Question about Hyundai Motor 2004 Accent

2 Answers

Getz 1300 hAas new cam belt fitted but now there

Getz 1300 has 50000service and then on seperate occasion a new cam belt fitted but now there is a rasping whining noise as revs die away. Mechanic suggests it might be tight belt but doesnt it have a tensioner so shouldnt be that. Any ideas?

I have entered Accent below as the getz doesnt feature

Posted by on

  • Anonymous Mar 12, 2014

    Rasping noise from engine/transmission on accelerating. Stops on lifting off gas or cruising on level ground.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

It is a tight belt, it doesnt need a tensioner the technition put on tooo tight

Posted on Oct 03, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

The tensioner is NOT spring loaded - it's adjusted by the technician who installed it. Take it back and tell them to FIX IT!

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to align the timming marks of the cam-belt on my 1,4 Getz ?


Sorry but you have internal problems, when your belt broke it caused contact between the valves and pistons. The cylinder head will need to be removed and inspected what damage has been done.

Aug 03, 2014 | 2007 Hyundai Getz 1.4

1 Answer

Hyundai getz starting problem


run the fault codes and find exactly which sensor should have been fitted

Mar 08, 2014 | Cars & Trucks

1 Answer

Replacing a daihatsu terios timing belt


the procedure of aligning all the timing marks before removing the belt will be the same . The necessity of not moving crank and cams without the belt being connected is still relevant. How ever there are some differences as to tensioning the belt and timing balance shafts . The biggest killer of rubber belts is oil so the oil seals (Cams shaft/ crank shaft should be also replaced and hydraulic tensioner if you have one). Idler pulleys do as much work as the belt so replacing them to replace the bearings is also a good move. . To come up to speed as to the differences a workshop manual for your vehicle is strongly recommended.

Jan 26, 2014 | Cars & Trucks

1 Answer

Torque settings on hyundai getz 1.6 Top and cam


The info is said to be available here, if the link still works. You may have to register yourself first.

http://www.hyundai-forums.com/attachments/getz-forum/57970d1353332110-help-hyundai-getz-1-6-torque-settings-getz-1.5-1.6-specs-torque-settings.pdf

Dec 20, 2013 | Cars & Trucks

1 Answer

Noise after fitting cam belt


When you refitted the belt, was there a spacer ring refitted correctly?
Also, check for any sprocket key was fitted correctly and that the crankshaft pulley bolt was refitted correctly and was tightened properly.
There's also the slight possibility that the plastic casings weren't fitted flush and are being scraped by the pulleys or belt.

Nov 18, 2012 | 2005 Fiat Doblo 1.9

1 Answer

S60. 2.4T removing and replacing timing belt


remove auxilary belt remove one bolt from timing belt cover remove cover turn engine to tdc using socket on crank nut check cam pulleys lined mark with white paint or tipex remove 4 bolts on crank pulley then centre pulley nut use impact gun prise of pulley check all marks still lined up buy or borrow universal cam sproket lock tool this is important to stop cams moving when belt of release tensioer remove belt chek water pump for leaks and wear fit new tensioner then new belt keep tight on non tension side feed over sprokets tension belt to align pointer on tensioner turn engin 2 times re check timing marks fit all parts removed

Nov 23, 2009 | 2001 Volvo S60

Not finding what you are looking for?
Hyundai Motor 2004 Accent Logo

Related Topics:

376 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...