Question about 2007 Isuzu Ascender 7 Passenger

1 Answer

How can i program my new keyless entry fob for my Isuzu Ascender

Could someone give me step by step directions for programing my fob

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 36 Answers

If it is a new key fob it will have to be programmed by the dealer.
This is the statement as listed in the owners manual for your vehicle.

Matching Transmitter(s) to Your Vehicle
Each remote keyless entry transmitter is coded
to prevent another transmitter from unlocking
your vehicle. If a transmitter is lost or stolen, a
replacement can be purchased through your dealer.
Remember to bring any remaining transmitters with
you when you go to your dealer. When the dealer
matches the replacement transmitter to your
vehicle, any remaining transmitters must also be
matched. Once your dealer has coded the new
transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have a maximum of four
transmitters matched to it.
94

Posted on Oct 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 crown vic keyfob only works with ignition in run position .keyless entry and door locks work fine.even tried new keyfob.no change


The keyless entry system consists of the following components:
  • driver door module (DDM)
  • keyless entry transmitter
  • keyless entry keypad
The driver door module (DDM) receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
  • Battery junction box (BJB) fuses:
    • circuit breaker 7 (20A)
  • Central junction box (CJB)
    • 4 (10A)
    • 6 (15A)
    • 8 (25A)
    • 13 (5A)
  • Keyless entry keypad switch
  • Power door lock actuator
  • Luggage compartment release switch
  • Luggage compartment release solenoid
  • Connectors or connections
  • Wiring harness
  • If fuse's good have checked for DTC'S - diagnostic trouble codes .
  • B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L Need a professional grade scan tool to check fro these codes . Not a code reader for OBD2 codes .
  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter not programmed.
  • Remote transmitter.
  • DDM.
  • Go To Pinpoint Test F .

Did you program the new key fob ?

Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.
  1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.
  1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
  1. NOTE: Failure to wait at least 20 seconds will cause programming failures. Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification

Feb 19, 2017 | Cars & Trucks

1 Answer

Programming key fobs for a 2007 Silverado


If Your 2007-2010 Silverado Has a VIC - Vehicle Information Center Step 1: Sit in the vehicle with all the doors closed and unlocked. Start your Silverado and leave it in Park.
Step 2: Press and hold the Vehicle Information button, marked by an image of a car and the letter "i", until the display reads "Press V to Relearn Remote Key".
Step 3: Press the Set/Reset button until "Remote Key Learning Active" appears.
Step 4: Simultaneously press and hold the Lock and Unlock buttons for 15 seconds. A chime will sound indicating the remote has been successfully programmed.
Step 5: Program additional remotes by repeating Step 4 for each fob.
Step 6: Exit programming mode by turning off the vehicle and removing the key.
Step 7: Test your remote(s).
If Your 2007-2010 Silverado Doesn't Have a VIC - Vehicle Information System Step 1: Sit in the vehicle with all the doors closed and unlocked. Turn the key to Accessory Power position.
Step 2: Press the trip odometer meter reset stem repeatedly until you see "Relearn Remote Key".
Step 3: Press and hold the trip odometer meter stem for three seconds. The display will read "Key Learning Active".
Step 4: Simultaneously press and hold the Lock and Unlock buttons for 15 seconds. A chime will sound indicating the remote has been successfully programmed.
Step 5: Program additional remotes by repeating Step 4 for each fob.
Step 6: Exit programming mode by turning off the vehicle and removing the key.
Step 7: Test your remote(s).

Nov 02, 2016 | Chevrolet Silverado Cars & Trucks

1 Answer

Is there a way to reset keyless entry for 04 endeavor?


Search Results

    2004 Mitsubishi Endeavor Key Fob Remote Programming ...

    blog.keylessentryremotefob.com/.../04/2004-mitsubishi-endeavor-key-fo...
    Apr 25, 2013 - 2004 Mitsubishi Endeavor Key Fob Remote Programming Instructions ... you might have visit us at Keylessentryremotefob.com You can also ...

    Mitsubishi - Free Keyless Remote Fob Entry programming .

    How To Replace Mitsubishi Endeavor Key Fob Battery 2004 ...

    ? 2:04
    www.youtube.com/watch?v=yeQRdre7O0Q
    Oct 31, 2014 - Uploaded by Keyless Entry Remote Inc
    ... will show you How To Replace Mitsubishi Endeavor Key Fob Battery 2004 2005 To Order This Remote ...

Nov 01, 2015 | Cars & Trucks

1 Answer

Can I program the car to recognixe the key fob.


1996 Roadmaster

  1. Locate the programming connector located in the LH trunk. Trim may have to be pulled back to access programming connector. ( Connector has black/white wires leading up to it and it is not connected to anything.)
  2. Jump programming connector terminals. Leave terminals jumped unitl step 6.
  3. System should now lock and unlock doors to indicate programming mode has been entered.
  4. Press any button on keyless remote once. System should now lock and unlock doors, indicating successful programming of keyless remote.
  5. Repeat step 4 for additional remote or other existing keyless remote. NOTE: A maximum of only two Keyless Remotes can be programmed.
  6. Remove programming connector jumper wire to exit programming mode.
  7. Test remote(s).

Oct 19, 2015 | 1996 Buick Roadmaster

1 Answer

How do I program new key if I buy one not programmed


Basic programming on fobs, if they are self-programming, will be in the book in the glove box.It will give you step-by-step instructions for your car, or tell you to go to the dealer.

Mar 26, 2015 | Cars & Trucks

1 Answer

My 2006 Toyota Tundra SR5 will not go into program mode to program my keyless entry pads


The security system on Toyota products are added by the distributor in your region. Many of those security systems will not allow more than 4 key fobs to be programmed into them. Have you owned this vehicle since it was new? Have you tried to program more that 4 key fobs into it? Have you tried programming it more than 2 times? If you security system has had more than 4 key fobs programmed in then the only way to get it to reprogram is the replace the security unit with a new one. I found this out the hard way and had to replace mine in my 2000 tundra.

Aug 03, 2012 | Toyota Cars & Trucks

1 Answer

Hello, I have a 1994 Xj6 Jaguar. I've purchases a new keyless entry clicker with directions to program it but after follwing them I've had no luck. My mechanic also tried and had no luck. Does anyone


i have the official jaguar manual and it doesnt even mention this procedure ,i will go to yard and get my alldata book ,Right it says they can only be programmed using diagnostic equipment so please dont blame the messenger

Nov 20, 2011 | Cars & Trucks

1 Answer

Replaced chip on key on 91 DTS and car lost all power while driving. It shut down and nothing works.


There are 4 methods for programming key fobs. Up to 4 key fobs may be programmed to the remote control door lock receiver (RCDLR). Each programmed key fob is given a position of #1-#4 in the RCDLR memory.
Method 1 - Key Fob Quick Learn This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
Place the replacement key fob in the console fob pocket with the buttons facing forward.
A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 2 - Key Fob Slot Programming

This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Install a scan tool.
Use the scan tool, to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 3 - Key Fob Auto Learn

This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 4 - Service Programming System Fob Programming

This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the fobs can be programmed similar to Method 2 using slot programming. A scan tool, Techline Terminal, and a replacement key fob are required to perform this procedure.

Place the vehicle in the Vehicle On, Engine Off mode.
Connect a scan tool to the vehicle.
Insure that all power consuming devices are turned OFF on the vehicle.
With a scan tool, select Request Info under Service Programming System and follow the scan tool on-screen instructions.
Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
Turn the vehicle OFF.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions. Ensure the correct programming procedure is selected based on component being replaced or programmed. See Important above.
Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
With a scan tool, select Program ECU under Service Programming System.
At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
When the 10 minute relearn procedure has completed, use the scan tool to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 12-13, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.

Oct 26, 2011 | 2006 Cadillac DTS

1 Answer

How to program new keys for my 2005 impala


You can do it.Its not very hard to reprogram the key fobs.Take note that your remote key fob battery is fine and not discharged/drained.Otherwise the procedure will not give proper results. For exact step by step procedure, Click the link below :--- http://howtobyme.blogspot.com/2011/10/how-to-program-new-keys-for-2005.html ---------- This should help.Thanks.Helpmech.

Oct 24, 2011 | 2005 Chevrolet Impala

Not finding what you are looking for?
2007 Isuzu Ascender 7 Passenger Logo

577 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75824 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...