Question about 1998 Toyota Tacoma

2 Answers

Needs more power for a 98 toyota tacoma 4 cylendar

Needs more power just doesn't go fast enough need higher gears like about 50 in first 100 in second an so on i have only had it to about 140

Posted by on


2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 101 Answers

If ur talking 50 mph in just first gear etc,Go see Don Gartlet or a Nascar Team

Posted on Oct 02, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Toyota Master
  • 2,050 Answers

Install nitrous, four turbo's and raise the compression to14:1. Then install 1:1 gearing. (A jet engine may also help.)

Posted on Oct 02, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

98 Toyota Tacoma 4 cylinder 5 speed pops out of gear how do I fix

Suspect worn shift detent or synchronizer. Recommend tranny shop

May 20, 2015 | 1998 Toyota Tacoma

1 Answer

Number 4 cyl. misfire/ 2.4rz engine/98 toyota p.u. how to fix misfire of number 4 cyl.on toyota 98 tacoma p.u./2.4rz engine

check compression, check valve clearance, check injector for properly working, check for vacuum leak around this cylinder.

Feb 10, 2015 | 1998 Toyota Tacoma

1 Answer

When im driving my 98 4x4 tacoma, it will violently vibrate at speeds of 40mph and then again at 60mph, then drive simi smooth after...any ideas as to what this could be, U-joint? wheel bearings?

Best guess is worn steering tie rods first. it doesn't take much wear for wheel shake to occur in the 4wd versions. next would be other steering components- idler arm and pitman arm. next would be ball joints- these are probably already needing replacement due to 4wd and age.
Good luck

Aug 24, 2011 | 1998 Toyota Tacoma

1 Answer

5 speed trans 96 tacoma jumping out of gear 1st through 4th gears when you let off the gas

Hi there,

This commonly occurs when either the Shift Linkage is faulty (or simiply needs adjustment), Shifter Fork is loose, or there is excessive movement of the Input Shaft.

Adjusting the shift linkage would be your first task. If this doesn't correct the problem, then you will need to investigate the other 2 components as suggested above.


"If this has helped you in any way, please rate this solution"

May 13, 2011 | 1996 Toyota Tacoma

1 Answer

98 toyota tacoma tipped on the left side

the weak spring is making it tip. also you say the other shock is leaking fluid. you need to replace both shocks and springs, the seem to have been worn down, there is no fix other than using spring blocks to boost up the saging side, but i would recommend replacing it all.

Nov 30, 2009 | 1998 Toyota Tacoma

2 Answers

Have p0130 and p0133 codes 98 toyota tacoma

check the mass air flow sensor there maybe dirt on the filiment inside the sensor causing false readings. cleaning or replacing it may make the codes go away.

Oct 28, 2009 | 1998 Toyota Tacoma

1 Answer

Working on a 98 toyota tacoma v6 4wd 3.4l eng. I

Yes,need to make sure crank is at TDC as well

Oct 09, 2009 | 1998 Toyota Tacoma

1 Answer

Wont start, just clicks.

This problem is caused by the starter motor contacts inside the starter solenoid being worn burned and pitted, U CAN REPLACE JUST THE CONTACTS FOR ABOUT $15, CHECK EBAY MOTORS FOR THE PARTS FOR YOUR YEAR OF TRUCK.

May 22, 2009 | 1998 Toyota Tacoma

1 Answer

2006 Toyota Tacoma V6 engine oil sensor location

There is not enough flow at the sensor for a second oil filter. The sensor is at a dead end in the oil gallery. I recommend that you persue other options here. If you are concerned about oil contamination, don't be. There is nothing better than the factory filter...Look into adding more oil capacity; Look into an engine oil cooler; there is really no need for a second filter.

Sep 07, 2008 | 2006 Toyota Tacoma

Not finding what you are looking for?
1998 Toyota Tacoma Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides