Question about 1991 Toyota Xtracab

1 Answer

Cannot get starter motor out of chassis, motor bolts are removed, wires disconnected yet it has no room to actually get out

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

There is a four bolt plate on the inner fenderwell that can be removed 10mm socket.

Posted on Oct 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change a starter for a 99 grand am se? Do you have any schematics that illustrate?


the starter is located on the front side of motor and is bolted to the transmission with two bolts. Raise the front of vehicle enough to get under and have room to work, block car securely before climbing under. disconnect the positive battery post from battery, proceed to remove starter and then remove wires from starter. to install hook wires to same locations they were removed from and install starter motor, install positive battery post connection and done.

Jan 19, 2011 | 2001 Pontiac Grand Am SE

1 Answer

Trying to change a 1998 Isuzu Rodeo v6 2WD starter and I'm looking for step by step instructions. Help?


1. Detach the cable from the negative terminal of the battery.
2. Raise the vehicle and support it securely on jack stands.
3. If you can reach them, disconnect the battery cable and solenoid connector from the starter motor solenoid. On some engines the terminals are difficult to reach while the starter is installed; it's actually easier to unbolt the starter, pull it out to point where you can reach and disconnect the cables.
4. Remove the starter motor bolts and detach the starter from the engine. Having socket swivels and extensions, along with angled wrenches, will make this job easier. Depending upon the year and engine type, the starter may be mounted above the transmission or below the intake manifold. On some models it may be necessary to remove the exhaust system to make room for the starter assembly to pass between the engine and chassis. Make sure the engine and exhaust system are cool before starting. I found that once you get the cables off, you have a better chance to remove the starter motor without removing the exhaust system. If you have to mess with the exhaust system, just loosen enough to allow clearance.
5. Install in the reverse order. If it was necessary to remove the starter to disconnect the cables, remember to maneuver the replacement starter in place, ensuring that you have the necessary access/clearance through the exhaust system, and reconnect the cables prior to bolting the starter in place.
6. Be patient. With the right tools and a little luck this shouldn't take more than an hour once you have the vehicle on jack stands and the engine has cool. It

Nov 16, 2010 | 1998 Isuzu Rodeo

1 Answer

Starter diagram for a 1994 dodge intrepid


3.3L Engine
  1. Disconnect the negative (-) battery cable. Raise and safely support the front of the vehicle on jackstands. Fig. 1: Disconnect the negative battery cable 88172g31.gif

  2. Remove the three bolts attaching the starter to the engine/transaxle. Fig. 2: Remove the three starter mounting bolts 88172g32.gif
    CAUTION
    Be careful when removing the starter motor mounting bolts, the motor can be quite heavy. Personal injury could result if the starter motor falls from its mounting position.
  3. Remove the starter from the the transmission housing. Position the starter to gain access to the wiring connectors.
  4. Remove the battery positive cable nut from the starter and remove the cable. Fig. 3: Remove the battery positive cable nut from the starter and remove the cable 88172g33.gif

  5. Disconnect the push on solenoid connector.
  6. Remove the starter from the vehicle. To install:
  7. Clean all wire terminals of dirt, grease or corrosion.
  8. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  9. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  10. Lower the vehicle.
  11. Connect the negative (-) battery cable.
3.5L Engine
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. For easier servicing, do not remove the wiring from the starter motor at this time.
  4. Remove the three bolts attaching the starter to the engine. Fig. 4: Remove the three bolts attaching the starter to the engine 88172g34.gif

  5. Remove the starter solenoid assembly from the transfer housing. Position the starter to gain access to the wiring connectors.
  6. Remove the battery positive cable nut from starter and remove the cable.
  7. Disconnect the push on solenoid connector.
  8. Remove the starter from the vehicle. To install:
  9. Clean all wire terminals of dirt, grease or corrosion.
  10. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  11. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  12. Lower the vehicle.
  13. Connect the negative battery cable.
prev.gif next.gif

Oct 15, 2010 | Dodge Intrepid Cars & Trucks

3 Answers

How to change the Starter on a 1989 toyota camry


Starter - REMOVAL & INSTALLATION
Gasoline Engines
  1. Disconnect the cable from the negative terminal of the battery.
0856b4b.jpg


Fig. 5: Exploded view of the starter motor mounting-5S-FE engine shown, others similar
  1. On 1992-96 models with cruise control, remove the battery.
  1. Also on 1992-96 models with cruise control, remove the actuator cover and disconnect the wiring harness. Remove the three bolts and then lift out the cruise control actuator. Remove the bracket from beneath the actuator and put aside.
  1. Peel the rubber boot away and remove the nut and disconnect the negative battery cable from the magnetic switch terminal on the starter. Disconnect the electrical connector also located on the magnetic switch.
  1. Support the starter by hand and remove the two mounting bolts.
  1. Remove the starter from the transaxle.
To install:
  1. Place the starter motor in the transaxle and support by hand.
  2. Install the two mounting bolts and tighten them to 29-31 ft. lbs. (39-42 Nm).
  3. Connect the connector to the magnetic switch. Place the battery cable on the switch terminal and install the nut. Tighten the nut and position the rubber boot over the cable.
  4. Using the ignition switch, "bump'' the starter over a few times and check for proper operation.

Hope helps.

Aug 11, 2010 | 1989 Toyota Camry

1 Answer

How to change the starter in a 1998 Mazda 626


1993-98 626/MX-6/Probe Models

2.0L ENGINE

(see Figures 5, 6, 7, 8, 9 and 10)
  1. Disconnect the negative battery cable.
  2. Remove the fresh air duct and resonance chamber.
91a666b.jpg

Fig. 5: To remove the starter motor, first remove any obstructing components, then loosen the upper starter motor attaching bolts

78fd60e.jpg

Fig. 6: Remove both upper bolts before going under the vehicle to finish the removal procedure
  1. Label and disconnect the electrical connectors and remove the air cleaner assembly.
  2. Remove the intake manifold bracket.
1536d13.jpg

Fig. 7: Raise and safely support the front of the vehicle, then label and detach any plug-on wire connectors

59b31de.jpg

Fig. 8: Using the proper size socket or wrench, remove the battery positive wire retaining nut ...

9934705.jpg

Fig. 9: ...and the wire terminal from the starter
  1. Label and disconnect the wiring at the starter.
  2. Remove the starter mounting bolts and remove the starter.
a62a8db.jpg

Fig. 10: Remove the lower starter motor mounting bolt and carefully lower the starter and remove it from the vehicle
  1. Installation is the reverse of the removal procedure. Tighten the starter mounting bolts to 33 ft. lbs. (3 Nm) and the intake manifold bracket bolts to 38 ft. lbs. (8 Nm).

2.5L ENGINE
  1. Disconnect the negative battery cable.
  2. Remove the fresh air duct. Disconnect the electrical connector and remove the air cleaner assembly.
  3. If equipped with automatic transaxle, proceed as follows:
    1. Relieve the fuel system pressure. Drain the cooling system.
    2. Disconnect the accelerator cable from the throttle body. Label and disconnect the electrical connectors, vacuum hoses and coolant hoses from the throttle body.
    3. Remove the throttle body.
    4. Disconnect and plug the fuel supply and return lines.
    5. Disconnect the transaxle selector cable from the transaxle and remove the cable bracket.
    6. Remove the starter bracket.
  4. Label and disconnect the wiring at the starter.
  5. Remove the starter mounting bolts and remove the starter.
  6. Installation is the reverse of the removal procedure. Tighten the starter mounting bolts to 38 ft. lbs. (8 Nm).

Hope this help (remember comment and rated this help). TY for using Fixya.

May 12, 2010 | 1998 Mazda 626

1 Answer

2001 toyota camry wont crank over and the tow truck driver thinks its the timing belt would that be the cause.


Timing belt would not be the reason for the engine not cranking up. A broken timing-belt simply won't let the engine fire up and run.
To get it to crank up would involve having to check the battery plus terminals, the starter-motor, and
maybe the ignition switch.

Starter-Motor Removal:
Have your radio activation code ready if it is equipped with anti-theft.
1. Disconnect the negative battery terminal, then disconnect the positive terminal. You could take out the battery for more room.
2. Disconnect and remove the cruise control assembly from its mount. You would need 10-mm socket and wrench to loosen and remove the bolts.
3.Trace the battery positive wire to the back of the engine, and remove it with a 12-mm socket. Remove the electrical plug connector-this is the solenoid wire.
4. Loosen and remove the starter-motor three bolts.
5. Take the starter-motor for test at a good autoparts store.
6. Replace if found defective, following reverse of removal.

Dec 21, 2009 | Toyota Camry Cars & Trucks

1 Answer

Replace starter


96 probe, 2.0L 4 cylinder. Should be similar to 626 I think.

Starter Motor
Removal


Exploded View of the Starter Motor Mounting Components




  1. stu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When servicing the starter motor or performing other underhood work in the vicinity of the starter motor (11002), be aware that the heavy gauge battery input lead at the starter solenoid is "electrically hot" at all times. A protective cap or boot is provided over this terminal (B-terminal) on all carlines and must be replaced after servicing. Be sure to disconnect the battery ground cable before servicing the starter motor.
    Disconnect the battery ground cable (14301).
  1. Remove the air cleaner (ACL) and the air cleaner to intake manifold tube (9B697). Refer to Section 03-12A for the procedures.
  1. Remove the two upper starter motor bolts.




  1. Raise and support the vehicle.
  1. Remove the intake manifold support bolts and the intake manifold support (9J444).




  1. Disconnect the S-terminal wire.
  1. Remove the B-terminal wire nut and disconnect the B-terminal wire.
  1. Remove the lower starter motor bolt.
  1. Remove the starter motor.

Aug 10, 2009 | 1995 Mazda 626

2 Answers

Removing starter


It's not that easy. Yes, 2 bolts hold the starter down but you have to remove the whole intake manifold to access the starter to remove it.

May 30, 2009 | 2003 Honda Accord

1 Answer

How do you remove the starter?


the starter is located on the drivers side about midway down the side of the motor. there are two bolts that hold it in place, and a couple of wires that are held on by small bolts.
To remove the starter first disconnect the battery and then place the vehicle on a block with the front end elevated just ennough to remove the drivers side front tire. removing the tire should give you enough room to get to the starter through the tire well. then just unbolt the wires and take the two mounting bolts out and the starter should just slip right out. to reassemble just work in reverse order.

May 15, 2009 | 1999 Dodge Durango

1 Answer

Need to replace starter


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect battery negative remote cable from remote ground post.
  3. Raise and safely support the vehicle
Starter Motor

098a02a.gif
    1. Remove or disconnect the following:
    2. Three bolts attaching starter to engine
    • Positive battery cable from starter
    • Starter assembly from transmission housing
    1. Position jack stand beneath engine and slightly lift to relieve pressure from left engine mount.
    2. Remove three left engine mount bolts from engine block.
    3. Jack engine up slightly to give more room to maneuver starter assembly.
    4. Slide rear of starter motor out between catalytic converter and engine mount.
    1. Remove or disconnect the following:
    2. Posi-lock starter solenoid connector.
    • Starter from vehicle.
    To Install:
    1. Install or connect the following:
      • Positive battery cable to starter
      • Posi-lock starter solenoid connector
    2. Jack engine up slightly to give more room to maneuver starter assembly.
    3. Install or connect the following:
      • Starter
        1. Torque to 40 ft. lbs. (54 Nm)
      • Three left engine mount mounting bolts to engine block
    4. Lower vehicle.
    5. Connect the battery negative cable.
  • May 05, 2009 | 1998 Chrysler Concorde

    Not finding what you are looking for?
    1991 Toyota Xtracab Logo

    Related Topics:

    39 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    76682 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8531 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...