Question about 1992 Nissan Maxima

2 Answers

Where do you plug the data dianostic connector?

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 521 Answers

Fuse panel...should be a plug in terminal there. If in doubt visit your local autoparts store and they cane tell/show you

Posted on Oct 02, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert that has over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 255 Answers

Under the drivers side dash inside car. obd2

Posted on Oct 02, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2002 Toyota Camey LE Dianostics not reading

check that the data link ( 16 pin connection under the dash) is connected correctly to the ECM . You may have to take it to a Toyota dealer service centre to have the connection problem fixed first. It could be in the wiring., connections or the ECM itself.

Mar 18, 2014 | Cars & Trucks

1 Answer

2003 ford crown vic police car unalbe to do dianostics keeps saying unable to connect to pcm done checked all fuses and wiring looks good

Check pin #16 of diagnostic connector it should have 12 volts. See diagram below. Also did you check the fuses under the hood?

Nov 01, 2012 | Cars & Trucks

1 Answer

Where is the dianostic connector

All OBD2 system test plugs are supposed to be under the dash on the driver side.

Sep 11, 2012 | 2001 Honda Accord

1 Answer

Can't find where to plug in dianostic in freelander exi 1998

Hi there:
The OBD connector is on the left hand side of the centre console. If you run your finger around the left hand side from the cigarette lighter you should find it.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 08, 2012 | Land Rover Freelander Cars & Trucks

1 Answer

Where is the body control module located on a 2007 nissan armada

Along the steering column near the dianostic link connector. lower of the instrument panel

Feb 26, 2012 | Cars & Trucks

1 Answer

Where is the brain box jack for the honda accord 1997 model

Oh, you must mean the diagnostic connector. I think on all post '96 vehicles it's just beneath the dash on driver's side, protruding out a little from bottom edge of the dash.

Nov 12, 2011 | 1997 Honda Accord

1 Answer

Jeep 89 dianostic scanner

the renault designed (pre1991)jeep computer systems were very simple and diagnostic codes were non existant diagnosis is by scan data not codes common failuer parts were oxygen sensors and crank sensors throttle position sensors were failure prone also BUT need to be ajusted correctly to ork properly

Feb 16, 2010 | 1989 Jeep Cherokee

1 Answer

Software program

Most of the time mechanics use a scanner as the programs are (garded) by the vehical manufactures OTC , Snap-on tools. You want a unit that will see the data stream not just retreive and reset codes. Lap-top programs can be shopped for on the internet but the dianostic machaines (scanners) have trobleshooting and different dianostic cables and you may decide that if your going to make this kind of investment in tools them you had better be ready to make a living at it. Alot of stops don't have a laptop program because of the casts ( most dealers have a manufactures interface ) Until there is somekind of breakthough the cast is too high and the updates can be higher

Jan 17, 2009 | 2007 Chevrolet Equinox LS New Cars

Not finding what you are looking for?
1992 Nissan Maxima Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

80608 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides