Question about 1999 Chevrolet Blazer

1 Answer

How to replace front wheel bearing assembly - 1999 Chevrolet Blazer

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 226 Answers

Remove the; brake caliper, brake rotor. center axle nut. There are three bolts from the inside that screw into the bearing hub assy.
None of this is as easy as it sounds. You need a special socket for the bolts. Make you use a jackstand please. Lee

Posted on Oct 01, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: how do I replace a front wheel bearing assembly on

Remove tire, brake caliper and rotor (before doing this use a solid breaker bar and a long steel pipe to remove center nut on axle) It is tight (about 170lbs) Once everything is off, put the nut on the axle backweards and make it even with end. give it a tap with a hammer to break it free from the bearing splines. There are three 12point bolts on the backside of the steering knuckle. back them out a bit and use a chisel between the bearing and knuckle to get it free. Use lots of wd40 or other solvent. If you need to, hammer a bit on three bolts.But not so much you can't get a wrench on them. as bearing becomes free, remove bolts and finish. Assemble in oposite order (but no hammering) when tightening axle nut use # I gave you and do not loosen to get cotter pin through hole...tighten further.

Posted on May 16, 2009

  • 1 Answer

SOURCE: hub assembly and wheel bearings problem

I just had my wifes replaced.[4x4 blazer S-10] Chev want 300.00 for each, I went on line and got the parts cheap and a friend from chev put them on in his garage. I think the whole thing cost me 200.00

Posted on Jan 11, 2009

michigan man
  • 3533 Answers

SOURCE: How to replace front wheel bearings on a 2001 Ford Escape 4X4

try "autozone.com" or your local library for diagrams and step by step instructions

Posted on Mar 08, 2009

motor1258
  • 6674 Answers

SOURCE: wheel bearing assembly 2004 dodge ram 1500

Hub & bearing should be one assy, is that what your looking at?
3 bolts behind hub, to remove, done?

Posted on Apr 05, 2009

ajarema
  • 404 Answers

SOURCE: How do I replace the front wheel bearing on a

First you need to untight the half shaft nut, than detach all ball joints (4 of them), than you remove the hub from the half shaft, you will actually need to have a press (about 12ton min) to press the bearing out and press new one in, don't try to hammer it as you can possibly damage the hub and than you will need to buy new one (or second hand). After getting it pressed in you basically need to put it back and reverse the whole process of dismantling.

Posted on Apr 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2wd.how to replace front wheel bearing assembly


There are a number of videos...
For RWD front hubs. (F250 will just have larger bolts.)

How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150
For 4x4 front hubs.

Ford Super Duty hub bearing replacement Driver side

May 06, 2016 | 2005 Ford F 250 Super Duty

1 Answer

2007 toyota tacoma replace front wheel bearing prerunner


The other guys have never taken the wheel bearings out of a 2007 Tacoma! Remove the tire (duh)
Remove the 12mm bolt holding the brake line securing bracket
Un-clip the air sensor hose clip
Remove the two 17mm bolts holding the brake assembly on the back side
Remove the rotor from the wheel "spindle"- slides right off.
Unscrew the four metric bolts (maybe 17mm) holding the wheel housing to its mount (they cannot be removed from the assembly yet, see below).
That's right there is no normal wheel spindle with a big nut on the end of a threaded shaft in the middle!
The wheel mounting plate (with the 6 studs) is pressed into the bearing housing.
Get a replacement bearing assembly and take it and your old unit to a machine shop (unless you have a good press).
An easy job, just expensive- $140 for the bearing assembly.

Mar 27, 2012 | 2007 Toyota Tacoma

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

Replace front hub assembly.


Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
Remove tire/wheel
Remove brake caliper assembly, do not remove brake line.
Remove caliper bracket.
Remove brake rotor.
Unplug ABS sensor.
Remove the large axle nut.
Press axle out of bearing (may need special tool)
Remove the 3 bearing bolts and remove bearing.

May 19, 2010 | 2003 Chevrolet Impala

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

3 Answers

Replace front wheel bearing is it hard to do on 2002 alero


its actually pretty easy if you have the basic tools needed and a little mechanical knowledge, because i dont think you can buy just the bearing at a auto parts store. they sell you the whole hub assembly which is great for the DIYer.

lift the car off the ground and block it from rolling and place a jack stand under it so it cant fall on anyone.


Wheel Bearings printpage_icon.gif

Removal & Installation

These vehicles are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are non-serviceable. If the assembly is damaged, the complete unit must be replaced.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    WARNING DO NOT allow the caliper to hang unsupported from the brake hose.


    Front wheel Halfshaft nut and washer Caliper from the steering knuckle and support it aside


    Brake rotor Anti-lock Brake System (ABS) connector, if equipped 3 hub/bearing assembly bolts Halfshaft from the hub/bearing assembly Hub/bearing assembly

    0900c1528023b277.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the front hub/bearing assembly


To install:
Install or connect the following:

Hub/bearing assembly onto the halfshaft, making sure the splines engage smoothly Hub/bearing assembly to the steering knuckle. Torque the bolts to 70 ft. lbs. (95 Nm). Anti-lock Brake System (ABS) connector, if equipped Brake rotor Caliper onto the steering knuckle. Torque the bolts to 38 ft. lbs. (51 Nm). Halfshaft nut. Torque the hub nut to 284 ft. lbs. (385 Nm) on nuts colored black, or 173 ft. lbs. (235 Nm) on gray colored nuts. Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Jul 27, 2009 | 2004 Oldsmobile Alero

1 Answer

Wheel bearing replacement left front wheel Hello Everyone, I may need to replace the wheel bearing on my right front wheel of my Corolla wagon. How can I know for sure? And how can I find out how to do...


Diagnosing the bearings can be tricky depending on severity of wear. Typically - drone noise at highway speeds, squeeling, clicking or grinding noises at low speeds that reduce during braking, or pull off the wheel and brake assembly and check the bearing for slack or smoothness of rotation by hand. While doing this, check the brake assembly thoroughly - generally a more likely culprit of wheel noise.

Wheel bearing replacement is not for the novice backyard mech. - you will need pullers, press, etc. If you can get a rebuilt assembly - much easier.

Apr 23, 2009 | 1996 Toyota Corolla

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...