Question about 2006 Jeep Wrangler

4 Answers

2006 Jeep Wrangler won't start

Replaced the battery. Replaced the starter. Replaced ignition switch. Turn the key, lights/radio, etc come on, but Jeep wont' start. Hear a click behind right dashboard.

Posted by on

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

First, make sure you can turn the engine by hand. If you can't then the starter can't turn it either. Have someone else turn the key and look for the source of the click...may be a relay. Go over the starting circuit with a volt meter. Check for power at the starter main terminal and then with the key turned to "start" check for power at the trigger terminal on the starter. Check battery voltage and check relay operation.
You have a neutral safety switch on the transmission if its an automatic and a clutch switch if it's a stick. Check them as well. Make sure battery grounding on fender and block are also clean and secure.

Posted on Oct 02, 2009

Testimonial: "Will try! Thanks!"

  • mp0409 Sep 19, 2010

    how did you fix the issue?

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Had the same problem. Turn key, but nothing happens. Turns out the 30amp fuse under bonnet ( hood) had blown. Started no problems when push started. Replaced fuse, and was o.k for a while, but blew fuse again a few weeks later. Once again replaced the fuse, and all starts o.k. I suspect a faulty solenoid/ worn starter motor brushes, which I will check next service.

Posted on Jan 09, 2014

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Jeep Master
  • 552 Answers

Check to see if you have spark and fuel pressure

Posted on Nov 10, 2011

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same issue -- 2006 Wrangler. Engine light comes on when I turn the key without starting the engine. Radio, lights, AC all work. Engine light blinks 9 times. Try to start and hear nothing...won't start. Turn key off and back on a few times and it finally starts. Took to autozone to run a check and comes out clean....no issues. Said it maybe an EMF or ECS or something like that. I don't want to spend $$$$$ to take it to Jeep.

Posted on Jun 14, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 jeep wrangler 4.0,won,t start,dash lites won,t go on.replaced starter relay.still won,t turn over.


Try checking the battery and battery leads. Sounds as though you have a bad battery. Also check your fuses under the hood and dash.

Jun 03, 2011 | 1995 Jeep Wrangler

1 Answer

JUST PAID OVER $600 A MONTH AGO - NEW STARTER, BATTERY, IGNITION SWITCH, AND TUNE-UP - LEFT HOME, STOPPED AT MOM'S, GOT BACK IN 1998 JEEP WRANGLER - NOTHING! NO ATTEMPT AT STARTER, NO CLICKS, NO NOISE -...


Sounds like a faulty / intermittent Earth connection. Check all the battery and earth leads where they connect to the Battery, Engine, Starter Motor and Body. If possible disconnect, clean thoroughly by removing any corrosion or paint that could cause a poor connection, and reconnect making sure all are tight.

Sep 28, 2010 | 1998 Jeep Wrangler

1 Answer

1989 Jeep Wrangler no power when key is in on position


Honestly, it sounds like a bad ignition coil. When they get corroded inside they will draw power on a scale much higher than anything else on the vehicle. It is a coil and it's job is to take a little power and make a lot of it. If it's only when the key is in the "run" position, that is likely the case. The only real difference between the two positions is that in the run position there is power being delivered to the ignition system. Good luck.

May 05, 2010 | 1989 Jeep Wrangler

2 Answers

2004 jeep wrangler unlimited wont start ,4.0l auto , new starter and battery , when turn the key lights come on fuel pump lights in dash.


Nuetral safty switch, Starter solenoid.
Do you have antitheft?
The ground for the starter relay may be computer controlled. Lee

Oct 04, 2009 | 2007 Jeep Wrangler Unlimited Rubicon 2...

3 Answers

2006 Jeep Commander Intermittent Starting Problems


Common problem in snow country where salt water can corrode starter parking gate wire connection at started tab. Just cleanthe connector and tab, coat in dielectric grease, problem solved in 15 minutes!

Sep 12, 2009 | 2006 Jeep Commander

4 Answers

My 91 jeep won't start...


The Starter relay is bad.

May 05, 2009 | 1991 Jeep Wrangler

Not finding what you are looking for?
2006 Jeep Wrangler Logo

2,592 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...