Question about 1994 Isuzu Pickup

1 Answer

1994 Isuzu Pickup replace rotor, caliper, repack wheel barrings.

Working on a 1994 Isuzu pickup. Need to remove and replace driver side rotor and caliper. How do I remove the hub? Is a special tool needed? Does it just pop off ? Screw off? Or do I remove the rotor first?? You assistance is greatly apprreciated.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Isuzu Master
  • 2,050 Answers

Remove caliper, then the caliper bracket that supports the pads and caliper. The rotot should have one or two threaded holes near the lug nut studs. You install a bolt here (Correct thread pitch) and thread it in to "pop" off the rotor. (They are usually rusted on.)
Keep in mind that the new caliper needs to have the brake fluid bled.

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

How do I remove the front brake rotors?


Take the brake calipers off, the caliper mount(if applicable) and then hit the sides of the rotor with a heavy hammer until the rotor frees itself.....UNLESS you have 4 wheel drive, then you must disassemble the hub assembly.

Feb 06, 2011 | 1983 Toyota Pickup

1 Answer

How do you get rotors off back of Isuzu 1994 when you got the brake off of it


Remove wheel and remove brake caliper bracket to remove rotors.

Dec 11, 2010 | 1994 Isuzu Pickup

1 Answer

Front brakes,what tools do i need


To replace rotors and pads, wheel wrench, sockets, hammer, with 4x4, remove wheel,pry pads apart, remove caliper, smack off rotor, and reverse install. 2x4, remove wheel, caliper, hub dust cover, cotter pin, castle nut, and remove rotor and bearings, clean and repack your brgs and replace dust seal, install in new rotor and reverse install. GOOD LUCK, RDJRP

Dec 26, 2009 | 1997 Dodge Dakota

1 Answer

Front breaks are smoking


caliper is sticking or pads are sticking ,proportioning valve with vehicle jacked up and supported and wheel removed inspect pads and rotor for damage excessive wear if good- turn hub/rotor by hand have someone assist u by stepping on brake observe brake caliper stop then release brake piston should release slightly from pad try turn hub again w/out touching brake if stuck in place replace and caliper released replace pads if caliper still clamped remove caliper and inspect for leak or damage compress caliper and try brake again if does if sticks again replace caliper

Oct 13, 2009 | 1988 Dodge Ram 50

1 Answer

Replacing driver side rotor and caliper. How do I remove hub? Does if pop off? Screw off?


Click on my username check my solutions I have explained in detail how to change them. Cheers

Oct 01, 2009 | 1994 Isuzu Pickup

1 Answer

My 1994 Nissan pickup brakes shudder at low speed


Inspect the brake rotors for grooving and score marks and also look to see if there are any heat cracks, if there is grooving or very little brake pad material remaining replace the brake pads and also two new rotors, it is also possible that it is just a frozen or stuck brake caliper, this would be indicated by an uneven rotor one that has more metal or meat on one side that the other also uneven brake pads indicates an uneven brake caliper application

Aug 02, 2009 | 1994 Nissan Pickup

1 Answer

My brake rotor is mounted behind the wheel hub on my 2004 GMC Canyon 4WD pickup. How do I remove the hub so I can get the rotor off? Tks.


Your going to hate this answer. The wheel hub has to come off. This brake system was designed by Isuzu. Don't know what else to say, it's a lousy job.

Jun 20, 2009 | 1994 Hyundai Excel

1 Answer

Debree shields behind rear disc brake rotor rotted out.


Not hard to Replace. you will have to take the Caliper off of the Rotor and then Take the Rotor off, Repack the Bearings! And it is Right There!

Jan 18, 2009 | 2000 GMC New Sierra 1500

1 Answer

I have a 1979 Chevrolet pickup 6 cyl 4 wheel drive Silverado, K ½ ton, that has the 5 lugs sheared off of the right front wheel. I am trying to replace them. How do I remove the front disc rotor to get at...


Remove caliper and nut to axle should come of with a little help of a rubber hammer. Knock bolts out from the front and drive new ones in from the back. You can use a lugnut with the flat side down to help pull them in and a hammer to help. Hope this helps.

Dec 26, 2008 | 1979 Chevrolet C/K 3500

Not finding what you are looking for?
1994 Isuzu Pickup Logo

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...