Question about 1986 Chevrolet S-10 Blazer

1 Answer

Where can I find timing cover for 86 4/4small block v6 2.8L enj.

Posted by on

  • yadayada
    yadayada May 11, 2010

    a 2.6 V6 is not a small block, the small block is a V8, 262 cubic inch through 400 cubic inch.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 229 Answers

Check jegs.com or rock auto.com or your local junk yards.

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel line located in the 2001 oldsmobile alero


Back of enj on drivers side 2 lines , pressure line and return line they are disconnects from rubber to steel

Oct 05, 2012 | Oldsmobile Alero Cars & Trucks

1 Answer

What causes my 2004 chevy trailblazer to overheat? I got the radiator replaced, due to a crack across the top from overheating?..I got the water pump and thermostat replaced too..Also the motor stalls


Well kinda sounds like it has overheated quite a few times, so unfortuanetly it's heads are probably warped and head gskts are blown causing compression from cylinders to enter cooling system which causes high pressure in cooling system which in turn blows coolant out and end result...your enj. probably needs replacing ! Sorry for the Bad news

Feb 13, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

How do I check timing on grand am


The timing (ign) is set by computer. The computer advances it and retards it as need be, by reading all the inputs from the enj. sensors. what enj. and what problem are you having ?

Jan 08, 2012 | 2002 Pontiac Grand Am

1 Answer

How to change the engine belt in a 2003 yukon


I am guessing you have a 5.3 enj.... release the belt tensioner and take old one off and route new back on and let tensior back out

Jan 07, 2012 | GMC Yukon Cars & Trucks

1 Answer

2002 chevrolet 2500hd has no power


How many miles on it and what engine is it, is there a service enj soon light on ? could be your Catalyic Converters are Plugged,this will cause this but usually there will be a code , I guess I need more info on engine if a 6.litre gas, or Duramax

Dec 28, 2011 | 2002 Chevrolet Silverado 2500HD

2 Answers

Oil Is Leaking Out Under The Harminc Balancer On my 92 Jeep Wrangler,4.0 6cyl. I Replaced The Main Seal & Put A New Balancer On & It Still Leaks From The Bottom Of The Balancer


  1. timing cover is leaking oil betwwen cover and block
  2. Disconnect the negative battery cable.
  3. Remove the drive belt(s), fan and fan shroud. If equipped, remove the accessory drive belt pulley.
  4. Remove the vibration damper retaining bolt and washer. Remove the vibration damper using a suitable puller.
  5. Remove the accessory drive brackets attached to the timing cover.
  6. Remove the A/C compressor, if equipped, and alternator bracket from the cylinder head and move to one side.
  7. Remove the oil pan-to-timing case cover bolts and the cover-to-cylinder block bolts.
  8. Remove the timing case cover front seal and gasket from the engine.
  9. Cut off the oil pan side gasket end tabs and oil pan front seal tabs flush with the front face of the cylinder block. Remove the gasket tabs.
  10. Clean the timing case cover, oil pan and cylinder block gasket surfaces.
  11. Remove the crankshaft seal oil seal from the cover by prying it out with a suitable tool.

To install:

  1. Install a new seal in the timing cover using a suitable seal installation tool.
  2. Apply sealer to both sides of the replacement cover gasket and position the gasket on the cylinder block. Cut the end tabs off the replacement oil pan gasket corresponding to those cut off the original gasket. Attach the end tabs to the oil pan with sealer.
  3. Coat the front cover seal end tab recesses generously with sealer and position the seal on the timing cover.
  4. Apply engine oil to the seal-oil pan contact surface, then position the cover on the cylinder block.
  5. Insert timing case cover alignment tool J22248 or equivalent, in the crankshaft opening. Install the cover-to-cylinder block bolts and tighten them to 62 inch lbs. (7 Nm). Install and tighten the oil pan-to-cover bolts to 11 ft. lbs. (13 Nm).
  6. Remove the cover alignment tool and position a replacement oil seal on the tool with the seal lip facing outward. Apply a light coat of sealer to the seal and a light coat of oil to the crankshaft. Install the seal on the timing cover.
  7. Apply a light film of oil to the vibration damper hub seal contact surface. Install the vibration damper using a suitable installation tool.

Do not hammer the damper into place as damage may result to the damper or engine.

  1. Install and tighten the crankshaft vibration damper bolt to 80 ft. lbs. (108 Nm).
  2. If equipped, install the crankshaft pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  3. Install the accessory brackets.
  4. Install the fan and fan shroud.
  5. Install the drive belt(s) and adjust to the proper tension.
  6. Connect the negative battery cable.
  7. Start the engine and check for leaks
  8. .

Jan 18, 2011 | 1992 Jeep Wrangler

1 Answer

Where is the oil sending valve located at?


OIL SENDING UNIT MOST TIME LOCATED CLOSE TO OIL FILTER ON LOWER SIDE OF ENGINE BLOCK.IF OIL PUMP ON FRONT TIMING COVER OF ENGINE LOOK ON FRONT TIMING COVER OR ON THE FRONT SIDES OF THE ENGINE BLOCK.

Nov 27, 2010 | 1987 Dodge Ram 50

1 Answer

My 2001 jeep grand Cherokee will not start don?t know why no codes are coming up put new cam sen, crank sen, coil pack, new ecu, new coolant temp sen, it turns over but will not run has injector pulse and...


Timing Chain, Sprockets, Front Cover and Seal REMOVAL & INSTALLATION 2.5L and 4.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Accessory drive belt
    • Cooling fan and shroud
    • Crankshaft damper
    • Front crankshaft seal
    • Accessory brackets
    • Front cover
    • Oil slinger
  3. Rotate the crankshaft so that the timing marks are aligned. Fig. 1: Timing chain alignment marks — 2.5L and 4.0L engines 7924pg20.gif

  4. Remove the timing chain and sprockets. To install:
  5. For 2.5L engines, turn the timing chain tensioner lever to the unlock (down) position. Pull the tensioner block toward the tensioner lever to compress the spring. Hold the block and turn the tensioner lever to the lock (up) position. Fig. 2: Timing chain tensioner — 2.5L engines 7924pg19.gif

  6. Install the timing chain and sprockets with the timing marks aligned. Tighten the camshaft sprocket bolt to 80 ft. lbs. (108 Nm) for 2.5L engines or to 50 ft. lbs. (68 Nm) for 4.0L engines.
  7. For 2.5L engines, release the timing chain tensioner.
  8. Install or connect the following:
    • Oil slinger
    • New front crankshaft seal to the front cover
    • Front cover, using a new gasket
    • Timing Case Cover Alignment and Seal Installation Tool 6139 in the crankshaft opening to center the front cover Fig. 3: Timing Case Cover Alignment and Seal Installation Tool 6139 — 2.5L and 4.0L engines 7924pg21.gif

  9. Tighten the front cover bolts as follows:
    1. Step 1: Cover-to-block 1⁄4 inch bolts to 60 inch lbs. (7 Nm)
    2. Step 2: Cover-to-block 5⁄16 inch bolts to 16 ft. lbs. (22 Nm)
    3. Step 3: Oil pan-to-cover 1⁄4 inch bolts to 85 inch lbs. (9.5 Nm)
    4. Step 4: Oil pan-to-cover 5⁄16 inch bolts to 11 ft. lbs. (15 Nm)
  10. Install or connect the following:
    • Accessory brackets
    • Crankshaft damper. Tighten the bolt to 80 ft. lbs. (108 Nm).
    • Cooling fan and shroud
    • Accessory drive belt
    • Negative battery cable
  11. Start the engine and check for leaks.

Jul 30, 2010 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...