Question about 2005 Hyundai Accent

1 Answer

REPLACING FRONT BRAKE PADS ON A GETZ 55 PLATE

Posted by on

  • silver top May 11, 2010

    hi from uk could you please be specific as to your post ? are you asking when to replace ? or how to D I Y replacing front pads ? if the latter then this is simple d i y job if you are mechanically confident ? my wifes car is a getz and have taught her how using my tools here in uk new pads cost approx £15 trade however if you visit E BAY you can get discs and pads as a set and very reasonable

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What cause front brake lock up in hundai getz 1.3 2005 model


this will be from a faulty master cylinder wit a blocked compensation port
pads are dragging and building up heat which is expanding the brake fluid and as it cannot get back to the reservoir it puts the pads on harder
it is also evident if you apply the brakes and the car takes extra power top move off
I suggest that you take it to an accredited brake specialist and get a proper diagnosis and a quote for a new master cyl

Oct 02, 2015 | 2005 Hyundai Getz 1.3

1 Answer

Need instructions to remove the front rotor on F250 Four wheel drive truck - 2001 year


  1. Raise and support the vehicle; Remove the wheel and tire assembly;
  2. After removing the tire, remove the brake pads;
  3. Remove the disc brake caliper by removing the two disc brake caliper pin bolts. Lift the disc brake caliper from the disc brake caliper anchor plate (2B292). If necessary, remove the V-springs.
  4. Remove the pads. Remove the front disc brake caliper anchor plate stainless steel rail clips.
  5. Remove the rotor.
  6. Note: Perform this step for DRW vehicles. Remove the eight hub extender nuts, the hub plate and the rotor. Remove the eight hub plate nuts. Remove the hub plate. Remove the rotor.

Mar 02, 2011 | 2001 Ford F250 Super Duty Super Cab

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

2 Answers

How to replace the front brake pads on a hyundai getz, 2008 1.4


Instead of explaining in words, here you find the right link to understand the disc barking system & how to relace the worn out pads.The link refers elantra, but the basic remains same for the GETZ.

http://www.cockeyed.com/lessons/brakeshoes/brakeshoes01.shtml

Jun 05, 2010 | 2009 Hyundai Genesis

3 Answers

Brake pad replacement. My brakes are making a squeeking sound as I drive. Sounds like rotor or brake pad problem.


Here is Video of How to replace front brake pads and rotors, and rear brake pads on toyota camry solara 2006

Mar 16, 2010 | 1991 Toyota Camry

1 Answer

I am replacing the rear pads and cannot get the caliper to compress using a c-clamp. Is there something special I need to do or know on my montego 05 car to get the caliper to compress? Sincerely Desperate...


One, take your brake fluid reservoir cap off.
Two, use a thin piece of wood to help you compress the piston on the caliper....do it slow. This way, you don't create a lot of pressure to the reservoir and it won't overflow.
Three, these are the steps to removing and replacing the pads for the rear. It does mention a special tool....but you can use a c-clamp for the same purpose:

Rear To Remove:
  1. Check the brake fluid level in the brake master cylinder reservoir.
  2. If required, remove the fluid until the brake master cylinder reservoir is half full. CAUTION
    Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever.
  3. Remove the disc brake caliper. Support the caliper with mechanic's wire. CAUTION
    When the brake pads are separated from the brake caliper, new brake pads must be installed. The brake pads are one-time use only.
  4. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed.
  5. Inspect the brake caliper anchor plate assembly.
  6. Check the guide pins and boots for binding or damage.
  7. Install a new brake caliper anchor plate if it is worn or damaged.
To Install:
NOTE: The left caliper piston turns clockwise and the right caliper piston turns counterclockwise.
  1. Using the special tool, turn and compress the brake caliper piston into the cylinder.
  2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. CAUTION
    Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface. Do not install contaminated pads.
    NOTE: Install all the new hardware supplied with brake pad kit.
  3. Install the new spring clips and brake pads.
  4. Position the brake caliper and install the 2 bolts. Tighten caliper bolts to 23 ft-lbs (31 Nm).
  5. If necessary, fill the brake master cylinder reservoir with clean brake fluid.
  6. With the engine running, apply pressure on the brake pedal to seat the brake pads.
  7. Test the brakes for normal operation.

May 17, 2009 | 2005 Mercury Montego

1 Answer

I replaced front brake pads on my 05 plate volvo v70 sport d5


hey log on to www.2carpros.com and click how to change brake pads it explains everything there.

Apr 02, 2009 | 2004 Volvo XC90

2 Answers

Front calipers


Good morning,
I have several questions that can lead you to a solution.
1) How many miles on the front brake pads sense they have been replaced?
2) How deeply grooved are the front brake rotors?
3) does the front brakes make a scratching or a grinding sound when the brakes are applied?

This is where I'm heading with these questions:

The front brake pads are a biscuit of break friction material applied to a steel plate.
As the braking material wears off the rotor may also wear with grooves and in the case of replacing pads without turning the rotor can present a ledge on the rotor that the plate of the brake pad can come it contact with and restrict the friction material from coming in contact with the rotor and be an effective breaking force.

Also if the pads have been replaced and the piston has become cocked in the caliper it will be jammed in the piston bore and not be free to extend and exert a pinching force on the rotor.

I suspect that if the fluid is not restricted from reaching the caliper there is a mechanical restriction in the system. Not much else to consider but those two things.

Glad to be of assistance - please rate the solution - I can learn from you. Thank you

Oct 27, 2008 | 1997 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...