Question about 1999 Chevrolet Blazer

1 Answer

Don't know how to remove retaining clips for rear axles on a1999 Bravada

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 75,814 Answers

Pull the rear cover off the diff, then remove the center block from the gear carrier, there is a single pin in the side that lets the block and cross pin come out, the push the axles in and remove the "C" clips retainers.

Posted on Oct 01, 2009

Testimonial: "thanks for the help. I wasn't sure houw much would fall out if I remove the pin."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change rear axle seal on 1991 dodge Dakota 4×4?


Remove the wheel and tire.

Remove the drum.

Drain the rear and remove the cover.

Locate the 8mm bolt locking in the center pin and remove it.

Slide the pin out 1/2 way. DO NOT SPIN EITHER AXLE WHILE THE PIN IS OUT.

Push the axle in from the outside. You will hear the "c" clip fall in the rear. Put the center pin back in the rear and thread the bolt a couple turns.

Slide the axle out.

Remove the outer seal and install the new one.

Reverse the procedure REMEMBERING to put the "C" clip back in.

(Slide the center pin 1/2 way out. Install the axle FULLY. install the "C" clip and pull the axle from the outside to insure the clip is in. DO NOT SPIN THE AXLE until the center pin is reinstalled and the retaining bolt is in.)

May 31, 2015 | Dodge Cars & Trucks

1 Answer

How do you change the rear axle seal


This is a c clip axle remove diff cover rotate carrier to gain access to drive pin bolt on passenger side of carrier. remove bolt 5/16 head pin will slide out . NOW DO NOT ROTATE ANYTHING. on the side the axle seal is bad tire should be off brake drum off (disc remove caliper and mount) push in on axle c clip should fall out then slide axle out. remove seal with a seal puller and install new one.

May 05, 2014 | 2001 Oldsmobile Bravada

1 Answer

What holds axle shaft in


Rear differential axles are retained by a "c" clip. You can remove it by taking out the retaining bolt for the spider gear cross shaft, sliding the shaft out of the carrier then pushing the axle in. The clip (actually just a "C" is easily removed and the axle then just pulls out.) careful not to turn the carrier unless you make an effort to keep the spiders from falling out.

Nov 25, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Replacing a rear wheel bearing 1996 gmc sonoma 5 speed what all is involved does the axle have to come out or can you just take wheel and brakes drum off etc.


To remove the rear axle to replace a bearing you have to remove the rear differential cover and remove the small retaining bolt holds the spider gear shaft in place and then slide this shaft out far enough to remove the "C" shaped axle shaft retaining clip. Once this clip is off then the axle can be slid out and the bearing & seal replaced. Make sure that none of the spider gears or thrust washers behind them get out of place and you should use a new retaining bolt when reassembling the differential components as they come [or should come this way] with thread locker to prevent them from coming loose.

Jun 22, 2010 | 1996 GMC Sonoma

1 Answer

How do you remove c-clips on axle of 95 ford rear end?


If you have already removed the outer axle bearing cover in the rear hub, try popping the axle out as some of them have a compression clip holding it in place in the differential. If it doesn't pop loose, you wil have to remove the differential cover and push the axle inward enough to access the retaining clip to remove it. It should slide out fairly easile once the axle is pushed in far enough to clear the retainer clip lock collar.

Aug 17, 2009 | 1995 Ford F150 Styleside Regular Cab

3 Answers

REAR AXLE SEAL LEAKING ONTO BRAKE SHOES NEED INSTRUCTIONS ON HOW TO FIX


Jack up vehicle and support on stands. Remove wheels. Remove differential cover . Locate and remove lock pin that holds cross shaft in. Slide cross shaft out. Push axle inward to release axle c clip. Remove axle and pry out old seal. Install new seal with proper tool.Add some lube to the seal lip to aid axle intallation. Revese removal procedure. This is for a "c" type axle.
Another type has 4 nuts attaching a retainer plate to the backing plate behind the axle flange. In this case the 4 nuts are removed and the axle will come out. This may require a little effort. I think that you have a "c" type axle in your vehicle. Hope this helps. Moe

Apr 28, 2009 | Jeep Cherokee Cars & Trucks

1 Answer

Leaking right rear axle seal on 1986 F-150


You must pull the diff cover off, then remove the center pin and spider gears, then remove the C clip that holds the axle in the carrier assembly.
Please rate me.

Nov 22, 2008 | 1986 Ford F150 SuperCab

1 Answer

98 Ford F-150 2WD rear axle removel


The Ford is similar to the Chevy. Same procedures apply. Same retaining bolt in center section needs to be removed to allow cross shaft to come out. Same technique in removing spider gears. Same "C-clip" retainers on axle ends. you shouldn't have any issues.

Oct 19, 2008 | 1998 Ford F150 Regular Cab

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...