Question about 2005 Dodge Caravan

1 Answer

The lock on the sliding door won't lock with the remote control, how do i remove the moulding on the sliding door

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can pull the seal off the door and look at the rods and mechanisms

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2009 Equinox rear hatch has no manual latch and the remote will unlock all doors except the rear latch


If there is no exterior handle to open the hatch you are in a pickle. The rear hatch interior moulding assembly will have to be removed from inside the vehicle to access the lock assembly. This may crack/damage the moulding assembly as it is not designed to be removed this way. Once removed the door can usually be opened manually and then diagnosed for the problem. It may be a defective lock solenoid or latch assembly. I would have a pro look at it as they know how to disassemble these things with minamal to no damage.

Apr 06, 2015 | 2009 Chevrolet Equinox

1 Answer

2002 Expedition driver door won't lock/unlock with remote


This sounds like you may have a bad lock actuator, there is an actuator that controls the lock, it may need replacing, you will need to remove the door panel to gain access to it, then with a testlight you will test to make sure the actuator is getting power and a ground and if it tests good for power and ground then replace it and door lock will start working again, this part is about 30.00 dollars. here is a picture of it. good day3_10_2013_6_17_11_pm.jpg

Mar 10, 2013 | Cars & Trucks

1 Answer

2006 dodge caravan sxt passenger door sliding door won't unlock or open at all, manually or by remote


U will have to take the inside door cover off and manualy open it. And replace the electric door locking switch. Very common problem. Get the new lock and latch assembly from dealer,

Jun 13, 2012 | 2006 Dodge Caravan

1 Answer

Need to put passenger miror on. i need help to show me how to take the door panel off.


Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal
  1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
  1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
  1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.


    Trim Panel


    ar0885a.gif


    Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole
  1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
  1. Remove two screws located at bottom of front door trim panel.
  1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
  1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
  1. Pull front door trim panel from the top to release hooks from front door .
  1. Remove front door trim panel.
Installation
  1. Replace any bent or damaged fasteners.
  1. Follow removal procedure in reverse order.
Body Side
Removal
  1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
  1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
  1. Remove forward and rearward mating sections from under window trim.
Installation
  1. Replace all christmas tree fasteners.
  1. Follow removal procedure in reverse order.
  1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.


    r11176a.gif

Back
Removal
  1. Disconnect rear window defroster wires.
  1. Remove the liftgate window garnish moulding as described.
  1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
  1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
  1. Remove liftgate trim.
Installation
  1. Follow removal procedure in reverse order.


    Liftgate


    r10441a.gif

2010&c18=modelyear&c35=wsm%2ctrim%20panel%2c%20door%2csww%2c01-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1998 Ford Windstar

1 Answer

2000 cadillac deville remove door panel


2000-2001 Deville Door Panel Removal:

1. Position window fully downward and ensure manual lock knob is in unlock position.
2. Disconnect locking clip at front of manual lock knob, by insertingsuitable flat bladed tool into top service notch.
3. Remove manual lock knob.
4. Remove inside handle bezel by holding inside handle to open position, inserting sutiable flat-bladed tool at front lower corner and prying outward.
5. Remove bezel.
6. Remove inside door handle mounting screw.
7. Disconnect eight retainers around outside edges of door trim panel using clip zip tool No. J-36796, or equivalent.
8. Slide door trim panel upwards to release alignment datums, eight retainers, armrest steel retainer clips and inner belt mouldings (see fig #7 amd #8).
9. Disconnect electrical connector(s).
10. Reverse procedure to install.

23785ad.jpg

Hope this help (remember rated this).

Mar 28, 2010 | 2000 Cadillac DeVille

2 Answers

2000 ford windstar power door locks do not work and have checked every fuse


The actuactors for your locks have a little motor in them. In this motor there is a resistor that will give out over time. Usually the locks gradually stop working over time. You can remove the actuator and take it apart and fix by removing the resistor in the motor and putting a peice of copper in its place. Takes about 30 minutes per door if you know what you are doing. Do a google search for ford windstar door lock fix and you will find several blogs with detailed descriptions of the repair.

Jul 02, 2009 | 2001 Ford Windstar

1 Answer

Rear door on driver side won't open,have taken the panel off the inside of car,seems like the lock won,t travelas far as it does on the other door.is there any way to open this door,thanks[1997 lincoln...


Rear
Removal
  1. Using a small screwdriver, remove the screw cover from the armrest of rear door trim panel (27406).
  1. Remove the two retaining screws.
  1. Using Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry rear door trim panel from door inner panel.
  1. Disconnect electrical connectors.
Installation
  1. Position rear door trim panel on door inner panel, aligning two locators on rear door trim panel. Reverse Removal procedure.
------------------------------------------------------------------------------------ Rear
Removal
  1. Remove door trim panel and watershield. Refer to Section 01-05 .
  1. Check all connections of remote control links and cables. Service as necessary.
  1. Remove remote control assembly.
  1. Remove door latch remote control assembly from latch assembly.
  1. Drill out rivet at bellcrank and link (264B14).
  1. Remove three screws attaching latch assembly to door.
  1. Drill out rivet that attaches actuator motor to door.
  1. Remove latch assembly with actuator motor and door latch control rod lever link assembly.
Installation
  1. Install new bushings and clip onto latch assembly.
  1. Install latch with links and power lock actuator into door cavity.
  1. Position latch assembly to door, aligning screw holes in latch and door. Install three screws. Tighten to 10-13 Nm (89-115 lb-in).
  1. Attach door latch actuator motor to door with a new rivet.
  1. Install bellcrank and link to door using a new rivet.
  1. Install inside door handle and remote control assembly to door.
  1. Open and close door to check latch assembly operation.
  1. Install watershield and door trim panel. Refer to Section 01-05 .
ee8a11f.gif
Item Part Number Description 1 221A00 Door Handle to Door Latch Actuating Cable 2 26446 Rear Door Control Rod Retainer 3 377901 Plug Button 4 26412 Rear Door Latch 5 W623451-S2 Push Nut 6 224A32 Counter Balance 7 22450 Door Outside Handle Tension Spring 8 W701210-S309 Screw 9 224A20 Outside Door Handle Anti Rattle Pivot (2 Req'd) 10 22404 Door Handle 11 224A24 Front Door Outside Handle Spacer (2 Req'd) 12 264A64 Rear Door Actuating Rod 13 22408 Outside Door Handle Anti-Rattle Bumper 14 22428 Outside Door Handle Large Pad 15 N621906-S2 Nut (2 Req'd) 16 N807329 Screw (3 Req'd) 17 26595 Rear Door Electric Latch Actuator (RH) 18 W701566-S47 Rivet 19 431C04-A Rear Door Latch Striker Assembly 20 — Door Lock Striker Plate (Part of Door Shell Assy) 21 W525172-S Rivet (2 Req'd) 22 264B14 Bellcrank and Link (RH) 23 264A50 Bushing 24 N802034-SG Rivet 25 26420 Rear Door Latch Control Rod Link 26 W525172-S Rivet (2 Req'd) 27 21818 RR Door Latch (Inside) 28 A26460 RR Door Latch Push Button Rod 29 21982 Door Latch Rear Striker Assembly 30 N808377-S101 Screw (2 Req'd) 31 250A04 Rear Door Catch 32 N801010-S100 Truss Head Bolt (2 Req'd) 33 N804234-S2 Screw 34 266A74 Rear Door Latch Actuator Retainer 35 24630 Rear Door 36 26552 Rear Door Latch Control Escutcheon A — Tighten to 21-29 Nm (16-21 Lb-Ft) B — Tighten to 10-13 Nm (89-115 Lb-In) C — Tighten to 7-8 Nm (62-70 Lb-In) D — Tighten to 26-34 Nm (20-25 Lb-Ft) E — Tighten to 3-4 Nm (27-35 Lb-In)

Mar 24, 2009 | 1997 Lincoln Continental

1 Answer

Front door panels


yes you need to remove the door panel and here is the instructions via TIS (Toyota info system)

DISASSEMBLY
1. REMOVE THESE PARTS:
HINT:
Tape a screwdriver tip before use.
(a) Door inside handle bezel
(b) Armrest
(c) Armrest panel base upper
(d) Courtesy light
(e) Lower frame bracket garnish
2. REMOVE DOOR TRIM
(a) Remove the 3 screws from the door trim.
(b) Using a screwdriver, remove the clip and remove the trim
by pulling all of the trim up.
HINT:
Tape the screwdriver tip before use.
(c) Remove the 11 screws and armrest base from the door
trim.
(d) Remove the inner weatherstrip from the door trim.
(e) Remove the 8 screws and door pocket from the door trim.
3. REMOVE THESE PARTS:
(a) Door belt moulding
HINT:
Pry out the clip from the edge of the panel, and remove the
moulding .
(b) Door weatherstrip
NOTICE:
Do not pull strongly on the weatherstrip as it may tear.
(c) Door inside handle
(d) Door lock control relay
(e) Service hole cover
BO2455
Cotton
Tape
Panel
Cover
BO−10
BODY − FRONT DOOR
NOTICE:
Do not block the trim clip sealing with the tape.
(f) Outside rear view mirror
(g) Door glass run
(h) Rear lower frame
HINT:
Adjust the equalizer arm up to down and tighten if where dimensions
A and B, as shown are equal.
(i) Door glass
(j) Window regulator
Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
HINT:
Apply MP grease to the sliding surface and gears of the window
regulator.
NOTICE:
Do not apply grease to the spring.
(k) Locking and opening control link
(l) Door lock
HINT:
Apply adhesive to the 3 screws.
Part No.08833−00070, THREE BOND 1324 or equivalent
Torque:5.0 N·m (50 kgf·cm, 43 in.·lbf)
BODY − FRONT DOOR
BO−11
HINT:
At the time of reassembly, apply MP grease to the sliding surface
of the door lock.
(m) Door outside handle
(n) Door lock cylinder
(o) Door speak

Mar 08, 2009 | 1997 Toyota Land Cruiser

1 Answer

Broken door handle - 2001 Nissan Quest SE


first you van order parts at discount from tascafordparts.com.
quest & mecrury villager are the same vehicle made at the same assembly plant. good luck to all. If you were in detroit area, I wold help you.

Trim Panel —Sliding Door Removal
  1. Remove the sliding door trim panel finish panel.
532ac84.gif 2. Remove the sliding door trim panel 2965fbe.gif Latch Remote Control —Sliding Door Removal
  1. Remove the rear sliding door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. If equipped, disconnect the sliding door power door lock actuator electrical connector.
f373e91.gif
  1. NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.
  2. Disconnect the sliding door rear latch cable.
  3. Remove the bolt.
  4. Remove the sliding door rear latch cable adjusting bracket from the latch remote control.
  5. Disconnect the sliding door rear latch cable from the latch remote control.
b8f2f32.gif
  1. Remove the 4 sliding door front latch bolts.
NOTE: If necessary, transfer parts to the new sliding door latch remote control.
Remove the sliding door latch remote control.
  1. Remove the bolts.
  1. Remove the sliding door latch remote control.
cb5ee71.gif
Handle —Exterior, Sliding Door Removal
  1. Remove the sliding door latch remote control. For additional information, refer to Latch Remote Control—Sliding Door .
  1. Remove the sliding door exterior handle.
    1. Remove the nuts.
    1. Remove the sliding door exterior handle.
0c820f3.gif

Mar 08, 2009 | 2001 Nissan Quest

2 Answers

Broken exterior door handle,passenger sider ,sliding


Got this idea from mpvclub.com: Get some stainless or aluminum sheet metal screws, drill pilot hole into the handle and into the receiving part behind, then screw in the screw. Do on both sides of handle (get appropriate length screw.) When done, get some putty or hardener to fill in the screw slot, let dry, then sand smooth, then paint with body color. Result is great and inexpensive.

Jan 26, 2009 | 2004 Mazda MPV

Not finding what you are looking for?
2005 Dodge Caravan Logo

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...