Question about 1986 Ford F150 SuperCab

1 Answer

I pulled and rebuilt the 302 in my 86 150 and the tranny want shift gears it only has 1st and reverse but thats it i have checked and rechecked all the wireing is good is there a relay or something else that could have gone out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 713 Answers

Check and make sure the torque convertor is locked all the way in on the input shaft. If it is not all the way ingaged it will not shift correctly.

Posted on Oct 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not shift out of 2nd gear


Tranny most likely shot. I believe yours is a T-5, I had the same issue years back but in 3rd gear. Usually the clutch going out is a gradual thing. So I would have a tranny shop look at it. Maybe find a cheap rebuilt tranny for ya.Look online or a trusted shop.

Mar 23, 2014 | 1994 Ford Mustang

1 Answer

1999 3500 dodge 4x4 dually, 47re Tranny. problem existed before and after having my Tranny rebuilt. tried 4 new valve bodies even a new BD VALVE BODY. Truck starts out in 2nd gear when put into...


the transmittion keeps shifting in & out of gear between 45 & 50 mph it shifts to a higher gear then a lower then higher then lower till I get above 50 mph whats the problem & how to fix it

May 03, 2011 | 1999 Dodge Ram

2 Answers

1994 GMC 1500 Sierra has to rev up 1st gear and let off to get to shift from 1st to 3rd gear. Had tranny rebuilt. Could problem be solved by changing the ECM Engine Control Module or Transmission...


If reverse is ok then you have a bad shift solenoid b.There are two solenoids on the back of the valve body that are identical,it will be the one on the pasenger side.GM calls them the 1-2 and 2-3 shift solenoid but this is deceptive because it takes a combination of them being on or off to achieve every gear.Pull the pan, disconnect solenoids and check resistance across them with a volt meter.I think you are looking for less than 20 ohms but the bad one will be off the chart.Bad transmission controllers are very rare in a GM vehicle.I bet if you have codes pulled you will find a shift solenoid code.Good luck!

Feb 21, 2011 | 1994 GMC Sierra

2 Answers

1994 Cadillac Deville - won't shift into reverse after sitting overnight or for a couple of hours. Will shift into 1st and then will shift into reverse. What is causing this?


Check the transmission fluid level, reverse needs twice the pressure to activate that drive does. If low refill and try again. If fluid good, I`d say the tranny 3rd reverse clutch is worn out. Recheck the condition of the fluid on the dipstick, if it appears burnt or very dirty I`d still suspect internal tranny clutch issues. It also has a low reverse clutch, but goes into 1st gear as you said.

Feb 02, 2011 | 1994 Cadillac DeVille

1 Answer

I HAVE 99 ISUZU RODEO 2WD LOST 1ST & 2ND


if your close or over 100,000 miles, better to have the tranny rebuilt.

Nov 07, 2009 | 1999 Isuzu Rodeo

1 Answer

2004 pt cruiser shifts in all gears but reverse.


yes, it is an indiscator that the friction discs are wearing out - take to a local tranny shop and have them check the fluid - it may cost the price to have tranny rebuilt which is about
$2000.00

Sep 15, 2009 | 2004 Chrysler PT Cruiser

4 Answers

Transmission will not shift into 1st gear or reverse


check you shift silinoids, there located inside trans mission pan on back of valve body. there are 2 of them.swap them with each other,if you have 1st &reverse then you know its one of the siliniods. if it makes no difference then you need to have your trans rebiut or get a new one.

Jul 26, 2008 | 1988 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...