Question about 1999 Jeep Cherokee

1 Answer

How to replace noisy belt tensioner on 94 Jeep Cherokee

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

Remove the belt and un bolt it

Posted on Oct 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, how to relieve the belt tension on jeep grand cherokee 1995?


Hi,


In order to relieve the belt tension in your cherokee jeep,you have to locate the belt tensioner pulley first, which is found between the crankshaft and a component toward the top of the hood area.

Afterwards,Rotate the belt tensioner pulley, using a wrench spanner to relieve the tension on the belt.



Good luck.

Aug 20, 2010 | 1995 Jeep Grand Cherokee

2 Answers

I need to replace my serpentine belt. Which


For a 94 Jeep grand cherokee, the tension is controlled through a long bolt on the power steering bracket. The bolt is about 6 inches long, located underneath the power steering on the driver side. Lossen the lockbolt holding it in place, as well as the Power steering attach bolts, and turn the long bolt to tighten/loosen. I believe these are all 13 mm bolts.

Jun 30, 2009 | 1994 Jeep Grand Cherokee

2 Answers

Jeep cherokee country tensioner pulley noise


May be a weak tensioner that needs replacing. Make sure you clean pulleys well with brake cleaner or similar as well. I have had one with similar problem, that Gator back belt was causing it. I'm not 100% convinced that a notched belt will get as good a grip as a complete rib all the way around the belt. Just doesn't add up to me. If you compare that to tire grip, then you'd be telling me that snow tires would work better on the Nascar circuit?

Jun 28, 2009 | 1997 Jeep Cherokee Country

1 Answer

1998 Jeep Grand Cherokee - Multi-rib belt Removal & Replacement


Check on upper rad shroud or under hood for routing diagram. Depending on what engine, procedure may vary a little. I wouldn't panic on replacing anything other than belt unless you noticed something noisy under hood in last while.
If not up to it, a mechanic should be able to do it for you in a few minutes usually, but won't hurt to ask before, just in case.

Jun 27, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Adjust wiper arm tension on 94 Jeep Grand Cherokee


there is no tension adjustment if the arm is too loose and dosen't put enough pressure on the windshield you need to replace the arm you can bend the center of the arm very slightly and get a little more tension BUT the arms are over 15 years old and teh springs are probably weak

Apr 20, 2009 | 1994 Jeep Cherokee Country

1 Answer

2000 jeep grand cherokee 4.0 liter engine timing belt replacement


If you have the same pulley arrangement that most 4.0 engines have that pulley is an idler not a tensioner. Your power steering pump has a pivot bolt, and a slide under the pump. You adjust belt tension using the pump.

Apr 04, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Whining noise


Could be a few things:

Belt slipping- adjusted through tensioning bolt on bottom of power steering pump

Pulleys- take off belt and hand turn pulleys. Find one that gives resistance and possible makes the whining noise. It's probably the idler pulley.

Feb 12, 2009 | 1994 Jeep Cherokee Country

1 Answer

Serpentine belt wont stop slipping


sounds like your belt tensioner pulley may be defective, also check all the pulleys for excessive play in the pulley bearings, these are the most common causes.

Feb 05, 2009 | 1994 Jeep Cherokee

1 Answer

I HAVE A 94 JEEP GRAND CHEROKEE, BATTERY WILL NOT HOlD CHARGE. I REPLACED ALTERNATOR, BATTERY AND ALL CABLES. STILL WILL NOT START WITHOUT JUMP RUNS FOR 5 TO 10 MILES DIES WITH DEAD BATTERY. WHAT ELSE...


Check the Belt Tensioner. If the Tensioner is not Keeping the Belt Tight it will Drain the Battery Pretty Fast.Please Rate my Response, I need all the Help That I can Get! Thanks!

Jan 27, 2009 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Jeep Cherokee Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...