Question about Mercury Sable

1 Answer

How do i find the starter on a 1995 mercury sable???

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 347 Answers

Jack it up should be on the driverside of the front near the ex pipe

Posted on Oct 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My key won't turn to start my car... It's a 92 Sable Mercury.


Try a lubricant.

Mercury Sable key ? Mile High Locksmith ™

www.denver-locksmith.net/2013/12/mercury-sable-key-replacement/
Dec 23, 2013 - Mercury Sable keys have changed over the years. ... 1991, 1992, 1993, 1994, or 1995, then your car requires two keys. ... If your Mercury Sable was made in the year 1997, then some of the cars will have a transponder key, and some won't. ...Insert the new key into your ignition switch and turn it to the on .

Sep 08, 2015 | Mercury Sable Cars & Trucks

2 Answers

Where is the ignition control module located on a 1995 mercury sable 3.0 v6


For 1995 Mercury Sable 3.0L EFI 6cyl the Control Module-Ignition is located: Under hood, center, upper engine area, mounted on side of distributor.

Hope helps (remember rated this).

Aug 11, 2010 | 1995 Mercury Sable

1 Answer

1995 Sable when ignition switch turned off, engine still runs and everything keeps working. ignition switch was changed; still has problem


You said you changed the ignition switch. You changed the switch or the ignition lock cylinder? I've seen cars also do this after a remote starter has been installed but you said you nothing like that on your car.

Jul 13, 2010 | 1995 Mercury Sable

1 Answer

No spark from coil


I had the same problem with my 97 sable it turned out to be the ecm module.

Sep 06, 2009 | 1995 Mercury Sable

1 Answer

I have a 95 mec sable wgn 3.8 and it wont start turn key and nothing happens no sound and the lights dont dim like if bat is weak also radio and dash clock shut off but when back on stilcorrect settings im...


try to check if the starter relay clicking while you start.If no maybe bad connection from ignition key. If the relay clicking maybe the connection to starter or the starter itself is damaged. try to direct the sol. of starter to batt. positive if it kick your starter is good.

Jun 08, 2009 | 1995 Mercury Sable

1 Answer

Starter solenoid - how to replace


Section 03-06: Starting System 1996 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Starter Motor Removal
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING STARTER MOTOR (11002) OR PERFORMING ANY MAINTENANCE IN THE AREA OF THE STARTER MOTOR, NOTE THAT THE HEAVY GAUGE INPUT LEAD CONNECTED TO THE STARTER SOLENOID (11390) IS HOT AT ALL TIMES. MAKE SURE THE PROTECTIVE CAP IS INSTALLED OVER THE TERMINAL AND IS REPLACED AFTER SERVICE.
    Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Raise the vehicle on a hoist. Refer to Section 00-02 .
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When disconnecting hardshell connector of the engine control sensor wiring (12A581) at S-terminal, grasp the plastic shell and pull off. Do not pull on wire. Be careful to pull straight off to prevent damage to the connector and S-terminal. If any part of the connection is damaged, replace the damaged components.
    Disconnect engine control sensor wiring and starter battery cable from starter solenoid.
  1. Remove upper and lower retaining bolts.
  1. Remove starter motor.

Apr 09, 2009 | 1995 Mercury Sable

1 Answer

I need to change my starter on a 1991 mercury sable


Starter are one of the easier mechanical engine parts to change.

1) DISCONNECT THE BATTERY.
2) Disconnect the electrical cable running to the solenoid on the starter.
3) Remove the two bolts holding the starter in place.
4) Pull the starter out.

To install another starter, do the above steps in reverse order in reverse.

Apr 04, 2009 | 1991 Mercury Sable

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

fordexpert

Level 3 Expert

5623 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...