Question about 2004 Toyota Sienna

Open Question

Replace 2004 Seinna front wheel bearing - 2004 Toyota Sienna

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

  • 373 Answers

SOURCE: wheel bearing

HI, For replace the front wheel bearing. on a toyota corolla 03
You need a hydrualic bench.
Because they goin pressed.
I recomend go to a repair shop, is not easy.
It's take about 2 hour to do. with the right tools.

Posted on Jul 04, 2008

  • 321 Answers

SOURCE: front wheel bearing 2004 escape 4x4

It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Posted on Jul 11, 2008

SOURCE: 2000 toyota echo, wheel bearings

I found this site to be very helpful with this job: http://www.toyotanation.com/forum/showthread.php?s=714b28cb1c3f77f992209de0bdbfbd13&p=2481776#post2481776

Posted on Sep 23, 2008

  • 104 Answers

SOURCE: Moisture in headlight assembly, 2004 toyota seinna

Once the factory seal is leaking moisture, it can be hard to dry and reseal. You can try a hir dryer, and then look for a seam to lay silicone on, but the recommended fix is to replace the whole headlight assembly. The lens is not removable like on older lamps. The pieces are molded, and then epoxied together. Hard to split apart and get back together without damaging. Try a salvage yard.

Posted on Mar 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2wd.how to replace front wheel bearing assembly


There are a number of videos...
For RWD front hubs. (F250 will just have larger bolts.)

How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150
For 4x4 front hubs.

Ford Super Duty hub bearing replacement Driver side

May 06, 2016 | 2005 Ford F 250 Super Duty

2 Answers

Is it possible to replace a front wheel bearing at home on a 2004 Chevy Trailblazer?


You would be better off replacing the entire hub assembly. Yes, bearings need to be pressed into place and this requires a hydraulic press.

Dec 19, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

Bearing on front wheel


What about it? Most people question if you can just replace the bearing, or do you need to replace the whole hub assembly. Unfortunately, need to replace the whole wheel bearing hub assembly.

Dec 16, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

How to replace front wheel bearing on an awd 2004 pontiac vibe?


Hi, the front does not have a "wheel hub assembly". It is an individual sealed roller bearing that has to be pressed on and off the front spindle. It is a Toyota thing!
Take care

Aug 04, 2010 | 2004 Pontiac Vibe

1 Answer

Repair front wheel bearing assembly


no special tools in particular just the usual or necessary tools required.. 1stly u remove the Tyre and the caliper then u'll see something like a long rod dats the bearing

Aug 02, 2010 | 2004 Mercury Mountaineer

1 Answer

I am getting a pulsing feeling from the front wheels when braking on my 2004 Chrysler Sebring. It feels like one or more of the rotors are warped. How do I replace the front rotors with new ones. Thanks.


If they are not worn beyond tollerance they can be machined on the vehicle.
Also make sure its not tyres or wheel bearings.

remove wheel
remove brake caliper( leave the hose connected)
remove centre cap
remove split pin and lock
unscrew bearing hub nut
rotor should come off
fit new bearing races in new rotor
grease new bearings
fit inside bearing and seal
refit rotor, outer bearing,washer,nut,lock, splitpin and centre cap
(tighten nut until no play in bearing plus 1\8 of a turn)
refit caliper and wheel
bleed and test brakes before driving

Apr 28, 2010 | 2004 Chrysler Sebring

1 Answer

How do you replace the front wheel bearings on a 2004 Ford Escape


you must take both wheels off remove lower control arm, remove hub via wheel nut and the bearings must be pressed in at a shop or machine shop

Apr 20, 2009 | 2004 Ford Escape

2 Answers

My 04 ford explorer is making a loud humming noise when driving. The noise is coming from front and gets louder the faster you drive.


Try to rotate the tires to rule that out.If not then it sounds like the wheel bearing is going out, on some cars you can replace the bearings on others youi have to replace the hub assembly

Mar 25, 2009 | 2004 Ford Explorer

1 Answer

Chey aveo front hub bearing what is this?


yes front wheen drives have hub bearings. Most of them need the hubs to be pressed apart to replace them. the hub bearing supports the end of the CV drive shaft closest to the wheel. hope that helps.

Mar 17, 2009 | 2004 Chevrolet Aveo

Not finding what you are looking for?
2004 Toyota Sienna Logo

Related Topics:

770 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...