Question about 2000 Ford Windstar

1 Answer

How do you remove the front rotors on a 20000 ford windstar. I have the calipers off already

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 312 Answers

Check the lugs to see if there's a clip on one or more of them. If there is just pop them off and the rotor will pop off. If there are no clips chances are the rotor is oxidized and needs a helping hand with a rubber malet from behind.

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front brake rotor replacement 2008 ford fusion


loosen the lug nuts, Jack it up , take the tire off , remove the caliper an caliper mounting bracket , pull off rotor !

Oct 24, 2015 | 2008 Ford Fusion

1 Answer

Need instructions to remove the front rotor on F250 Four wheel drive truck - 2001 year


  1. Raise and support the vehicle; Remove the wheel and tire assembly;
  2. After removing the tire, remove the brake pads;
  3. Remove the disc brake caliper by removing the two disc brake caliper pin bolts. Lift the disc brake caliper from the disc brake caliper anchor plate (2B292). If necessary, remove the V-springs.
  4. Remove the pads. Remove the front disc brake caliper anchor plate stainless steel rail clips.
  5. Remove the rotor.
  6. Note: Perform this step for DRW vehicles. Remove the eight hub extender nuts, the hub plate and the rotor. Remove the eight hub plate nuts. Remove the hub plate. Remove the rotor.

Mar 02, 2011 | 2001 Ford F250 Super Duty Super Cab

1 Answer

How to change break rotor on 1999ford windstar


Remove brake caliper and then the three torx screws from factory rotor. (most replacement rotors omit the screw holes). Rotor will then pull off. If it is frozen in place, a couple of strikes to the rotor edges with a RUBBER mallett will usually break it loose.

Oct 02, 2010 | 1999 Ford Windstar

1 Answer

How to remove front brake rotors on Ford expedition 2003


Remove caliper and caliper bracket, some time the rotor will have two small metal clips remove them, also some times you have to used a hammer due to rust, rotor should slide off,

Aug 18, 2010 | 2003 Ford Expedition

1 Answer

How to change the brakes on a 1998 ford windstar?


Very easy! I owned several different year Windstars....very good van...

Changing the pads are very easy. Here is the instructions:

Removal & Installation
  1. Remove the brake master cylinder reservoir cap. Siphon and recycle approximately half the fluid from the reservoir.
  2. Raise and support the vehicle safely.
  3. Remove the wheels.
  4. Remove the disc brake caliper guide pins.
It is not necessary to disconnect the hydraulic lines.
  1. Lift the disc brake caliper from the anchor plate.
  2. Position the disc brake caliper out of the way by suspending with a wire.
  3. Remove the brake pads from the anchor plate.
To install:
  1. Inspect the rotor surfaces for scoring or buildup of lining material. Minor imperfections do not require machining. Hand sand the glaze from the rotor using 150 grit aluminum oxide sand paper.
  2. Use a C-clamp and wooden block to seat the disc brake caliper hydraulic piston in its bore, as illustrated. This must be done to provide clearance for the disc brake caliper to fit over the front rotor during installation.
  3. Remove all built-up rust from the inside of the brake caliper pad contact area.
  4. Install the brake pads, with the clip on insulators, into the front brake caliper anchor plate.
  5. Install the disc brake caliper onto the anchor plate.
  6. Install the disc brake caliper guide pins and tighten to 23-38 ft. lbs. (31-38 Nm).
Failure to tighten the lug nuts to the proper torque in a star pattern may result in damage to the brake rotor.
  1. Install the wheel and tighten lug nuts to 83-112 ft. lbs. (113-153 Nm).
  2. Lower the vehicle.
  3. Pump the brake pedal to seat the brake pads.

May 28, 2010 | 1998 Ford Windstar

1 Answer

After removing the caliper/pad assembly how do i remove the rotor/disc from the hub?


front wheel drive,,,remove caliper bracket two bolts holding it on ,,use at least a1/2in drive pull bar,,,these bolts are torqued very tight,be sure to tighten them with a lot of umhp,when u reinstall rotors,,,any way composite rorors should just come right off

Jul 08, 2009 | 2001 Ford Windstar

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

1 Answer

96 ford windstar


most likeley the front calipers are hanging up and heated up the rotors warping them. the cheapest way out is jack up each side of the van and spin each tire while someone slightly presses the brake to find out what wheel has a pulsation hesitation. then pull that brake caliper off and clean and re grease the gliders that alow it to slide back and forth and cut that 1 rotor. most likeley you will need to do this to both sides and replace the pads plus check the caliper pistons that they move freely. so to sum it up you might need a complete brake job.

Apr 30, 2009 | 1996 Ford Windstar

1 Answer

Need to change a rotor. what tools do I need I already have the calipher off. I now have to remove the caliper mount.


Just completed doing my rotor place a car jack stand or stack 2 blocks on each side of your A frame. Let jack down and place some blocks behind front of and rear of tires left on the ground. To remove your caliper mount look on reverse side of caliper mount for 2 large hex bolts. Lightly spray around them with some liquid wrench (try not to get spray everywhere). Remove bolts with a wrench and probably a hammer or a ratchet and a hammer. Tap lightly on wrench using short strokes. If this doesn't loosen the bolts use some heat (heated wrench technique) small propane kit to heat caliper mount not too hot just enough to heat it up to just above too hot to touch then reapply wrench tapping lightly. You need a C-Clamp to push the caliper in. After caliper is in remove c-clamp from caliper. If the caliper wont go in you have to replace it. Remove rotor cap with a flat head screw driver and hammer tapping around the edges lightly. Remove the pin out of the bolt behind the rotor cap. Remove nut then remove rotor. Some vehicles will not have a nut and pin system, just a shaft to hold the rotor in place. If the rotor is rusted on tap firmly on inside (back side) of rotor to break it loose from the rust . Spray rust with liquid wrench let sit for 2 minutes then wipe dry. Use a clean cloth or rag to handle new rotor. Slide new rotor on the shaft and replace nut the pin (if no nut and pin continue to next step. Place caliper over rotor and screw in hex bolts on back side of caliper using a wrench or ratchet tighten 1/2 turn of being tight. Re -attach caliper mount onto caliper. Tighten 1/4 turn past tight. Lift truck with jack replace tire and remove jack stands and or blocks from under A frame let truck down and remove blocks
wutxtye0rjd9d9ekmodqt1eoxkvn9hr9qjz1l3dabggyud7sdgr36czsrfxqenadhnijx9nfayi+sz1sug0aaaaasuvork5cyii=

Apr 22, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...