Question about 2005 Cadillac Deville

1 Answer

I need to reprogram a keyless remote for my 05 caldillac

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Cadillac Master
  • 3,854 Answers

This info is for a 2005, i think you need to follow method #2

There are 4 methods for programming key fobs. Up to 4 key fobs may be programmed to the remote control door lock receiver (RCDLR). Each programmed key fob is given a position of #1-#4 in the RCDLR memory.

Method 1 - Key Fob Quick Learn

This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
Place the replacement key fob in the console fob pocket with the buttons facing forward.
A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED.
If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 2 - Key Fob Slot Programming

This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.

Important: This procedure is not available when the maximum number of fobs (4) have been programmed. If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance.


The vehicle must be OFF.
Place a known key fob within the interior of the vehicle.
Install a scan tool.
Use the scan tool, to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 3 - Key Fob Auto Learn

This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.


The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Method 4 - Service Programming System Fob Programming

This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the fobs can be programmed similar to Method 2 using slot programming. A scan tool, Techline Terminal, and a replacement key fob are required to perform this procedure.

Place the vehicle in the Vehicle On, Engine Off mode.
Connect a scan tool to the vehicle.
Insure that all power consuming devices are turned OFF on the vehicle.
With a scan tool, select Request Info under Service Programming System and follow the scan tool on-screen instructions.
Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software.
Turn the vehicle OFF.
On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions. Ensure the correct programming procedure is selected based on component being replaced or programmed. See Important above.
Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle.
With a scan tool, select Program ECU under Service Programming System.
At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
When the 10 minute relearn procedure has completed, use the scan tool to access the following:
• Vehicle Control Systems

• Computer/Integrating Systems

• Module Replacement/Setup

• RCDLR

• Program Key Fobs

Select Fob X (X = 1, 2, 3, or 4) on the scan tool. This will be the slot you wish to program to.
Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion. The previously known fob is now erased.
If programming additional key fobs, repeat steps 12-13, or press the OFF/ACC portion of the ignition switch to exit programming.
Remove the scan tool.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.


Good luck Molson

Posted on Dec 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bought a used keyless entry remote key fob, how do I reprogram it to a 2008 suzuki sx4?


the operators guide covers this.
lost that? (in the glove box is was)

Jul 02, 2014 | 2008 Suzuki SX4

1 Answer

Saab experts


May be keyfob needs reprogramming.

Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.

If the remote s faulty then key fob will not get programmed.

Insert the key in ignition. Turn the key to on position, and cycle the key three times off-on-off-on-off-on. Then with the key fob remote select your remote and then try to operate the vehicle with remote.

These are just the basic procedure, but sometimes it will not help.

On that case dealer is the only option.


---------

There are few much related troubleshooting links mentioned below for remote key fob reprogramming. I suggest you to go through the list and click the link below to go through its details and procedure: -------




Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------



2009 Toyota Highlander: Smart Key Not getting Detected?

http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html


----------

2007 Toyota Prius: Reprogram Remote Keyfob?

http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html

-----------

Pin that holds the flick key part to the key fob?

http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html

-------------


2006 Toyota Hilux: Programming New Key?

http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html

----------

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html

----------

Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

----------

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html

-----------

Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------

Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------

Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------

Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------

KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------

Mitsubishi Car Key Not getting detected after replacing ECM

http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html

-----------

Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------

2000 Jeep Cherokee Limited: KeyFob Remote Not Working?

http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html

-----------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

-----------

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

--------------


These details will help.

Thanks.

Dec 04, 2012 | Cars & Trucks

1 Answer

Peugeot 206 key fob


Try with brand new key fob battery and see.If that helps.
Otherwise May be keyfob needs to be reprogrammed.

KEYFOB PROGRAMMING


Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.

If the remote s faulty then key fob will not get programmed.

Insert the key in ignition. Turn the key to on position, and cycle the key three times off-on-off-on-off-on. Then with the key fob remote select your remote and then try to operate the vehicle with remote.

These are just the basic procedure, but sometimes it will not help.

On that case dealer is the only option.


---------

There are few much related troubleshooting links mentioned below for remote key fob reprogramming. I suggest you to go through the list and click the link below to go through its details and procedure: -------

2009 Toyota Highlander: Smart Key Not getting Detected?

http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html


----------

2007 Toyota Prius: Reprogram Remote Keyfob?

http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html

-----------

Pin that holds the flick key part to the key fob?

http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html

-------------


2006 Toyota Hilux: Programming New Key?

http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html

----------

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html

----------

Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

----------

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html

-----------

Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------

Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------

Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------

Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------

KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------

Mitsubishi Car Key Not getting detected after replacing ECM

http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html

-----------

Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------

2000 Jeep Cherokee Limited: KeyFob Remote Not Working?

http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html

-----------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

-----------

Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

--------------


These details will help.

Thanks.

Nov 28, 2012 | Peugeot Cars & Trucks

2 Answers

How program the key remot


Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.If the remote s faulty then keyfob will not get programmed.Insert the key in ignition.Turn the key to on position,and cycle the key three times off-on-off-on-off-on.Then with the keyfob remote select your remote and then try to operate the vehicle with remote.These is just the basic procedure,but sometimes it will not help.
On that case dealer is the only option.
---------There are few very relted troubleshooting links mentioned below for remote key fob reprogramming.I suggest you to go through the list and click the link below to go through its details and procedure:-------
2009 Toyota Highlander: Smart Key Not getting Detected? http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html
----------2007 Toyota Prius: Reprogram Remote Keyfob? http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html
----------- Pin that holds the flick key part to the key fob? http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html
-------------
2006 Toyota Hilux: Programming New Key? http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html
----------Where is Key chip memory located on 2004 ford Freestar? http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html
----------Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html
----------After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure? http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html
-----------Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------
Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------
Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------
Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------
KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------
Mitsubishi Car Key Not getting detected after replacing ECM http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html
----------- Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------
2000 Jeep Cherokee Limited: KeyFob Remote Not Working? http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html
----------- Chevrolet Malibu: Key Stuck in ON position? http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html
----------- Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------
2012 Dodge Ram: Ignition Key will not release? http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html
--------------
These details will help.Thanks.

Nov 23, 2012 | 2006 Toyota Tacoma

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

Reprogramming remote and key


if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
Step Action
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.

Mar 26, 2009 | 2004 Isuzu Rodeo

3 Answers

Keyless entry for 05 Kia Sportage


i have a kia optima my keyless quit working to.I took it back to the dealer and the said it was common on a lot of kia models.They replaced the module for the keyless remote,that seams to have fixed it.

Mar 17, 2009 | 2004 Kia Optima

3 Answers

Keyless remote reprogramming


this has to be reprogrammed at a dealership because they are the only ones that have a computer to do it

Feb 21, 2009 | 1998 Cadillac DeVille

1 Answer

Keyless entry remote doesn't work with old or new batery. If sensor is bad where is sensor and how do you know if sensor is prolem with keyless remote.


I had the same problem. Went to dealer who said it probably needed to be reprogrammed (around $45-50). Paid for premium assistance with FixYA. Ginko gave me the procedure to reprogram my remotes. It was very easy and worked great. Now both of my remotes are working and it only cost me $9.99.

JOECOV

Jul 29, 2008 | 1999 Buick Century

Not finding what you are looking for?
2005 Cadillac Deville Logo

Related Topics:

453 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...