Question about 1993 Jeep Grand Cherokee

1 Answer

BEST PLACE TO FIND THE PLUG TO THE NEUTRAL SAFETY SWITCH?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Passenger side, near dipstick unless its a chrysler trans. then it will be on the trans itself, lr corner just above pan.

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a neutral safety switch in a 1990 f250. Can see it by the firewall but can't reach it


THE NEUTRAL SAFETY SWITCH IS ON THE TRANSMISSION,
REMOVE SHIFTER CABLE, REMOVE THE NUT THAT HOLDS THE LEVER IN PLACE, REMOVE THE ELECTRICAL PLUG REMOVE THE HOLDING BOLTS AND FINALLY REMOVE THE SAFETY SWITCH, INSTALL NEW ONE IN REVERSE PROSIGER.

Jul 23, 2014 | Cars & Trucks

1 Answer

2003dodge caravan neutral safty switch


Test/Service/Replace Neutral Safety Switch
Most neutral safety switches are combinations of a neutral safety switch and a backup lamp switch. Others have separate units for these two distinct functions. When the reverse light switch is not part of the neutral safety switch, it seldom needs adjustment, as it is directly activated by the transmission or the gear selector linkage.
f_ttat_t3.20.jpg Typical location of a neutral safety switch on a transaxle. Reprinted with permission of Ford Motor Company. A neutral safety switch allows current to pass from the starter switch to the starter when the lever is placed in the P or N position. Some neutral safety switches are nonadjustable. If these prevent starting in the P or N position and the gear selector linkage is correctly adjusted, they should be replaced.
To adjust a typical neutral safety switch:
  • Place the shift lever in neutral.
  • Loosen the attaching bolts for the switch.
  • Using the angling pin, move the switch until the pin falls into the hole in its rotor.
  • Tighten the attaching bolts.
  • Recheck the switch for continuity. If no voltage is present, replace the switch.
  • The switch sometimes controls the operation of the back-up lights also. With the engine off and the key on, put the selector in reverse position. Check the back-up lights to see that they are on. Then, check in the drive position to see that they are out.

Aug 15, 2012 | Cars & Trucks

1 Answer

Where is neutral switch on a 92 dodge caravan


Safety Switch Most neutral safety switches are combinations of a neutral safety switch and a backup lamp switch. Others have separate units for these two distinct functions. When the reverse light switch is not part of the neutral safety switch, it seldom needs adjustment, as it is directly activated by the transmission or the gear selector linkage.
f_ttat_t3.20.jpg Typical location of a neutral safety switch on a transaxle. Reprinted with permission of Ford Motor Company. A neutral safety switch allows current to pass from the starter switch to the starter when the lever is placed in the P or N position. Some neutral safety switches are nonadjustable. If these prevent starting in the P or N position and the gear selector linkage is correctly adjusted, they should be replaced.
To adjust a typical neutral safety switch:
  • Place the shift lever in neutral.
  • Loosen the attaching bolts for the switch.
  • Using the angling pin, move the switch until the pin falls into the hole in its rotor.
  • Tighten the attaching bolts.
  • Recheck the switch for continuity. If no voltage is present, replace the switch.
  • The switch sometimes controls the operation of the back-up lights also. With the engine off and the key on, put the selector in reverse position. Check the back-up lights to see that they are on. Then, check in the drive position to see that they are out.

May 10, 2012 | 1992 Dodge Caravan

1 Answer

Need location of neutral safty switch on my 1990 cadilac broughm 350 engin e


The neutral safety switch is located on the top and toward the base of the steering column almost to the floorboard.

To remove or install the neutral safety switch be sure to place the shifter in the neutral position, then dis-connect the wire connector at the neutral safety switch, then remove the securing screws and then remove the neutral safety switch.

Install the new neutral safety switch and do not over-tighten the securing screws, then remove the alignment pin and re-connect the wire connector to the neutral safety switch. (be sure not to remove the alignment pin until the neutral safety switch has been installed)

Check to be certain that the vehicle only starts in "Park" or "Neutral". Here is an image to help assist you, and let me know if you require any further assistance.


f494426.jpg

Sep 12, 2010 | Cadillac Brougham Cars & Trucks

2 Answers

Bronco wont start 88 ford bronco just replaced tranny and now won't start. i've hooked everything back up but one of the wires to the transfer case bc i broke the plug in. any ideas why it wont start...


The neutral safety switch is located on the side of the transmission and it is usually attached behind the shifter linkage and it is secured with two small bolts that can be loosened up to allow for adjustment of the neutral safety switch.

To adjust the neutral safety switch place the transmission into neutral, (block the tires) there is a notch or and indent marker on the housing of the neutral safety switch that should be lined up with a line on the face of the collar that is around the shifter detent shaft, and if they are not in alignment then loosen the two bolts that secure the neutral safety switch and then turn the neutral safety switch until they are aligned and then tighten the securing bolts to the neutral safety switch, and then test the starter. If the starter fails to engage then either the neutral safety switch is faulty, the neutral safety switch has been by-passed all this time and the by-pass (I will usually find things like a paper clip shoved into the vehicles wire connector with electrical tape around it) has fallen out of the wire connector from the vehicle wiring harness, or the battery just went dead. if you have the neutral safety switch from the old transmission still available try using it to test the neutral safety circuit. I have provided you with an image to help assist you adjust the neutral safety switch.


0b4222e.jpg

Jun 20, 2010 | 1988 Ford Bronco

2 Answers

How to replace neutral saftey switch on a 1980 cadillac deville?


Use like reference guide for GM Cadillac 1967-1989 Repair Guide Neutral Safety Switch - REMOVAL & INSTALLATION

All Except 1985-89 Eldorado and Seville
See Figure 1
The neutral safety switch prevents the engine from being started in any transmission position except Neutral or Park. The switch is located on the upper side of the steering column under the instrument panel on column shift cars, and inside the shift console on floor shift models.
  1. Remove the console for access on floor shift models.
  2. Disconnect the electrical connectors.
  3. Remove the neutral switch.

To install:
  1. Place 1967-70 column shift lever models in Drive, and 1971 and later models in neutral. Locate the lever tang against the transmission selector plate on column shift models.
  2. Align the slot in the contact support with the hole in the switch. Insert a 3 / 32 in. (2.38mm) diameter pin in place. The switch is now aligned in Drive position.

1973 and later neutral safety switches have a shear-pin installed to aid in proper switch alignment so that insertion of a pin is unnecessary. Moving the shift lever from Neutral shears the pin.
  1. Place the contact support drive slot over the drive tang. Install the switch mounting screws.
  2. Remove the aligning pin. Connect the electrical wiring, and replace the console.
  3. Set the parking brake and hold your foot on the service brake pedal. Check to see that the engine will start only in Park or Neutral.
7b3f2a9.jpg

Fig. 1: Installation of a common neutral safety switch



ADJUSTMENT
See Figure 2
1974 and later cars do not have a neutral safety switch. Instead, these cars have an interlock between the lock and the transmission selector, which is non-adjustable.
  1. Place the shift lever in Neutral.
  2. Move the switch until you can insert a gauge pin, 3 / 32 in. (2.38mm) diameter, into the hole in the switch and through to the alignment hole.
  3. Loosen the switch securing screws. Remove the console first, if necessary.
  4. Tighten the screws and remove the pin.
  5. Step on the brake pedal and check to see that the engine will only start in Neutral or Park.
05843d3.jpg


Fig. 2: Adjustment of a common neutral safety switch


1985-89 Eldorado and Seville
See Figure 3

All neutral safety/back-up light switches come with a small plastic alignment pin installed. Leave this pin in place.
  1. Place the shifter assembly in the Neutral position.
  2. Remove the shifter lever-to-switch nut and the lever.
  3. Disconnect the electrical connector from the neutral safety/back-up light switch.
  4. Remove the neutral safety/back-up light switch-to-transaxle bolts and the switch from the vehicle.

To install:
  1. Position the shifter shaft in the Neutral position.

If using an old switch or the plastic pin (new switch) is broken, install a3/32in. (2.38mm) diameter pin gauge (drill bit) into the neutral safety/back-up light switch; the switch is then locked into its Neutral position.
  1. Align the flats of the shifter shaft and the neutral safety/back-up light, then, align the switch-to-tang on the transaxle. Torque the switch-to-transaxle bolts to 22 ft. lbs. (30 Nm). Remove the pin gauge.
  2. To complete installation, reverse the removal procedures. Make sure that the engine starts only in the Park and Neutral positions.
c796664.jpg

Fig. 3: Neutral start and back-up lamp switch - 1985-89 Eldorado and Seville

Hope help with this (remember rated and comment this). Good luck.

Mar 21, 2010 | 1980 Cadillac Deville

1 Answer

Neutral safety switch


The neutral safety/back-up light switch is located at the transmission. I am attaching a photo for reference. Hope this helps and best wishes.

08face1.jpg

Aug 03, 2009 | 1992 Ford Bronco

2 Answers

Firebird Won't start


Very possible its the neutral safety switch. Try putting the car in neutral and turning the key. If it starts then I'd investigate the linkage and/or neutral safety switch. Best of luck.
Greg

May 29, 2009 | 1999 Pontiac Firebird

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...