Question about 1995 Chrysler LeBaron

3 Answers

Working on a Chrysler LeBaron 3.0 Serpentine Belt after installed keeps coming off power steering pump1/4 inch

Posted by on

  • hutchingsm Oct 01, 2009

    The old belt was doing the same thing it wore the outside edge off of the serpentine belt about a 1/4" I put on the new correct belt everything in place and start engine and it immediately runs off the power steering pump again

  • Anonymous May 11, 2010

    You mean with engine running.? Was the old one okey before your involvement?

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 29 Answers

Check all pullys for play

Posted on Oct 01, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 312 Answers

You need to check to make sure it is in fact the correct belt. You also need to check the tensioner. If the tensioner is bad it's not going to put enough tension on the belt which means it will be loose and will keep popping off.

Posted on Oct 01, 2009

Testimonial: "I will check this out but I think that the tension pulley is fine but will check again "

Ad

If the belt is routed correctly the ONLY two causes are idler pulley alignment and sorry to say your crankshaft pulley moved outward ,not to get too technical, and caused the tracking issue. You may if you can see in there which pulley is out. But it takes very little to throw a belt. Also agree with other comment

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Re install a serpentine belt on a 94 chrysler lebaron 3.0L


There should be a diagram attached to the car near where the belt goes showing how the belt is to run through the pulleys.
Newer vehicles have a tension pulley which is a pulley on a spring loaded arm that keeps the belt tight.

First run the belt on all the other pulleys and then use a wrench to hold the tension pulley back while you slip the belt on.

Older cars do not have a tension pulley and you had to usually loosen something like the alternator a little bit to get it on.

Mar 12, 2010 | 1994 Chrysler LeBaron

2 Answers

Serpentine belt not staying on.


the only water deflection dodge gave these cars was directly under the pully system if it has this and is still throwing belts check the tensioner

Dec 14, 2009 | 1994 Chrysler LeBaron

2 Answers

Do you have a diagram on how to install a serpentine belt on a 1994 Chrysler LeBaron?


1994 CHRYSLER LEBARON - V6 3.0L 2972cc 181ci GAS FI N 3

Open the hood, the diagram for the serpentine belt is on the cowling.

From DAYCO Catalog
Belt Routing Diagram (Alt., P.S., Idler & Tens.)
9e1b1eb.jpg


From comments to other users and Lebaron Owners; for remove, starting at the alternator pulley and going clockwise around the pathof the belt, the belt drops down and forward and goes under the idlerpulley, continues forward and less steeply downward and goes around thecrankshaft pulley clockwise, rises rearward going over the top or thetensioner pulley counterclockwise, then drops down and around the powersteering pump clockwise and rises to go around the alternator pulleyclockise (which is where I started the description). To loosen thetension to remove the belt, or to give you slack to install the beltwithout having to force it over a pulley while under tension you rotatethe tensioner pulley arm around its pivot clockwise according to the'94 shop manual. It doesn't show by what means to effect this rotation,but in the earlier manual I have ('89) it shows there to be a 1/2"square hole in the tensioner arm into which you insert a breaker barwith a 1/2" square drive which gives you the temporary lever to rotatethe tensioner against its spring action. I assume there is a similar1/2" square hole on the '94 you are working with. Interestingly,between '89 and '94 the idler pulley was added, and the requiredrotation of the tension arm changed from counterclockwise to clockwiseto relieve the tension."

I think this will help you get the belt on. Good luck.

Oct 13, 2009 | 1994 Chrysler LeBaron

3 Answers

I need a serpentine belt diagram for a 1992 chrysler lebaron 3.0 liter v6


1992 CHRYSLER LEBARON - V6 3.0L 2972cc 181ci GAS FI N 3

Serpentine Belt Diagram Alt., P.S., Idler & Tens.

669b86a.jpg

More details you can find in DAYCO Catalog

I hope help you whit this (remember rated this help) Good weekend.

Oct 02, 2009 | 1989 Chrysler LeBaron

2 Answers

Where can i find a diagram to install serpentine


Most parts stores can print this out for you for free.

Sep 10, 2009 | 1991 Chrysler LeBaron

1 Answer

Serpentine belt slipped off due to anti-freeze.


Probably wet electrical components. Use an air hose to blow everything off , and let it dry good before you try it. Or, the mass air flow sensor could be dead.

May 04, 2009 | 1995 Chrysler LeBaron

1 Answer

Serpentine belt


when you buy brand name belts such as gates or good year belts the wrapper of the belt will come with a diagram to use it as a guide for installing the belt

Oct 31, 2008 | 1995 Chrysler LeBaron

1 Answer

How to put on Serpentine belt for 92 Chrysler Lebaron 3.o liter engine


Before replacing or installing the old belt you need to check all of the pulley's that the belt rides on for play. Pay special attention to the spring loaded tensioner pulley. They can sieze and cause the belt to come off.

I found this picture it is a bit large for the screen.

80003475.gif

Aug 29, 2008 | 1995 Chrysler LeBaron

4 Answers

Need a belt diagram


Good Day,

6fbb0fa.jpg

4a9a5c2.jpg
One is with A/C the other w/o.

Hope this helps

Jul 08, 2008 | 1995 Chrysler LeBaron

Not finding what you are looking for?
1995 Chrysler LeBaron Logo

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...