Question about 2001 GMC Jimmy

1 Answer

How to bleed brakes on 2001 Jimmy

I want to bleed my brakes but I do not know on what side to start on.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 521 Answers

Right rear left rear right front left front.

Posted on Oct 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced brake line, rotors and pads bled brakes all around and the brakes when the truck is off work but once i start the truck the brake pedal goes to the floor and have no brakes at...


Bench Bleed the M/C first, then do not let it run dry during system bleeding. Parts stores sell a kit that helps installed m/c bleeding.

Sep 29, 2010 | 2001 GMC Jimmy

1 Answer

My abs & brake lights go on & off brake pedal seems soft brake fluid - ok, no leaks, has new brake lines, slamming on the brakes locks 'em up. no abs, right? 2000 gmc jimmy 4.3


Sounds like you might have air in the brake system. You will need to bleed the brakes to remove air. Start with the passenger back wheel. use a small hose and submerge the end in a glass bottle filled 1/3 full of brake fluid. The other end goes on the nipple of the brake bleeder. Have someone pump the brakes and then hold the pedal down then loosen the bleeder. then tighten the bleeder. you should see bubbles in the brake fluid. Keep repeating this procedure until you see no bubbles. You might have to put as much as 1 quart of brake fluid thru each wheel to remove air. Then you do the driver side rear followed bypassenger side front and finally driver side front

Aug 11, 2010 | 2000 GMC Jimmy

2 Answers

Can not get a pedal, replaced master cylinder twice, bled everything, no pedal...can't seem to get fluid out of the 3 front ports on the master cylinder...could both master cylinders be defective, or am I...


Did you bleed the master cylinder before you put it in the vehicle?This usually makes it easier to bleed the entire brake system if this is done before you install the master cylinder.Other wise all you have done is put air in the brake system.The master cylinder kit usually comes with a bleeder kit.This is for bench bleeding the master.Hope this helps.Good luck.

Dec 31, 2009 | 2001 Chevrolet Tracker

1 Answer

Bleeding brake system how?


BLEED BRAKE SYSTEM

Make sure one end of the Jeep is raised (starting with the rear end) and secure on jack stands and the wheels on each side have been removed. If you have been working on the brakes, this should already be done.

Connect a clear rubber tube to the bleeder valve on the right rear brake caliper. Start with this end and side because it is farthest from the master cylinder.Place the tube's other end into a container partially filled with brake fluid.

Open the bleeder valve on the caliper and have an assistant press on the brake pedal inside the Jeep. Look for a mixture of air and fluid to come out of the valve. Once all the air is purged and the fluid runs cleanly from the valve, close the screw and remove the tube.

Repeat the process for all four brakes. Move to the left rear next, followed by the right front and the left front. If you need to, reconnect the Jeep's rear wheels and lower the rear end before raising the front end and removing those wheels.

Check the level of fluid in the master cylinder periodically as you bleed the brakes. If the level drops below the needed fill line, add more fluid. Use fresh fluid, not any that you have bled from the brakes.

Start the Jeep's engine after bleeding all the brakes and press on the brake pedal. You might need to do this repeatedly to seat new brake pads you just installed. Turn off the engine and hold down on the pedal. Bleed the brakes again if the pedal sink within 15 to 20 seconds.

Dec 21, 2009 | 2001 Jeep Grand Cherokee

2 Answers

Brake pedal still goes to floor 2000 GMC Jimmy


It's very possible to be the master cylinder, the o-rings on the piston could be worn, letting the fluid seep back through instead of getting full pressure through the lines. Could also be the brake booster.
Try changing the master cylinder first, which is cheaper and easier, and see if there is a difference, you'll need to bleed the brakes again.
To check the booster,
With the engine off, pump the brakes until the pedal is hard, then hold pressure on the brake pedal and listen for air escaping, or the pedal goes slowly to the floor, Do that after the master cylinder has been changed, at least that will be eliminated.

Sep 15, 2009 | 2000 GMC Jimmy

1 Answer

How do i properly bleed out my Jimmy?


I use a vacuum bleeder (abt $35) starting at the furthest brake line from the master cylinder & working my way back to the closest. If bled properly by keeping the maste cylinder full, this should solve your problem. Rick

Apr 15, 2009 | 1998 GMC Jimmy

2 Answers

Bleeding Brakes on a 2001 Silverado Z71


Tony,

When bleeding brakes after the system has been opened for service (you didn't say if you were doing any work on the master cylinder) you should start with the farthest wheel away from the master cylinder, which is the righ rear. Fill the master cylinder, then have an assitant "pump up" the brake pedal. Tell them to hold it down firmly, then open the bleeder on the wheel cylinder(s). Do not release the brake pedal until you have closed the bleeder valve again. You'll know when the air is out - there won't be any more bubbles. Since this vehicle is 2001, this would be a great opportunity to flush the system. Just make sure you have enough brake fluid (DOT 3 or 4, depending on your vehicle). Good luck!

Mar 15, 2009 | 2001 Chevrolet Silverado

1 Answer

Rear brakes not completely disengaging


your inside pad wore out first do to a bad caliper or frozen slide or brake hose.remove brake hose off the caliper and see if you can turn the wheel.if you can replace hose and bleed caliper.if wheel still doesn't move buy a loaded caliper,this will come also with new slides!and then bleed

Jan 25, 2009 | 1994 GMC Jimmy

Not finding what you are looking for?
2001 GMC Jimmy Logo

Related Topics:

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...