehicles only).
    • Insert a drift or large screwdriver through the brake caliper into one of the brake rotor vanes in order to prevent the rotor from turning.
    • Mark the relationship of the front wheel hub extension to the hub
    • Remove the front wheel hub extension bolts
    • Remove the front wheel hub extension from the vehicle. It may be necessary to tap around the perimeter of the hub extension with a rubber mallet to loosen it from the hub
  5. Mark the relationship of the rotor to the hub.
  6. Remove the caliper and mounting bracket as an assembly.
  7. Hang the caliper and the mounting bracket assembly from the suspension using mechanics wire.
  8. Remove the rotor.
  9. If the rotor is difficult to remove due to corrosion in the hub area use the following procedure to remove the rotor (25 series only).
    • Clean all the surface areas and the threaded holes of contamination
    • Generously apply penetrating oil or the equivalent to the hub/rotor area
    • Insert (2) M10 x 1.5 bolts (jack screws) into the threaded holes of the rotor
    • Tighten both bolts evenly to force the rotor from the hub.
c3692a2.gif
To install:
  1. Clean all rust and contaminants from the both side of the rotor and the hub flange.
    NOTE If the rotor was removed using the jack screw method you must ensure that the hub flange is free of nicks or marks caused by this procedure. Remove all raised nicks or marks before installing the rotor.

  2. Install the rotor.
  3. Install the caliper and the mounting bracket as an assembly.
  4. Install the tire and wheel assembly.
  5. Remove the safety stands.
  6. Lower the vehicle.

Oct 25, 2009 | 1999 GMC Sierra

1 Answer

How to replace front rotors on a 1989 190e mercedes?


Remove tyres. Remove brake pads.
Remove Brake calipers bolts from the back of calipers.
Put calipers aside without removing brake lines. Remove rotor bolts. Remove rotors. Install new rotors Make sure new rotors are clean from any grease that comes on it with petrol or any cleaning chemical for that purpose (no water) Install calipers Install new brake pads Good luck

Oct 20, 2009 | 1989 Mercedes-Benz 190

1 Answer

How do you remove rotors 2000 4runner front...thanks nick


With 4x4? remove wheel on hub you will see a cover with about 6 bolts remove bolts, remove cover. Then remove snapring this snapring keeps axle in place remove screws that hold wahser that sets load on bearings remove rotors and separate from hub as hub needs to be transfered to new rotors, do so by removing bolts hub to rotors. you may have to use pry bar to separate hub from rotor

Jul 07, 2009 | Toyota 4Runner Cars & Trucks

2 Answers

Im trying to install a new rear hub assembly and cannot get the rotor off. Any sugestions.


Remove the rotors. Rusted rotors will most likely stick to the car due to the iron oxidizing and bonding to the mount of the wheel. If this happens, you are going to need a little force to remove the rotor from the wheel. With the car properly secured, get a single-hand sledge mallet (rubber preferably to protect the rotor). If you don’t have a rubber mallet, use a block of wood to absorb direct hits. Start at the top of the rotor and tap the edge of the rotor gently as you move clockwise around the rotor. Once loose, remove the rotor from the car.

Feb 17, 2009 | 2004 Mitsubishi Endeavor

1 Answer

1998 honda civic front rotor replacement


Varvah, front rotor: Jack up the car, put on safety stands, remove wheel, remove caliper mounting bolts (2), hang caliper in place w/ bungy cord, rope, etc. so you don't stress the brake line, remove caliper mounting bracket bolts, remove bracket from rotor, remove retaining screws on the front of the rotor, remove rotor. If it's stuck, get 2 - 8x 1.25 mm screws (longer version of what u removed), tighten them in the rotor, they will push it off easily. Reverse to install, tighten bracket to 80 ft lbs, caliper to 20 ft lbs. Let me know if u need more info. Countrycurt0

Oct 09, 2008 | 1998 Honda Civic

1 Answer

93 honda accord rotors


Your Accord has what is called "Trapped Rotors". They actually fit behind the hub. The procedure to remove them is not complicated, but it is time consuming.
Here is how I do it:
1) Remove axle retaining nut.
2) Remove brake caliper and bracket.
3) Remove lower ball joint retaining nut and use pickle fork to loosen spindle from lower ball joint.
4) Remove axle from hub.
5) On the back of the spindle, remove four bolts that attach hub/bearing to spindle.
6) Use slide hammer to remove rotor/hub assembly.
7) Remove 4 bolts attaching rotor to hub.
8) While it is a snug fit, the hub bearing does slide through center of rotor to remove it.
Installation is in reverse order.
A bad bearing usually makes a growling noise while driving.

Jun 06, 2008 | 1993 Honda Accord

Not finding what you are looking for?
1994 Honda Passport Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...