Question about 1997 Dodge Intrepid

1 Answer

Need tourque for 97 dodge intrepid engine heads. engine is 3.5

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,674 Answers

Perform it in 4 steps.
first- 45 ft.lbs
2nd- 65 ft.lbs.
3rd- 65 ft lbs again.
4th- 1/4 turn more.
After 4th step, you should have more than 90 ft.lbs. if not, replace bolt.
Also make sure you do proper sequence, as well as check all bolts (unless you bought all new) to make sure they haven't been stretched. Use a straightedge and lay threads on it to make sure they all touch straightedge.

Posted on Oct 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LOUD engine noise sounds like the upper left part of the 3.3l 97 dodge intrepid engine......possible problems/solutions


Most likely sludge causing valve train issues

Short of removing the heads & going thru them
& all parts removed,don't know

I have watched some of that, a couple days ago
on You Tube

Oct 03, 2012 | Cars & Trucks

1 Answer

My 97 dodge intrepid 3.5 liter engine is smoking out the front of the engine not the exhaust. Can you tell me what is the Rear Main Seal and what is the Head Gasket and where to look for the two? If I knew...


The rear main seal is between the engine and transmission. Head gaskets are what seals the block and head of the motor. If the smoke is sweet smelling I would assume it to be a misting coolant leak from a small hole in the radiator. Even though that car is front wheel drive it's mounted longitudinally. Hope this helps.

Jan 20, 2011 | 1997 Dodge Intrepid

1 Answer

I need to know the sequence to tighten cylinder head bolts on a 97 dodge intrepid 3.5 6 cylinder


First, torque them all to 45 ft pounds(61 nm), second to 65 ft pounds (88nm) go over them a third time @65 ft pounds again. then 1/4 turn and you are done.

Sep 14, 2010 | 1997 Dodge Intrepid

1 Answer

How do i find the fuel relay for a 97 dodge intrepid


There is a fuse box on the drivers side of the car near the battery. Remove the cover by pushing down on the clip on the engine side of the box. The lid should have the locations of each Relay. They are all the same part, just in different locations.

May 19, 2010 | 1997 Dodge Intrepid

2 Answers

My 97 intrepid is idle to hight


I'm guessing this Intrepid is a 3.5 cause I have never had this problem with a 3.3 But what I found what always caused it in a 3.5 is bad intake gaskets allowing more air to flow into the engine. Change both upper and lower intake gaskets and this should fix the problem. However when changing the lower intake gaskets there are two bolts that are probably gonna give you problems. The one closest to the front and the one closest to the back. They are the bolts that hold the intake down and go into the head near the coolant ports. These bolts are probably going to break off. The good news is they most of the time break off and there is still a lot of bolt left once you get the intake off to get a vice grips on. Have a torch with a good heating tip handy and someone that really knows how to use it and heat the cyl head around the bolt and then try to get it out with the vice grips, but be very careful cause heating aluminium can be very tricky too much heat and you ruined the head.

Feb 25, 2010 | 1997 Dodge Intrepid

1 Answer

Could I replace a blown 97 Dodge Intrepid engine for one that works, but is year 94?


That is possible but the computer system in the '97 is much different than the '94. So there will be allot (large list) of parts to change over from the old engine to the new one. A '96 engine would be more compatible than a '94 but still some differences.

Dec 30, 2009 | 1997 Dodge Intrepid

1 Answer

Trying to find tourque for 97 dodge intrepid engine heads. engine is 3.5


get a manual and make sure that the they dont have to be new

Oct 02, 2009 | 1997 Dodge Intrepid

2 Answers

Need a 3.5 engine mounting diagram for 97 dodge intrepid and 2.7 engine mounting diagram for 02 dodge intrepid


Google 1997 Dodge 3.5 liter Engine Mounting Diagram. Same for the 2002 engine. I guarrantee you will find it.For some strange reason you would'nt call your local Dodge dealer and ask them where you can go to on the web and locate it.

Jan 06, 2009 | Dodge Intrepid Cars & Trucks

Not finding what you are looking for?
1997 Dodge Intrepid Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...