Question about 1997 Ford F250 SuperCab

1 Answer

How do you loosen serpertine belt on f250 diesel 1997

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 127 Answers

Get a breaker bar into the square hole in the tensioner and try rotating it both ways until it starts to let the belt go. Once it gets loose enough slip the belt off.

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 areostar serpertine belt diagram replacement


open hood look at the radiator and the serpertine diagram is right there,it in yellow and black

Aug 29, 2010 | 1996 Ford Aerostar Extended

1 Answer

Need to replace the idle pulley on a ford f250


if it is a 7.3 or 6.0 turbo diesel it will have a duallie tensioner-pulley setup. use a half inch breaker bar or ratchet to grab a hold of the tensioner then turn it very firmly counter clockwise until you can remove the belt. after that use the corresponding size socket and ratchet to loosen the bolt that retains the idler pulley.

Nov 18, 2009 | 2002 Ford F250 Super Duty SuperCab

2 Answers

Can i add fluid to the rear differential on my 1997 f250 powerstroke?


Yes, you should be able to add it thru the level check plug, which I believe is removed with a 1/2 inch drive extension that should fit in the plug, and just loosen and remove. To be at the correct level, the gear oil should just start to flow out of the plug hole. And of course, for an accuracy, do this on a level surface.

Jul 31, 2009 | 1997 Ford F250 SuperCab

1 Answer

What will a 1997 f250 7.3 diesel with 3.55 gears pull? (auto)


Check the dealer's website. They should be able to tell you the towing rate.

Jun 15, 2009 | 1997 Ford F250 SuperCab

1 Answer

2000 f250 diesel, how do you release the tension on the belt?


There is a tensioner idler somewhere on the engine. Use a wrench and rotate the bolt in the center so that the pulley moves away from the belt, then use the other hand to slide the serpentine belt out from under the idler.
Slowly release the tensioner.

Jan 22, 2009 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Diagram for serpentine belt for 1992 ford f250 7.3 diesel


First off---Have you looked under the Hood for the Factory Belt Routing Sticker? If not there look in the Owners Manual. If not there let me know so that I can Locate you one.

Jan 20, 2009 | 1992 Ford F250

1 Answer

I need to know the steps for uninstalling, and reinstalling the alternator on a 1989 Volvo 240 DL.


Steps

1. Disconnect the battery
2 Loosen botls so you can remove the drive belt to alternator.
3. If it has a serpertine belt, then pry with proper tool on the tensioner to remove the belt.
4. Disconnect harness to alternator and ground wire if any and filter condenser if any.
5. Loosen bolts to alternator and remove alternator.
6. If AC equipped, not knowing your belt configuration would require to loosen the AC Belt also, depending if your alternator belts is the first one near the engine, then all belts have to be loosen to remove it. unless #3 applies.
Reverse the steps to put it back on.

Dec 26, 2008 | 1989 Volvo 240

1 Answer

Replacing Serpertine Belt


the diagram is located in the engine, at the front along with other engine information stickers, u also need the proper tool to pull the pulley forward

Aug 15, 2008 | 1997 Oldsmobile Cutlass Supreme

1 Answer

2004 F250 Turbo Diesel alternator pulley


the belt tensioner is on the lower left of the engine there is a 1/2 drive square hole on the right hand side pulley arm to release the tension its a pain to get at but you can, sometimes it is easier from the bottom

Jul 31, 2008 | 2004 Ford F250

1 Answer

What tools do you need to replace a 1997 Ford F250 diesel fuel pump?


nothing special, its in the valley, probably have to remove the fuel bowl and the turbo pedastal to get access to it.
book value from navistar / ford is a 4 hour job.
better have a good ladder and a plywood sheet to lay on up in the engine bay.

Jul 05, 2008 | 1997 Ford F250 SuperCab

Not finding what you are looking for?
1997 Ford F250 SuperCab Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...