Question about 1995 Dodge Ram

1 Answer

Have a leak by the oil pressure sensor I can see the piece it is melted with a red clip and says vac on it. what is this called

Posted by on

  • jbalsavage Oct 02, 2009

    It was the egr solenoid. thanks anyway guys

×

Ad

1 Answer

Sounds like your looking at the Air Conditioning Port, not oil press. More detail as to what help you need!!

Posted on Oct 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car keeps dying has black smoke smells like rotten eggs


Cat converter is major damage. The piece is made out of a honeycomb of metal and it melted down and is blocked causing call to stall

Dec 28, 2015 | 2005 Chevrolet Chevrolet Impala LS

1 Answer

How does someone install manual oil pressure gauge on 2006 chevy 2500 with 6.0L Vortex


where the oil pressure sender unit is on the block install a "t" fitting . Place the electrical unit in one side and a brass fitting in the other . Run the copper line from the gauge through the firewall to the "T" piece and connect up (if you are using a plastic tube the do not waste your time as the plastic fails -cracks ,slips. or melts causing engine failure) Position the gauge and connect the copper line to the gauge . run engine and check for oil leaks.

Nov 30, 2013 | 2006 Chevrolet Silverado 2500HD 2WD

2 Answers

Cause of rough idle/1990 buick riviera/3.8 l


I agree with the possible bad fuel theory. You would need to figure out if the miss is a fuel problem or ignition problem to proceed.
I would pull the plugs and look at them, also check for vac leaks.
Is the check engine light on when the engine is running ? If so check for trouble codes.

Jul 26, 2012 | 1990 Buick Riviera

1 Answer

Engine light stays on code PO 171 45 lb gas pressure


Not sure what the 45lb gas pressure is for. Fuel pressure ??
In most cases the code is for bank one O2 sensor out of range. There are about a dozen possible causes including a vac leak. The sensor is reading too much air in the exhaust based on the other engine readings.
Things like a stuck PVC valve, leaking vac hose, leaking exhaust, leaking intake manifold, or even a failed O2 sensor.

Jun 25, 2012 | 1997 Buick Park Avenue

1 Answer

Oil pressure light stays on .engine is running good .why is the light on?


Check the oil pressure sensor and the wiring to it.

Oil Pressure Sensor Removal & Installation 3.4L & 3.5L Engine To Remove:
  1. Disconnect the battery ground cable.
  2. Raise and safely support the vehicle.
  3. Disconnect the electrical connector from the oil pressure sensor. chev_vent_op-sen.gif

  4. Remove the oil pressure sensor from the engine.
To Install:
  1. Install the oil pressure sensor on the engine. Tighten 12 ft-lb (16 Nm).
  2. Connect the oil pressure sensor electrical connector.
  3. Lower the vehicle.
  4. Connect the battery ground cable.
  5. Start the engine and check for leaks.
3.6L Engine To Remove:
  1. Disconnect the oil pressure sensor electrical connector. Oil pressure sensor 3.6L gm-04-36-2519.gif

  2. Remove the oil pressure sensor.
To Install:
  1. Install the oil pressure sensor. Tighten 15 ft-lb (20 Nm).
  2. Connect the oil pressure sensor electrical connector.
  3. Check for leaks.
prev.gif next.gif

Aug 07, 2010 | 2003 Buick Rendezvous

1 Answer

P1171 no mil no other codes


Check compression, maybe worn valves or valve guides. I believe compression should read over 90psi. Check ignition system for obviouse deteriation or carbon/oil buildup on spark plugs, take note which plug has biuldup if any.

Also make sure it doesn't loose oil or coolant, indicating a possible intake or head gasket.

Good luck.

Mar 30, 2010 | 1996 Saab 900

1 Answer

Ruff idle was wondring if problem could be/ o2 sensor/trottle control / I disconnected the MAF sensor and noticed that it is a little better but still ruff idle . From time to time . Example when i come...


The basics for a rough idle, check for a leak of some kind, fuel--egr--vacuum.
Use a gage and check proper fuel pressure. Also, see if pressure will hold for a bit with everything off. If it drops like a rock, you have a fuel pressure leak. Check the vac line on fuel pressure regulator, where applicable, if it has gas in it, the regulator is faulty.
Smell of your crankcase oil dipstick, does it smell like gas? If so, either you don't change oil and filter very often or there is a fuel leak getting into your oil.
Any applicable trouble codes?

May 14, 2017 | 1995 Lincoln Town Car

1 Answer

Oil indicator on BMW 318 2001


Hi , is the colour of the warning light red or yellow, red would be for oil pressure , yellow would be for oil level , but you may find that the oil level sensor has become faulty, reagrds mark

Jun 29, 2009 | 2000 BMW 3 Series

1 Answer

Repeat bad o2 sensors, oil burning, engine cuts in clutch


You may have a blown heads. Try by replacing the oil pressure sensor located in the rear of the engine. Second clean the throttle body by taking off the hoses. Get the cleaner from the auto parts store. Clean throttle body, air intakes, air filter, new oil filter, and have your feul injectors services. Did you check under the car for oil leaks? Try placing a white sheet under the car to see if you have a bad oil spill. Make sure all harness wires are not shorting out. Alot of wires are placed close to heat sources and could melt them. Yoyu just have to replace the melted section and reroute the wiring........runjoe

Jan 23, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...