Question about 1998 Dodge Ram

1 Answer

How do you remove the cooling fan - 1998 Dodge Ram

Posted by on

  • yankstorm02
    yankstorm02 May 11, 2010

    You can access free repair manuals online @ google ebooks and autozone.com

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

First you take off the belt then remove bolts from fan pully then remove fan and shroud at the same time

Posted on Oct 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove and replace the water pump on a 2006 Chrysler 300 hemi 5.7 l.


5.7L Engines

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Drain the cooling system.
  4. Disconnect negative battery cable.
  5. Remove the upper radiator hose.
  6. Disconnect cooling fan electrical connector.
  7. Remove cooling fan mounting bolts.
  8. Remove the radiator cooling fan assembly from vehicle.
  9. Remove the radiator fan assembly.
  10. Remove accessory drive belt.
  11. Remove thermostat.
    NOTE The water pump mounting bolts are different lengths. Note the location of the water pump mounting bolts.
0996b43f80200d65-mw3da2o1okphbx00ygfzxzdl-4-0.jpg To install:
  1. Install water pump and mounting bolts. Tighten mounting bolts to 20 ft. lbs. (28 Nm).
  2. Make sure double ended bolt is in the proper location. Tighten double ended bolt to 20 ft. lbs. (28 Nm).
  3. Position the radiator cooling fan assembly in vehicle.
  4. Install cooling fan mounting bolts. Tighten to 50 inch lbs. (6 Nm)
  5. Connect the cooling fan electrical connector.
  6. Install the upper radiator hose.
  7. Install thermostat.
  8. Install the accessory drive belt.
  9. Install the radiator fan assembly.
  10. Connect negative battery cable.
  11. Fill the cooling system.
  12. Pressure test cooling system.

Mar 16, 2017 | 2006 Chrysler 300

1 Answer

How to change a coolant fan for a 2001 impala


  1. Disconnect the negative battery cable.
  2. Partially drain the cooling fan.
  3. Raise and support the vehicle. Refer to Vehicle Lifting.
  4. Remove the transmission oil cooler lines from the retainers at the bottom of the cooling fan shroud.
  5. Remove the lower fan shroud push pin retainers.
  6. Lower the vehicle.
  7. Remove the right and the left engine mount struts.
  8. Remove the left front fender upper diagonal brace.
  9. Remove the radiator inlet hose from the radiator.
  10. Remove the air cleaner assembly.
  11. If equipped remove the cooling fan heat shields.
  12. Disconnect the cooling fan shroud electrical connectors.
  13. Remove the cooling fan shroud bolts.
  14. Disengage the cooling fan shroud clip from the top of the radiator.
  15. Remove the cooling fan shroud.


25010346-uuob5xk5qpmufdktz2iyu4qm-2-0.gif

Aug 25, 2014 | 2001 Chevrolet Impala

2 Answers

2002 jeep grand cherokee larado is over heating. The cooling fanonly runs if I hotwire it. I changed th thermostat. Temp gauge is reading . Could it be the cooling fan relay if so where is it located. The...


Fan relay is located under pass headlight. Remove light assembly, use 2 1/2 " hole saw to drill hole in plastic housing ,3"from back wall, 3'' from left side.This will put you right over relay. Unscrew two bolts,replace. Relay was $40.... dealer wanted$350 to remove front bumper to replace it.

Sep 02, 2010 | 2002 Jeep Grand Cherokee

1 Answer

2005 Jeep Liberty overheats at idle but while in movement temp returns to normal.


Check to see if the fan on the radiator is working at idle.

Here's information on how to change the fan if needed:

Engine Cooling Fan Removal & Installation 2.4L Engine To Remove:
  1. Remove the coolant bottle and set aside.
  2. Remove the power steering reservoir and set aside.
  3. Disconnect the cooling fan connector.
  4. Remove the cooling fan mounting screws and the cooling fan.
To Install:
  1. Install the cooling fan and the mounting screws. Tighten to 50 in-lb (5.5 Nm).
  2. Connect the cooling fan connector.
  3. Install the power steering reservoir.
  4. Install the coolant bottle.
3.7L Engine To Remove:
NOTE: If the fan blade is bent, warped, cracked or damaged in any way, it must be replaced ONLY with a replacement fan blade. DO NOT attempt to repair a damaged fan blade.
NOTE: For 3.7L Heavy Duty/Max Cool/Trailer Tow cooling package, the viscous fan cannot be removed separate from the shroud. Both fan and shroud must be removed together.
  1. Disconnect battery negative cable.
  2. Using special tool #6958 spanner wrench and #8346 adapters, remove the viscous fan from the water pump.
  3. Gently lay fan into shroud.
  4. Disconnect the electrical connector for the electric fan, then disconnect connector from shroud.
  5. Remove the two fan shroud mounting bolts connecting the fan shroud to the radiator.
  6. Remove the shroud and fan from the vehicle.
To Install:
  1. Install fan shroud assembly into the vehicle. Tighten fan shroud to radiator bolts to 50 in-lb (5.5 Nm).
  2. Install shroud mounting bolts tighten bolts to 89 in-lb (10 Nm).
  3. Connect fan motor wire connector to harness connector, and attach connector to shroud.
  4. Connect negative battery cable.
  5. Start engine and check fan operation.

Aug 31, 2010 | 2005 Jeep Liberty

1 Answer

How to change the radiator fan?


Electric Engine Fan - Fan Switch

Removal & Installation
2.7L Engine
  1. Disconnect negative battery cable.
  2. Partially drain cooling system.
  3. Disconnect the electrical connector .
  4. Remove engine coolant sensor from coolant outlet tube .
To install:
  1. Apply thread sealant to sensor threads.
  2. Install engine coolant temperature sensor into coolant outlet tube.
  3. Tighten sensor to 20 ft. lbs.(28 Nm) torque.
  4. Connect electrical connector to engine coolant temperature sensor .

3.2L And 3.5L Engines
  1. Disconnect negative battery cable.
  2. Partially drain cooling system.
  3. With the engine cold, disconnect coolant sensor electrical connector.
  4. Remove sensor.
To install:
  1. Install engine coolant temperature sensor.
  2. Tighten sensor to 20 ft. lbs.(28 Nm) torque.
  3. Attach electrical connector to sensor.
  4. Connect negative battery cable.
Removal & Installation
  1. Disconnect negative battery cable.
  2. Partially drain cooling system.
  3. Remove upper radiator hose.
  4. Disconnect cooling fan electrical connector.
  5. Remove cooling fan mounting bolts.
  6. Remove radiator cooling fan assembly from vehicle.

    f9d971c.jpg
    Fig. Removal and installation of the radiator fan-2.7L Engine shown
To install:
  1. Position radiator cooling fan assembly in vehicle.
  2. Install cooling fan mounting bolts. Tighten to 50 inch lbs. (6 Nm)
  3. Connect cooling fan electrical connector.
  4. Install upper radiator hose .
  5. Fill cooling system.
  6. Operate engine until it reaches normal operating temperature.
  7. Check cooling system and automatic transmission for correct fluid levels.

Hope helps (remember comment and rated this).

Jul 13, 2010 | 2001 Dodge Intrepid

1 Answer

How do you change the cooling fan



Electric Engine Fan

Cooling Fan Connectors

Removal & Installation
2.2L& 2.4L Engines
  1. Disconnect the negative battery cable.
  2. Remove the hood close out filler retainers.
  3. Remove the hood close out filler panel.
  4. Remove the upper radiator mount bolts.
  5. Remove the upper two hood latch support bolts.
  6. Remove the two lower hood latch support bolts.
  7. Raise the vehicle.
  8. Remove the cooling fan mounting bolt.
  9. Disconnect the electrical connector from the cooling fan. Remove the cooling fan assembly.

To install:
  1. Install the cooling fan assembly.
  2. Connect the electrical connector to the cooling fan.
  3. Install the cooling fan mounting bolt. Tighten the bolt to 53 inch lbs. (6 Nm).
  4. Lower the vehicle.
  5. Install the lower two hood latch support bolts. Tighten the bolts to 20 ft. lbs. (27 Nm).
  6. Install the two upper hood latch support bolts. Tighten the two upper hood latch support bolts to 80 inch lbs. (9 Nm).
  7. Install the upper radiator mount bolts. Tighten bolts to 89 inch lbs. (10 Nm).
  8. Install the hood close out filler panel.
  9. Install the hood close out filler panel retainers.
Removal & Installation
  1. Disconnect the negative battery cable.
  2. Remove the hood close out filler retainers.
  3. Remove the hood close out filler panel.
    CAUTION Be careful when you handle a sensor. Do not strike or jolt a sensor. Before applying power to a sensor:
    0e518e2.jpg

    Fig. Remove the hood close out filler retainers and the hood close out filler panel
    1. Remove any dirt, grease, etc. from the mounting surface
    2. Position the sensor horizontally on the mounting surface
    3. Point the arrow on the sensor toward the front of the vehicle
    4. Tighten all of the sensor fasteners and sensor bracket fasteners to the specified torque value.
  4. Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.
  5. Disable the air bag sensor.
  6. Remove the upper radiator mount bolts.
  7. Remove the upper 2 hood latch support bolts (2).
  8. Remove the 2 lower hood latch support bolts (4).
  9. Raise the vehicle.

    581eb59.jpg
    Fig. Remove the cooling fan mounting bolt
  10. Remove the cooling fan mounting bolt.
  11. Disconnect the electrical connector from the cooling fan.
  12. Remove the cooling fan assembly.
To install:
  1. Install the cooling fan assembly.
  2. Connect the electrical connector to the cooling fan.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the cooling fan mounting bolt and tighten the bolt to 53 lb inches (6 Nm).
  4. Lower the vehicle.
  5. Install the lower 2 hood latch support bolts and tighten the bolts) to 20 ft. lbs. (27 Nm).
  6. Install the 2 upper hood latch support bolts and tighten the bolts to 80 lb inches (9 Nm).
  7. Install the upper radiator mount bolts and tighten bolts to 89 lb inches (10 Nm).
  8. Engage the air bag sensor.
  9. Install the hood close out filler panel.
  10. Install the hood close out filler panel retainers.
  11. Connect the negative battery cable.
Hope this help (remember comment and rated this).

Apr 14, 2010 | 2001 Chevrolet Cavalier

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    1 Answer

    How do i replace the radiaor? on this 2005 Hyundai do i remove the intake cover, then the cooling fan, the the motor mount? what?


    Below are instructions and a diagram for removing the radiator from your Santa Fe. There's nothing involving the motor mounts. Best of luck and please post back with any questions or just to rate the solution. Greg

    1. Drain the cooling system. Remove the radiator cap to speed draining.
    2. Remove the inlet hose from the radiator.
    3. Remove the transmission oil cooler lines from the retainer clip at the bottom of the cooling fan shroud.
    4. Remove the fan shroud clip from the condenser tubes.
    5. Remove the bolt that connects the fan shroud to the condenser hold down bracket.
    6. Remove the air deflectors from the top of the radiator.
    7. Remove the cooling fan shroud bolts.
    8. Remove the coolant reservoir hose from the radiator overflow neck.
    9. Remove the radiator upper support brackets and bolts that connect to the fan shroud.
    10. Disconnect the engine cooling fan motors electrical connectors.
    11. Remove the cooling fan motors electrical harness from the fan shroud clips.
    12. Remove the cooling fan shroud.
    13. Remove the outlet hose from the radiator.
    14. Disconnect the transaxle oil cooler pipes from the radiator.
    15. Tilt the top of the radiator rearward.
    16. Remove the condenser hold down bracket from the radiator.
    17. Lift the condenser from the mounting tabs on the radiator and position the condenser aside.
    18. Remove the radiator.
    6db9db4.gif

    Aug 11, 2009 | 2005 Hyundai Santa Fe

    1 Answer

    RADIATOR REPLACEMENT


    • At the time of installation, please refer to the following items.
    • Start the engine, and check for coolant and A/T fluid leaks.
    • Check the A/T fluid level.
    1. Drain engine coolant.
    2. Canada: Disconnect relay block (for daytime running light system) from battery hold-down clamp.
    3. Disconnect upper radiator hose from radiator.
    4. Disconnect lower radiator hose from water inlet pipe.
    5. Disconnect A/T oil cooler hoses from oil cooler pipes.
    6. Disconnect No.1 and No.2 cooling fan connectors.
    7. Disconnect No.1 Engine Coolant Temperature (ECT) switch wire connector.

    8. Remove radiator and cooling fans assembly.
      1. Remove the 2 bolts and 2 upper supports. Torque: 12.8 Nm (9 ft. lbs.)
      2. Lift out the radiator, and remove the radiator and cooling fans assembly.
      3. Remove the 2 lower supports.
    1. Remove A/T Oil cooler hoses from radiator.
    2. Remove lower radiator hose from radiator.
    3. Remove No.1 ECT switch.

    4. Remove No.1 cooling fan from radiator. Remove the 2 bolts and cooling fan. Torque: 5.0 Nm (44 inch lbs.)
    5. Remove No.2 cooling fan from radiator. Remove the 3 bolts and cooling fan. Torque: 5.0 Nm (44 inch lbs.)
    INSTALLATION
    Installation is in the reverse order of removal.

    Nov 06, 2008 | 1992 Lexus Es 300

    Not finding what you are looking for?
    1998 Dodge Ram Logo

    Related Topics:

    30 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    75077 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7768 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...